Golf IV R32 :: Cable Shifter Adjustment Gone Wrong?
Ok so I was putting a drill bit into the home slot under the shifter boot. I didn't realize it was so deep and the piece dropped all the way down the hole. Is this bad? If so, what can I do to get in there and get it?
View 5 RepliesCamry :: 1992 - Changing Rear Brake / Adjustment?
Changing brakes on the 92 camryHow do i adjust them ??They have the auto adjuster but can i get them close before i put the hub back on or is it go in reverse and keep hitting the brakes.I used to know but i forget
View 19 Replies7 Series :: Bmw 735il 1988 - Ticking In Valve After Adjustment
Bmw 735il 1988 : Car has been sitting for 4-years I have done all the maintenance including the Valve adjustment .012 cold. I hear a louder then normal ticking in the valve train seems like its coming from the intake side towards the rear. I double checked all the gaps several times and they are correct. Could this be a carbon build up, plugs were black due to a bad coolant sensor everything tune up related has been replaced. Before the adjustment I started the car for a few minutes and did not hear the ticking, does it need to go for a long drive or am I missing something? Is there a way to narrow with valve is causing this, could it be the oil tube blocked on the rear section? Can I remove the valve cover and observe with out taking an oil bath?
View 3 RepliesToyota - Pickup :: 1986 - Valve Adjustment Cold Or Hot?
When adjusting valves on a 1986 22RE Toyota engine, the manual says to adjust intake to .008 and exhaust to .011 when the engine is "hot". I was doing some research and it seems to be a somewhat common practice to adjust valves on these engines to .007 intake and .011 exhaust when the engine is cold. The explanation being that the clearances will open up some when the engine warms up or gets to "hot". I always thought the clearances would get tighter as the engine warmed up but my "knowledge" is based on traditional pushrod engines and this is an overhead cam engine. If adjusted cold, will the clearances get smaller or larger when the engine is hot? And is it ok to adjust the valves cold? And how hot is correct amount of hot if I adjust them according to the manual?
View 11 RepliesFord F-150 - 1997-2003 :: 2009 - Removing Cable From Throttle Body?
I busted the cable end by not removing it properly. My question is what is the proper method of remove the cable from the throttle body? Are the cable ends replaceable? If so who has them as a google search didn't find any? I've tried to find written information but haven't any luck. bl2009
View 1 RepliesFord F-150 - 1997-2003 :: Broken Throttle Body Accelerator Cable Connector
So, instead of pushing the throttle cable back and then off, I tried to pop it off and broke the little tab. I've been trying to look for a replacement, but all I'm coming up with is an entire throttle body. Not too bad, but would still like to fix it for much cheaper. It's a 2002 F150 with a 5.4L.
View 2 RepliesCorolla / Matrix 2009-13 :: Throttle Or Gas Pedal Adjustment?
Is there anyway we can adjust our throttle or gas pedal? Cause when I press down on gas, it doesn't open until about an inch down the pedal. Pretty much, I just want the throttle to be more responsive.
View 7 RepliesFord - Mountaineer :: 2000 V8 - Cruise Control Motion Caused Throttle Cable To Bind Up
Mine broke on the throttle body end, I think the cruise control motion caused the throttle cable to bind up as it pulled to accelerate probably over a long period of time. It is a 2000 Mountaineer V8 part is not obsolete from Ford other than a JY what other new sources are there? I was informed only 99-00 are the same from Dealer and have searched via Google. I already fixed it with new 1/8 steel cable and swedged ends, I want a new one just in case liner is gone south.
View 1 RepliesFord Ranger / B-Series :: 1992 - Won't Downshift At 45 To 50 - Transmission Modulator Valve?
So my 92 4.0 automatic has always been kind of a slug since we've bought it with 101,000 miles on it. It's been tuned properly and fuel pump, filter, and regulator been replaced. It runs pretty good but when you're going highway speed or even like 45-50 and stomp the gas it doesn't feel as if it's downshifting. The transmission looks like it may have been replaced or maintained, it shifts good, pulls good. Fluid is clear and clean, no leaks, no burning. I see that it has a vacuum modulator valve but don't know where it hooks up to. I can barely see it behind my catalytic converter. It will have to be removed to change it for sure. But I'm trying to see where the vacuum line goes from that modulator valve. I see the valve but I didn't really notice a vacuum hose coming off of it but again my view was obstructed by the catalytic converter. Would it cause hesitation problems if it was bad or not even hooked up?
View 1 RepliesCelica :: 1992 5SFE Auto Sputters At Half Throttle
My 92 Celica 5SFE 2.2L auto sputters at half throttle. But if I release gas pedal, performance normalizes. I already changed spark plugs cables, ignition coil fuel filter, spark plugs, cleaned injectors, replaced timing belt, engine starts right up and idles a bit high, around 1300 RPM when cold in Park, then when warm 800 RPM in drive. I don't know if it's an electrical issue or a vacuum related issue, spark plugs get carbon fouled after driving like this. I'm tired of having all the newer cars pass me by and my car "running" on 3 pistons.
View 6 RepliesCamry :: Throttle Body Valve Was Stuck Open
About, one month ago my car shut off while driving(pretty scary at the time). I pulled of the road and attempted to start it again. Everything looked good there, but as I was making my way home from work it started to act funny. It would not acknowledge me depressing the accelerator. When I got home, I ate supper, then went to have a look.
