Ford F-150 - 1997-2003 :: Loud Popping Noise Almost A Clunk When Making A Slow Sharp Turn
Lariat stepside, 5.4L with 150k miles. Loud popping noise, almost a clunk, when making a slow sharp turn. Put it on jackstands and did the normal tire grab and shake and found no issues there. Tie rods, ball joints and sway bar links all seem tight. Looked for signs of unusual rubber to metal and metal to metal wear and found nothing. The only thing I did see was the rubber boots on the upper control arm ball joints were split. What I have checked or if I am missing something?
View 9 RepliesSanta Fe (DM - 2013+) :: Squealing Noise On Sharp Left Turn
I have a 2013 Santa Fe with a 2.0T. A couple of days ago, I heard a squealing noise when I make a sharp turn to the left, like maybe a power steering belt would do. This has continued and I have also noticed that the AC fan almost completely dies at the same time. Car has 6,000 miles.
View 3 RepliesSanta Fe (DM - 2013+) :: Grinding Noise Coming From Rear Of Vehicle On Sharp Turns Under Moderate Acceleration
I own a Canadian 2013 Santa Fe sport AWD 2.0l turbo. Back in June/ July 2015 I noticed a poping / grinding noise coming from the rear of the vehicle when ever I made sharp turns under moderate acceleration. I brought my car into the dealer as it was still under warranty. They diagnosed the problem to be my viscous coupler apparently it was defective.
The part was ordered and replaced about 3 weeks later. After the warranty work was completed in still noticed a noise coming from the back end. I took my car back to the dealer. They found that the rear tires were "cupped" they recommended to get a 4 wheel alignment to solve the cupping issue.
In my past experiences tire cupping is usually caused by a worn out suspension component such as bad shocks. So to avoid conflict of interest I took my car to Canadian Tire to get the alignment checked and adjusted.
Sure enough the front wheels only were slightly out of alignment and a minor adjustment was made. No adjustments made to the rear. The technician advised me that due to the minor adjustment, the alignment would not cause my rear wheels to cup. The complete suspension was checked and no problems were found.
So...would a bad viscous coupler cause wheel cupping???
My Santa Fe had 48000kms at the time of the original noise was detected.
I do not tow a trailer or haul overloaded loads.
The majority of kilometres made Is done on highway.
The rear tires have now been rotated to the front.
Camry :: Popping Noise Coming From The Roof When Turn Into Driveway?
2007 camry se makes a popping noise when i turn into my driveway, or any driveway for that matter. Its annoying, and im puzzled as to what it can be. My worst fear is that this car was in a bad wreck.
View 8 RepliesLexus GS 2013+ :: Popping Noise When Turn Left Or Right While Backing Out Of Garage Or Parking Spot
Ok had my driver side front cv axle replaced. But not when only backing up and turning I hear and feel a popping sound. Happens when I turn left or right while backing out of garage or parking spot.
View 1 RepliesVolvo - S60 :: 2002 - Metallic Popping Noise Coming From Right Front Side Every Time Making A Turn
I have owned a 2002 Volvo S60 2.4L for the past two years, and she has served me well. However, I have been having issues lately. She has hit 179,400-ish miles and with age things have started to fail. I want to know how much it will cost to fix these things and if I can do it myself.
There is a metallic popping noise coming from the right front side of the vehicle every time I make a turn (I haven't particularly noticed if it's a left- or right-hand turn when it happens.) I have been advised by my father that it's probably a CV (constant velocity) joint. Is that what's causing the noise?
My right front headlight has gone out, and I've replaced the bulb as well as the fuse, but it's still out. Could it be faulty wiring? The left front blinker has stopped blinking, I hope that's as simple as changing out the bulb.
The shift is automatic, but in the mornings (I've noticed it's mostly when it's cold outside) I attempt to move the shifter out of park and it won't budge for several minutes. Sometimes I have to turn the engine off, and then turn it back on for the shifter to move.
One last question- how often should I change and/or flush my transmission fluid and the filter, and can I do that myself or should I take it to the dealership? (Which I am reluctant to do.)
Ford Super Duty (1999-2016) :: Rear End Groaning When Turn Sharp Corner
I have a 2013 F350 DRW, 3.73 gears LS. 25K on the thing.
Today I notice that when I turn a corner I get a groan. At first I thought that maybe the springs are doing it. I sprayed them down really good with fluid film. No change.
So I had my daughter drive the truck with me standing on the rear bumper. It is definitely in the rear end. It is quiet when in a straight line.
Golf IV R32 :: Odd Pop Or Click Noise When Make A Sharp Turn
Sometime when I make a sharp turn (such as turning out of a parking lot) I hear a "pop or click" noise coming from the front end. I cant tell whether this is normal or not and I wanted to know if this was a sign of anything serious. The car only has 70k miles and is in pretty good shape. Still stock suspension.
View 8 RepliesToyota - Avalon :: Loud Cracking And Popping Noise Coming From Radio When On Or Off
I have a 2007 Toyota Avalon Limited. For the last three years or so I get a very loud cracking noise from the Radio, I can even turn it off and it continues or gets louder. I took it to the dealer, they think it is some of the speakers. Since are 12 speakers, not sure I want to start replacing them. I thought it might be the amplifier, took to an electronics guys. He took a lot of the car around the radio apart, we could never find the amplifier. I think the amplifier is in the trunk with the GPS Disk Player. If you were going to replace something, would be the radio, amplifier, or? The only way to stop it is to remove the fuse which causes the radio and GPS screen to not work.
View 3 RepliesCamry :: 2009 LE Grinding Noise On Sharp Left Turn?
