Acceleration - Nissan - Xterra :: 2003 - While Accelerating In Cold It Rev And Pause Then Normal?
My 2003 Xterra has been a great car. Few problems until last year I had to have the timing belt replaced (at 120,000 miles no biggie), the day that I got back from Iraq. Well everything has been great since then until a couple of weeks ago I started noticing some acceleration problems. When I press on the accelerator, especially when the car is cold, it will rev, pause, then resume normal accleration. I would like to point out that the whole car pauses, not just the reving. Mechanics seemed stumped and I would rather know what to tell them to do rather than let them dig around and charge me a bunch.
View 1 RepliesNissan - Xterra :: Grinding Noise When Gas Pedal Is At Certain Angle While Accelerating
2000 Nissan Xterra. 3.3LV6 Automatic. 185,000. When I push on the gas pedal while accelerating there comes a grinding noise, but only when I have the pedal in at just the right spot/angle. It shifts fine, and accelerates fine. It runs like normal. However, there is this obnoxious grinding noise. I noticed it a couple of weeks ago, and a few weeks before that, the check engine light was on for TPS/ICV. I had the sensors/valves replaced and it still gives me the grinding noise.
View 5 RepliesNissan - Xterra :: 2003 - Hesitates At Start Up?
I have a 2003 Nissan Xterra, and have been having starting issues for while. Everybody who does a starting diagnostic test says everything is ok and working. Over the past 18 months, I have gotten new battery (charge is fine), replaced starter ( fine), distributor cap (wires, sparkplugs, cap, also fine.) Alternator has tested fine also, have not replaced this yet. The delay seems to be getting slightly longer, but once kicks in car starts fine. I have put too much money into this already to fix problem that has not gone away. Something is wrong and nobody has a clue Side note, no problems with engine, just takes a few seconds to start.
View 2 RepliesNissan - Xterra :: 2003 - Steering Stiff When Turning To The Right
When I make right turns. Its as if the power steering does not work. It is not constant, no issues making left turns, and seems to happen more often in cold weather. About 5 years ago i had a recall to replace the steering column and thought that may have been the issue but took my car in for the recall, they replaced the steering column and still have the same issue.
View 5 RepliesNissan - Xterra :: 2003 - Stalls While Brake Hard
8 months ago i had a blown head gasket and went with a total new engine replacement. I did not use my usual mechanic but another repair shop that had a good reputation due to the price of a the new engine. My car ran well for about 2 months then i started to notice 2 issues. 1) when i applied the brakes hard the car stalled on me and 2) when i put the car in drive there was about a second hesitation before the car would drive. The hesitation (slipping) only does it when the car is in drive gear (auto transmission) and after a few moments of the car runs well even when i park it and restart it the rest of the day.
It only hesitates that way the first time i drive it for the day or if it has been parked for around 4 hours or more. The stalling when i press the brakes hard is constant. I took the car back to the repair shop and they told me my 6 month warranty did not cover that issue cause it was not a engine problem; they said they can look at the car but to even look at it was another $150. I think they are wrong and trying to get more $ out of me so I declined and now my 6 month warranty is expired and i still have the issue. When the car is in idle the rpms are very normal and when driving the rpms are normal. What it could be?
Nissan - Xterra :: 2003 Model Or Subaru Outback 2002 - Which To Go For
I'm looking for a car that is cheap to maintain. I have to have something that allows for interior cargo space.So far, I can find either of these two models for under $8k in clean condition.
I like the Subaru Outback (H6 engine), but I know that more parts can likely equal higher priced maintenance. AWD involves a front and rear differential and a transfer case that can go bad anytime and it has a more complex set up than a basic truck. Then, there's the computery crap that can go wrong.
The Xterra, if I can get a basic 2 wheel drive should, I'd guess, be fairly cheap to maintain, no? Sure, I loose out on the driving advantages offered by the Subaru Outback and gas will cost more.
I love driving the Subaru, but I'm guessing that once a bunch of rattles, leaks, and other issues start cropping up that I might not be so happy with it. The vehicles in my price range are all sitting at 100k - 120k miles. The Nissan Xterra is a truck. It drives like a truck. I might be happier with it, knowing I won't have to pay for high priced repairs. I drive rather conservatively with the intention of keeping my vehicle in good condition. It would be a daily driver for the next 18 months.
Even with higher fuel costs (Xterra will likely get 16-19 mpg), I'm thinking I'd be better off buying the Xterra than the Subaru, yes or no?