The car would turn on, but not acknowledge me pressing the accelerator at all, It did however go up to 30 mph at a snails pace as if it was coasting down a hill. I plugged in my code reader, and it read that the Throttle Body Valve was stuck open. I took it off and tore into to it a bit. I noticed the gears inside the TB itself were corroded and the butterfly valve was locked up.
I replaced the part, and tried to turn my car on with the new TB. All the dash lights are in working order, however upon turning the ignition to crank the engine, the whole car system shuts down. No lights no nothing, besides the car door open sound. The car will remain like this regardless of the key position until I have reset the batter(take off the terminals and put them back on) to which the process repeats itself.
The code reader says no codes are stored because I obviously reset the battery. So now am at a standstill.I believe the old TB froze up, because I had to run in through 3 ft standing water during a storm, and then deployed shortly after(I'm in the service) for a few months while letting the car sit.
Toyota - Corolla :: 2000 - Cleaning Of Valve / Throttle Body?
Car is 2000 Corolla with 60k miles that sometimes has a low idle (sometimes) when driven for the first 15 minutes early morning. Especially when accessories turn on, the RPM drop suddenly to 600 and recovers to 623 then back to 650rpm. After 15 minutes, everything works fine (normal 650 rpm)....my guess is the IAC Valve/throttle body needs cleaning.
What exactly do I need to tell me mechanic? That both the IAC Valve and throttle body needs to be clean? Also, after "cleaning it using a spray"....should he wait till the "spray dissipates"? What happens if it goes inside the engine?
Ford Transmission :: 1981 F100 - AOD Throttle Valve Binding Up
I put a used AOD in my 1981 F 100. The throttle valve seems to be binding up even with the linkage disconnected. There is no pressure on the TV port. The truck will move in all gear positions, but it will not shift.
View 3 RepliesPassat (B5) :: Code P1297 - Pressure Drop Between Turbo And Throttle Valve
Daughters car is throwing this code of 17705 VW (1297) saying it is a "Pressure Drop Between Turbo And Throttle Valve" Car runs rough until about 2500 RPM. Replaced the pressure switch by the intercooler.
View 1 RepliesCamry :: 2009 - Vibrates When At Idle / How To Clean Throttle Body And IAC Valve
I have a 2009 Camry which has the well known very bad vibration at idle when in drive at a light. My Ultragauge shows the RPM are very low when it vibrates. Sometimes it drops to around 425-450 rpm when at a stop light in drive (automatic car). Then it sometimes moves up to around 625-675 rpm and that is when the vibration completely disappears and it is nice and smooth. This issue is intermittent but happens everyday.
Most people think it is due to a bad engine mount and spend money doing that and get no results.
I have done a lot of research and feel it is due to a dirty throttle body and IAC valve and want to test my theory. I will post results once I do the job. What is the easiest and most thorough way to clean both?
Jetta - Volkswagen :: Check Engine Code P0106 / Clean Throttle Valve
VW Jetta SE 2.5L... Took my car to the dealer for a check engine light, the code came back P0106 which states I need my throttle valve cleaned and the dealer also said I need my brake vacuum pump replaced.. Do these go hand in hand? How should I proceed with the dealer? I have only 60,000 miles on my vehicle was there a recall on this issue? The dealer already updated the software in the technical bulletin.
View 2 RepliesStalling - Electrical-wiring :: 1992 Buick Century - Replaced Throttle Position Sensor Still Stalls Out
SO, my Buick has given the code for bad TPS, and it was replaced a little over a year ago...and now after the same symptoms, replaced again.. However, this time, right after replacing, it gave the code again, and still stalls out /doesn't want to stay running especially when put in gear. My regular mechanic also recently just put on a new catalytic converter and a new fuel pump and fuel filter. I'm at a loss, and desperately need my car back.
A little back history...about 3 years ago a 'friend' was to work on my car to install the thermostat and power washed the engine...which shortly after started having all kinds of electrical issues. Right after that, my mechanic had to install a coil, spark plugs, new ignition panel and the 1st tps.
Ford Ranger / B-Series :: 1992 - Hesitation / Starts Spinning Tires Under Full Throttle From A Dead Stop
So among the other annoyances my 92 Ranger 4.0 auto has it has a hesitation before it starts spinning the tires under full throttle from a dead stop. It's the 4.0 automatic. I thought it would have more power than it actually does being use to a 2.5 auto. But this 92 4.0 runs and drives good. I've gotten it tuned up with new motorcraft wires, plugs, new coil, fuel filter, fuel pump assembly, fuel pressure regulator, air filter, idle air valve, new O2 sensor, new Dynomax muffler. I can't find any vacuum leaks. The engine idles slightly rough after you start it up from it sitting for a few hours, but quickly smooths out as soon as you start driving it.
This one here has no EGR. Transmission feels good, may have even been replaced by previous owner before we got it. It shifts good and the fluid is clean and the transmission is the cleanest part under the whole truck. No way of knowing for sure. The truck currently has 111,000 miles and I did all that stuff when we got it at 101,000 miles. So what could it be? I'm thinking a lazy injector or could it be the catalytic converter? Or could it be the throttle body? I know I once had a BBK throttle body on it and it made the world of difference in off the line power but it kept throwing too rich/lean condition and a TPS code so I had to return it. It sucks because it did wake up the motor. I returned it and since then the Check Engine Light hasn't come back on.
Ford 6.7L Power Stroke Diesel :: Steering Box Adjustment Same As Gear Box Adjustment?
I've searched and can only find instructions/details on 6.4L and older Super Duty trucks. The process is the same to adjust the gear box for a 6.7L?
View 5 Replies