I have 35k on my 2009 camry, (past warranty). All of a sudden in the last few days when I make a sharp left turn (like into a parking spot) I hear a grinding noise from my car. Not really a full on grinding, but like a quiet fart can muffler noise. No issues with alignment, driving straight, or sharp right turns.
View 5 RepliesPassat (B5) :: Clicking Noise When Make A Sharp Turn - Bad CV Axle?
The other day i noticed that when i make a sharp turn left or right i hear a clicking noise. If the clutch is engaged it clicks and if its not then it does not click. It is also louder when i turn right... I am thinking CV axle!
View 4 RepliesCamry :: 2003 LE - Rubbing Noise When Making Sharp Right Turn At Low Speed
At 120k miles, my 2003 Camry LE 2.4L started to make some noise when making sharp right turn at low speed (below 5mph) going forward. It sounds like the tire rubbing the fender or somewhere, not metallic, and it's periodic, at 2-3Hz or so. It comes from somewhere on the driver side but I'm not sure. The car doesn't make noise when turning at stop or backing up or going straight, and the noise seems to disappear if turning at higher speed (maybe the turn is not sharp enough).
First I suspect the tire is rubbing the fender. But after inspection, no rubbing marks can be found, and there seems no rubbing when the car is parked and the wheel turn all the way to the right. Then I suspect a bad CV axle. But the boots seem in good shape with no leaking grease, and there's no noise when backing up.
Gmc - Yukon :: 2007 4WD - Grinding Noise In The Front When Make A Sharp Turn
I'm having 4WD problems with my Yukon, but the dealer keeps telling me there's nothing wrong with it (this has been going on for 2 winters now), which is either code for, "let's wait until it's extended warranty expires, so we don't have to pay for it," or "the computer says nothing is wrong, so that's all we're going to look at." When it's in 4WD, anytime I make a sharp turn or even turn a corner there's a grinding noise in the front, if I try to back up, it will only go as far as one revolution of the tires then stop (I have to take it out of 4WD to backup), eventually the "Service 4WD" light comes on, but apparently nothing gets recorded on the computer. It has 32,000 miles on it.
View 6 RepliesAzera TG (2006-11) :: Transmission Noise On Sharp Turn On Cold Days
On cold mornings if I do a sharp right turn (Left turns just naturally are not sharp, so I don't know if it's both ways). I get a rumbling noise in the transaxle. It sounds like a rumble, if it's limit slip noise it's pretty bad. It does not seem to be a problem in the summer. Dealer found nothing but if they don't do it while it's cold they won't hear it.
View 2 RepliesJeep - Wrangler :: Bumping Noise On Sharp Turn Slow Speed
2004 Jeep Wrangler Sport 5-speed Bought used 2yrs ago. 76,000 miles Only seems to happen after driving for more than an hour. When I either back into my driveway or turn sharp into a parking sport, mostly to right, I get a bumping sound, like something rubbing. My mechanic has replaced the sway bar links, front rotors, axle yoke, had a front differential leak so seal was replaced, and am still getting the sound. Tires Bf Goodrich All Terrain Do not do off road.
View 4 RepliesGolf IV / Jetta IV :: Spring-clicking Like Noise When Make A Sharp Right Turn At Low Speed
So the Jetta developed a new noise lately that sounds just like what can be head on this video.
The spring-clicking kinda noise only happens when i make a sharp right turn at low speed and seems to be coming from the driver's side. So i though bad outer cv joint.
Well, I put on a brand new OEM unit last night and noise is still there.
Ford - Explorer :: 1999 XLT - Clunking Noise From Front End On Making A Sharp Turn
For the last few weeks, when I make a turn (particularly a sharp turn in either direction) I get a "clunking" noise that sounds like it is coming from the front end somewhere. I can also feel it - almost like a gear slipping and engaging again. I am not in 4WD mode when this is happening. It NEVER happens unless I am turning a corner. If I drive straight, it's fine. 1999 Explorer XLT (4 door, 4wd model)....
View 2 RepliesCivic - Honda :: Noise From Front Passenger Side Wheel On Sharp Right Turn Going Downhill
I have a 2005 Honda Civic that was making noise on the front passenger side wheel and what sounded like the front driver side strut clanging (bottoming out) when I hit a bump, sharp right turn heading down hill, or hit a pot hole (small or large). I brought it in to a mechanic to diagnose the issue. They told me I had a bad wheel bearing and also needed new struts. They quoted me a price on parts and labor that I thought was too high, so I checked a few other mechanics to make sure that I needed the work and try to get a better quote. All said the same work needed to be done, so I eventually had them repaired.
My car seems to ride better and I don't hear the noise from the front passenger side wheel anymore or the noise from the front driver side strut, however, there is now a clunking like sound coming from the front suspension (left and right sides). It sounds kind of like something might be loose. I can hear it over slight bumps, and when turning whether I'm going slow or even coming out of a parked spot.
Is there something else that may need repair after having all this other work done? Have I caused a "needed repair chain reaction" or something?
Santa Fe (DM - 2013+) :: Rubbing And Popping Noise From The Rear Of Vehicle
I have had my Santa Fe since middle of January and have some issues with rubbing noises and popping noises from the rear of the vehicle since then. The rubbing noise has been resolved, but the popping noise appears to be more of a challenge. I have had the vehicle looked at 4 times.
The way the mechanic at the dealership explained it to me is that between the outer body panel and the inner trim panel there is a piece of sheet metal that is flexing and popping. This is most noticeable at low rates of speed and more when turning left or right.
The past two times the dealer has reposition the pieces and the noise has went way for a few days, but always returns. So today I asked if maybe there was a wield missing or what we do if the problem continues after the latest fix.
One suggestion was to fill the gap between the sheet metal and the body panel. They mentioned foam or cardboard.