Ford Super Duty (1999-2016) :: 2008 F350 4X4 - Cargo Light Doesn't Work
I have an 08 F350 regular cab 4X4 that the cargo light doesn't work, Is this powered from the interior light like the old ones? or does it get its power from the GEM module? If it comes from the GEM is it possible to feed it like the old ones from the interior dome light without killing something? I really miss having a cargo light.
View 3 RepliesManual-transmissions - Fiat - Transmissions :: Engine Turns But Doesn't Rev Nor Does It Catch
I've been watching my mother's 1976 Fiat convertible this summer. It had been taken to the shop about 6 weeks ago and it's been running fine without any problems. I had to leave for about three weeks and now the car will not start.
When I turn the key in the ignition with the clutch engaged, the engine turns, but pressing down on the gas pedal has no effect. The engine doesn't rev nor does it catch. There is gas in the tank and clean oil. I checked all the connections I didn't find anything loose.
Ford Super Duty (1999-2016) :: 2010 F350 - Reverse Gear Signal Wire
I installed a reverse camera to my new Pioneer in-dash nav head unit this morning. I wired (at the rear of the truck) the power signal lead to the reverse wire at the trailer connector. I also need to wire a reverse signal input into the back of the head unit. I really do not want to run a power lead from the rear of the truck to the cab. Is there a wire under the dash I can tap into, or could I use the wire going to the backup alarm that’s somewhere under the dash (if I can find it). 2010 F350 deisel, crew cab, 4WD, long bed.
View 9 RepliesSaturn - Manual-transmissions - Transmissions - Sc :: Jumping Out Of 2nd / 4th And Reverse
My daughter's 2002 Saturn S-series coupe has a manual transmission. Lately it has been jumping out of 2nd gear, and occassionally 4th and reverse. What is the most likely cause?
View 2 RepliesAccent LC (2000-05) :: Car Doesn't Want To Go In Reverse And 5th Gear
Just bought a 01 Accent hatch the other day. It's a 5 speed 4cyl. First gear through 4th have no problems. If I try to shift into 5th gear or reverse, the car doesn't want to go into them. The dealer I got the car from said that the problem is with a pin or something. I have never bought a Hyundai before this, I've had old 70s american cars. I was thinking it could be a shifter linkage but I figured I would ask you knowledgeable people about it first before I go and break something trying to fix something simple (hopefully simple.
View 8 RepliesGTI 337/20th Anniversary :: Reverse / 1st / 2nd Gear Don't Work
it all started out like this. i was unable to go into reverse took it to a shop when first and second were good. Came out of the shop after inspection and now i can shift into first or second gear but not the rest, its stuck in those two and they do not work. do i need a new trans or is it a shift fork and or linkage?
View 11 RepliesFord Transmission :: 1989 F350 - Harder To Shift / Grinding Noise Like It Doesn't Want To Go In Gear
I have a 1989 F-350 7.3 IDI with a ZF-5 trans. Lately, I noticed that it was a little harder to shift my truck through gears while driving than it normally is, and when I'm stopped and try shifting into first gear or something it like vibrates and makes like a grinding noise like it doesn't want to go in gear. For a while, I've also had to push on the clutch very hard in order for it to I guess hit the linkage and start, but I never had problems shifting until lately.
Today though, I went to start my truck, I pushed on the clutch as hard as I could, and the switch would not engage so I couldn't start it. So, I guess the switch was farther to link than the pedal could possibly go. I went under the dashboard and engaged it by hand then it started. I drove home and the shifting was still iffy. How can I make the switch engage normally again so its closer I guess and so I don't have to push so damn hard on the clutch to get it to start? And could the switch linkage have anything to do with the shifting being funky lately, or could that only be the clutch itself?
Chevrolet - S-10 :: 2003 - Loud Grating Noise / Reverse Gear Would Not Work
Not really even sure how to explain this problem. The other day while driving the car made a loud grating noise, which would stop if I kept giving it gas, but would persist while braking or simply slowing down naturally. This continued until I reached my destination (drove fine), but when I got home, my reverse gear would not work. I tried putting it into 4wd, and reverse worked again (and also in 2wd). What on earth is wrong w/ my truck?
View 1 RepliesCorolla / Matrix 2009-13 :: Toyota Automatic Gear Reverse Lights Don't Work After New Stereo Installed
Toyota corolla 2013 automatic gear reverse lights don't work after I installed new stereo it's my fault i shorted 12v positive backup (reverse) light trigger camera stereo v12+ cable to ground while backup (gear R) in place. As a result reserve lights don't work beside gear indicator doesn't show on main screen. I can drive without problem but problem still intact.
I checked all fuses and they are all okay I need to identify problem or possible repair too I only find 2 fuses behind glove box i think they call "instrument panel" there are bunch of cable and underneath of cables there is only 2 rectangle shape fuses I could not see anything else, the other fuse box is in engine compartment i thoroughly tested each small fuses they are all okay is there anything else i forgot to check ?
I attached also instrument panel screen shot ....
Toyota - 4runner - Wheels - Transmissions :: 2000 - Right Rear Wheel Doesn't Roll
I have a 2000 Toyota 4 Runner with 115k miles on it. While in Colorado a month ago, we were driving down a snow covered hill and some guy banged on the window telling us the right rear wheel wasn't spinning. We put it in reverse and it rolled fine that way but still didn't when we headed back in drive. I goosed it a little bit and it went "bam" and drove fine after that.