Nissan - Xterra :: 2003 - AC Stops Blowing Cold After Driving For A While
I have a 2003 Nissan Xterra 4 clyd. My AC will stop blowing cold air after driving for about 15-20 minutes. The light on the controls is still on and seems to be running. If I turn off the AC switch and let it sit for about 5-10 minutes and turn it back on (can hear the compressor kick on) it will blow cold air again for another 15-20 minutes or sometimes less. If I turn the switch too early the compressor won't turn on. I've checked the levels on the freon and had the thermal amplifier replaced. Also the fan clutch was replaced, which I was told by the mechanic that would fix the AC problem.
View 4 RepliesNissan - Xterra :: 2003 - Grinding Noise Whenever Shift Gears
2003 Nissan Xterra 2.4. It grinds when I shift gears, gears through 2nd thru 5th.
View 8 RepliesNissan - Xterra :: 2003 - Makes Whining Noise At 2200 - 2500 Rpm
03 Xterra makes whining noise at 2200-2500 rpm. Noise goes away outside this range. At 3000 rpm sounds like tachy cable rattles. Have had Nissan check trans, diff, muffler. No luck.
View 1 RepliesNissan - Maxima :: 1998 - Service Engine Soon Light On / Random Misfire?
I have a 1998 Maxima with 57K miles on it. I just bought it about a month ago. Anyway, a week ago I noticed It felt very "choppy" when I shifted into Drive or Reverse. It felt like it was going to stall but it never did. The Service Engine Soon light has been on for about 3 weeks but now, when I go up hills especially, that light blinks. I can still drive it but I shift into Neutral at stoplights to avoid hearing the rough idle while in Drive. Went to Pep Boys yesterday - they had the car for about an hour and then informed me that they would need to keep the car for a full day because of the "complex issues involved" - especially concerning the codes. The codes they read were:
p0300 random misfire
p0325 knock sensor
p0440 evap emission
My car passed smog test abut 3 months ago. I can drive it OK it just is very choppy and so there's not a lot of power, especially going up hills.
Stalling - Nissan - Frontier - Xterra :: 2003 - Engine Hesitating And Stalls Randomly
2003 NISSAN Xterra
Problem started a couple of days ago. While driving the car normally it suddenly stopped. I was able to restart it but it turned off again 60 seconds later. This has gone on with the engine running from 10 minutes to 10 seconds. The battery terminals and all cables are clean. Distributor cap and rotors have been cleaned. Fuel pump replaced last night. I still get the problem. Error codes listed were: P0328 - Pre Detonation (knock sensor) Bank 1 causes could be restricted fuel - over temp engine. Now this error has been coming up for five years and I've replaced the sensor numerous times. P0732 - Gear 2 Incorrect RatioP0102 - Mass Air Flow Low InputP1148 - Closed Loop Control Function, BANK 1P0420 - Catalytic Convertor, BANK 1P0134 - O2 Sensor No Activity, BANK 1
Regarding Fuel Starvation - NOPE, Engine Too Hot (it wasn't), Second Gear Not Within Ratio (never had gear problems), Knock Sensor and most error codes have been related to bank one. Error codes on car computer were erased and engine is still hesitating slightly and stopping. Just checked Mass Airflow Sensor and it looks clean.
Ford F-150 - 1997-2003 :: 2003 - Got Code U1262 - Random Misfire?
I have a 03 F150 with a bi-fuel 5.4 engine an it has 195000 miles. I have had trouble for some time now with misfires. I bought the truck in october of 2011 with 125000 miles and replaced all the coils and spark plugs because it was misfiring badly will running on CNG. It was fine on gasoline and never had any codes. After I replaced the plugs and coils it ran fine on CNG and gasoline.
This summer 2013 it began missing badly at highway speeds only when running on CNG. If I accelerated the miss would go away until I was light on the throttle again.I checked the misfire count and found the bad cylinder and replaced a coil. Then a day later same thing on another cylinder. I swapped a coil from another cylinder and problem went away for a day. Eventually I chased the misfire around all the cylinders on the engine until I had ended up either replacing a spark plug or swapping a coil on all the cylinders. And I still had a misfire. It seemed to be worse on days with temperatures above 90 degrees. Eventually I got it to stop misfiring.
So now 5 months later I am back again with a misfire. This time it is misfiring on both gasoline and CNG and under any throttle conditions, except coasting. I have no codes. And the misfire monitor is sending me around the engine again. I have replaced a spark plug in two cylinders and swapped 4 coils.
I'm ready to buy all new coils, but I want to be sure that it is not a waste of money since the old ones only have 70000 miles on them.
Two days ago I had the misfire monitor saying #4 in the evening and the next day without me having done any work on it it was saying #6. Later that same day it said #7 and I still hadn't done anything other than drive the truck.