We were in 4 wheel drive at the time. Last night it happened again. I put the vehicle in drive and it wouldn't budge. I goosed it a little again and it went "bam" and drove several feet until I stopped. It froze up again for a few more minutes. It was NOT in 4 wheel drive this time. Is it time to dump this thing or get a new transmission in preparation for the inevitable?
Ford 7.3L Power Stroke (1999-2003) :: Truck Starts And Runs But Throttle Doesn't Work
So I installed my chip today. It's got anti-theft, high idle, stock, 50, 75, 100 tunes.
With the chip installed the truck starts. In all tunes except "High Idle" it idles at about 1000... normally it would be like 500-600. High idle position works (1100-1200 RPM). Anti-theft position works - it kills the truck. The throttle does nothing when pressed no matter which position it is in. Stock, 50, 75 or 100.
I removed the chip and the truck runs fine. Did these guys send me one for an automatic? Or do I have the wrong computer in my truck? My computer code is DAC3 and the truck is a 2000 with a manual transmission.
Starting - Electrical-wiring - Transmissions :: Nissan Maxima Cranks Slowly Then Turns Over But Doesn't Move
Just recently bought a 07 Nissan Maxima SE. Has a few issues.
The car sun roof does not work at all. It worked the day I bought it though.
Has issues turning on. Cranks slowly then after a few seconds of struggle it turns. Didn't have this issue when I bought it.
Goes idle when first starting to drive. From park, I put the car in drive, or reverse, and let go of the brake, it basically does nothing. Engine is on as if it were in park or neutral, but the car doesnt move. When I press the gas it takes a few seconds before it decides to actually move.
Saturn - Transmissions :: 2003 Car Only Goes In Reverse Even When In Drive Or Neutral
Have a 2003 Saturn Vue with a variable transmission (rebuilt). It will only go in reverse even when in drive, or natural.
View 5 RepliesToyota - Camry - Transmissions :: Stalled When Put Car In Reverse While Driving
During our last ice storm during a nice long skid down an icy hit, I reverted suddenly back to my days one decade ago of driving a stick-shift in the ice and tried to down-shift our '98 Camry (automatic). I placed it in reverse. It stalled. The car continues to run, but the check engine light came on. I took it into the garage and they couldn't find any engine issues. They turned off the check engine light. It came back on the next day. Sometimes it sounds like the gears aren't shifting automatically as I drive (rpms run high.) Am I damaging the car by continuing to drive it?
View 3 RepliesFord Super Duty (1999-2016) :: 2003 F350 Won't Start / When Turn The Key It Just Clicks And Doesn't Crank
So I 2003 6.0 F350 that is a Dually. Been sitting in my yard for about two years now. I turn the key it just clicks and it doesn't crank. The starter solenoid is not on the firewall so I use the trick with the battery connected positive straight to the starter with the whit The starter solenoid is not on the firewall so I use the trick with the battery connected positive straight to the starter with the wire on the engine bay. It cranked for a while and that started ran rough. Then it just died. I did not start again. I did this during winter so the engine have time to cool off it was about below freezing. Done this multiple times and drove up and down in my backyard but not on the road. What could be wrong with it. Either way I put in diesel 911 and more fuel but and I change the filters with Motorcraft OEM filters. Sure that the caps were right.
View 14 RepliesFord Super Duty (1999-2016) :: Steering Absolutely Doesn't Work When Stop The Truck With Foot On Brake
I'm sure this is a common issue, but I don't know exactly what to search for. I have a 2001 F250 7.3L. When I stop my truck, with my foot on the brake, the steering absolutely doesn't work. I replaced the PS pump, which it needed, plus all the hoses and it got better, but the no steer problem while braking is still there. I have seen that an upgrade in pressure hoses may work?
View 1 RepliesFord Transmission :: 1999 F350 - 4R100 Won't Go Forward But Has Reverse?
I don't know why... It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problemo, then when put it in Drive it revved like it was in neutral.
There was no banging, no clunkin, nothing to make it seem like something catastrophic happened. I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more.
Next I did the obvious and checked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new. I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
I am on a tight budget and working on my back. I am willing to take the tranny out and bring it into town. Personally I think it's electronic but I don't know ...
Why THis thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings?
Can this be a "worn out" valve? or gasket issue? I really want to avoid removing the tranny at all costs so if there is something I am missing let me know and if you think just yank it out I will.
Subaru - Outback - Transmissions :: Car Won't Move In Drive, Reverse Or Neutral
When I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
Ford Super Duty (1999-2016) :: Reverse Lights Dim Or Don't Work At All
I have an 02 f350 XL. The other day it rained and all of my rear lights went haywire. All problems are out back.
- Step on brakes, high mount, and lic plate lights light up with brakes.
- Turn on marker lights and the high mount lights up and the tails and lic plate lights dim.
- Marker lights on, apply brakes, and the tails and lic plates lights go out on bed, high mount activates.
- Use turn signals with markers off and all of the rear lights including high mount flash..
- Reverse lights dim or dont work at all.
I have tried a new MF switch, checked all fuses. cleaned rear frame ground. took apart brake switch and cleaned it. non tilt column but checked wires. replaced flasher. unplugged brake light switch and headlight switch, problem is still there. removed trailer relays, no luck. checked all chassis plugs. disconnected TRS.
I should mention i have 12v cummins swap and a pcs with standalone harness. no problems over the last few months since swap until it rained last monday.