I checked the connections at the firewall on the drivers side with the three large plugs that are held in with a 10mm bolt, they looked fine, no corrosion or burnt pins. I checked the connection at the ACFM which also looks good. I will check the connection at the PCM in the next day or so.
Some other problems that may be contributing:
1. I occasionally get a U1262 code (scp fault)
2. Sometimes when I check the misfire monitor it only shows 7 cylinders, sometime 9 cylinders. I am using an Innova 3160 scanner.
3. I have either a leaking valve cover gasket or leaking head gasket, because I have oil dripping from the rear bottom corner of the passenger side cylinder head right above the exhaust pipe.
Chevrolet - Montecarlo :: 2003 - High RPM Random Misfire
Here's the deal with this car i just did head gasket, valve job, all new intake gaskets and spark plugs. Car idles fine and mid throttles fine but with high throttle it wont shift and flashes the random misfire light p0300 it seems to run out of power. I've heard everything from maf sensors to ignition coils and wires. i was just wonder a good place to start and good test to do. I have most testing equipment including scan tool so i can ride with it. o and all cylinders compression tested above 150.....
View 13 RepliesFord F-150 - 1997-2003 :: Random Misfire Now Won't Start
I have a 1997 F-150 2WD 4.6L V-8 that began having random misfires as I would drive. I was planning on going out today to get the new plugs and coils however when I got off work and pulled into my drive something happened when I went to leave the truck wouldn't even crank it just made a clicking noise. The battery has full power (the radio ect. still works). I am hoping that the problem is with the coils and plugs but if not ...
View 5 RepliesNissan - Xterra :: 2000 Stalls And Now Won't Restart
I have a 2000 Nissan Xterra. About a month ago it stalled while I was backing out of a parking spot. When I turned the key, the engine turned over but wouldn't start. A few minutes later it started and I drove it on a long road trip. It was fine until today when it stalled when my husband was going around a corner. He waited a few minutes then it started. Now tonight he started it, drove down the block and it stalled again. This time it won't restart.
View 1 RepliesNissan - Xterra :: Won't Rev Past 3000 RPM In 5th Gear
I can get my car to rev past 4,000 rpm in gears 1-4 but in 5th gear it wont pass 3,000. It used to be fine, but one day it was just like this and hasn't changed since. This is annoying because where I live some of the speed limits are at 75mph. When I'm in 5th gear at 3,000 rpm I'm only going 65. What can I do to fix this? Reset ECU? Clean MAF sensor? Is it related to an approaching timing belt failure (I'm at 94k miles and it needs to be replaced before 105k)...
View 19 RepliesNissan - Xterra :: Only Hot Air Coming Out Of Vents In Interior
My 2003 Nissan Xterra has recently had a few things go wrong up until now I knew how to fix. Now I have only HOT air coming out of the interior vents. It doesn't matter what I do. I turn the knob to cool and turn the AC on and no cold air. I know that cool air isn't being introduced to mix with the engine air. What are some possible solutions and areas to look at.
View 4 RepliesFord F-150 - 1997-2003 :: Truck Has Random Misfire Code
I was involved in a light accident over the weekend. I was hit in the rear by a Prius which didn't do body damage except for the 7 blade harness for my trailer towing. But, now the truck has a random misfire code. You can feel the truck jerk when you go up any grade. We changed the fuel filter and dumped in some cleaner already. One guy says its fuel and one thinks its coils. It is a 2003 F150 extended cab 5.4 with a nearly new motor. The truck has about 175xxx on it and I have had it for about 40xxx. I have not changed coils. We did check the inertia switch on the passenger side and it was not tripped.
View 2 RepliesNissan - Xterra :: Slight Puttering Then Come Close To Stalling
2000 Nissan Xterra 2x4. 185,000 miles. I recently took the car to the mechanic a couple of days ago and had the IACV/TPS sensor replaced. Afterwards I had to tighten the throttle cable because of a grinding noise. Now the car putters slightly, then it seems to come close to stalling. This occurs while idling, while parked and at red lights, as well when driving. While in motion the car shudders and shakes slightly, as if on a bumpy road, but its fresh pavement. While these symptoms occur the RPMs (avg=900rpms) fluctuate; spiking to nearly 2,000rpms then plummeting to 3-400rpms. Notes:
(1) I found that the wire coupling on the distributor was broken (Probably Mechanic). However, the metal prongs for the coupling seem intact (Picture).
(2) Not original distributor (from Cardone Select), I do have the original though.
(3) Spark plug wires are original (old) except for 1.
(4) Spark plugs are a bit old, not that old though I think.
(5) It occurs more often during the cold, snow, and rain.