Yaris/Scion & Vitz :: 2000 Toyota Echo Drives Fine Until Warmed Up
I have a 2000 Toyota Echo. Symptoms are, the car drives fine until warmed up. Once warmed up, about 10 min or so, there is surging, an inability to maintain idle, periodic loss of brake assist, all consistent with my p1349 code. This happened about two months after I changed my oil (the old oil was in there for an embarrassingly long time). I ran motor flush and again changed the oil; symptoms persist. I have removed the OCV and OCV screen; both look fairly clean. Here's the question: what checks can be done on the OCV itself before I call a bad OCV and replace it? The service manual was of only marginal quality in explaining any checks.
View 2 RepliesPrius (2001-03) :: Clicking In Front End When Taking Off Either Forward Or Reverse
When just taking off, either forward, or reverse, there is a clicking sound, like a rock in a hubcap, but very soon, stops, actually I had the tire off the car, and turned the rotor as fast as I could, by hand, which was really slow, and the clicking was there, just for a few seconds. I thought maybe the rotor was rubbing on the dust shied, but that doesn't seem the case. When I have the window down, I can hear is slightly, not very long. When I had the tire off, I checked the cv joints, no torn rubber, no grease flying around, I pushed in/out, up/down on both ends of the shaft, nothing seemed out of the ordinary. The only thing I did notice was the strut rubber, bellow, was torn on both side, and looked like some oil was leaking, so I will have to replace both struts soon, but I don't know if that would have anything to do with the clicking sound. Like I said before it sounds like a BB in a hubcap, but in a sense that doesn't make sense, because the sound stops way before centrifical force takes over, know what I mean??
View 1 RepliesSanta FE SM (2001-06) :: Transmission Go Into Reverse Just Fine But Would Not Move In Any Forward Gears
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 RepliesDodge - Transmissions - Grandcaravan :: Shifts Just Fine Going Forward But Will Not Move In Reverse
I am considering buying a 1999 Dodge Grand Caravan with a reported transmission problem. Mileage is around 120k, and the price MIGHT be reasonable even if a trans rebuild would be necessary. I have not seen the vehicle yet, so I'm not yet committed to anything.
Seller claims the car shifts just fine going forward but will not move in reverse. Is this immediately clear that rebuild is going to be necessary? Are there less invasive repairs possible such as valves or controls or other parts which might solve this problem?
I suppose a Caravan transmission at 120,000miles is probably nearing the end of its lifetime, at least that was true of older ones. But like I said, the price is low enough that the cost of a rebuild might be justifiable if all else about the vehicle looks good. I want to have a better sense of the prospects before I invest time in going to look at this...it's about 50 miles away. I have a local transmission shop that I trust and which has reasonable prices
Ford - Explorer :: 2002 - Windshield And Side Windows Taking Forever To Clear Up When Foggy
I got an 02 explorer xlt with the manual heater control and I've noticed now that it's getting colder it seems like my windshield and side windows are taking forever to clear up when they are foggy. When I put my hand up by the window or the vents for the driver/passenger side windows there's barely any air movement, and that is even when the blower is on the maximum level.
Another thing I've noticed is if I set it to floor only, it blows out the defrost. Same for the defrost only, I can feel some air blowing onto my feet. So what to look for when I pull this into a garage and start to looking around. I also changed the coolant and put in a new thermostat about a month ago, if that's of any importance.
Ford Super Duty (1999-2016) :: 2004 F350 - Loud Clunk Noise In Forward Or Reverse Hi Or Lo When Accelerate
Ive got a 04 f350 that after u shift into 4hi or 4lo when u accelerate it it makes loud clunk noise in fwd or reverse hi or lo. With hubs unlocked it still clunks. Have checked, wheel bearings, axle U-joints, and driveshaft joints all good. So I am thinking I've got issues in t-case. Popped drain plug out and wow that dex merc 4 looks nasty. So thinking I need exploded view of transfer case.
View 4 RepliesHonda - Accord :: 2012 - When Accelerate V6 Takes Forever To Get To 40 Mph Unless Floor It
I bought a new Honda Accord v6. I drove it off the lot with 40 miles on it. The acceleration was fine when I bought it.
It now has over 500 miles on it, and the acceleration is terrible. When I'm at a stop light and the light turns green, it takes forever to get to 40mph unless I floor it. Honda Civics pass me at every light.
What could be the problem? I'm very concerned.
Toyota - Corolla :: 2002 Idles Fine But Bog Down On Acceleration
Just as the title says, 214k great shape just wont get going more you mash the less it goes.... fuel pump already replaced, can undo battery and take a while to reset feels to do fine then goes back to bogging down... TPS ? idle air control?
View 3 RepliesCorolla :: 2003 Toyota Developed A Sound While Driving - Idles Fine
My 03 Corolla S - 5 Speed has developed a sound while driving, only when giving it gas. The sound goes away when I press in the clutch. It doesn't make any unusual sounds while parked and idling.
The sound, sounds like a knocking noise. At least to me that's what it sounds like. My car has 156k miles on it.
The car idles fine, rpm's are good on while driving, temps good and still gets really good gas mileage.
Does it have something to do with my clutch, since the noise goes away when I take my foot off the gas, or press the clutch in?
Is there something I should be checking? All my fluids are good, brake/clutch, oil, transmission fluid, radiator, etc.
Toyota - Corolla :: 1995 - Intermittent Stall, Battery Light Comes On But Restarts Fine
330,000 km on car. I drove 45 minutes when battery light came on on and car engine stalled when making a left turn (fuel light had just come on too but not empty) and restarted on own, drove 10 minutes and it stalled again, so I pulled over and restarted. Drove 45 minutes home. No issues since. Shop says 10 year old battery and alternator are testing fine, though they suggest replacing alternator as it may be going. Could there be other electrical issue since the issue is more intermittent? Car would not stall immediately if alternator failing I would think - should run on battery for a bit and not restart. Drive maybe 400km per month and it sits for 10 days at a time.
View 4 RepliesCorolla / Matrix 2009-13 :: 2010 Toyota - AC Works Fine When Car Is Moving But When Idle It Gets Warmer
I recently bought a 2010 Toyota Corolla. I have been having some issues with the A/C. The A/C seems to work fine when the car is moving but when it is idle it gets warmer. I have recently gotten the freon checked and they put in some more but that didn't work, same problem still happening. Somebody told me that i need a extra fan which didn't make sense to me. Last resort will be to take it to the dealership to have them check. Once again the A/C blows cold air when the car is going over 50 MPH.
View 2 RepliesToyota - Corolla :: 1990 Wagon Just Stopped Moving Forward After Jerking Back And Forth Several Times
While driving our 1990 toyota corolla (3-speed automatic transmission) on the freeway recently, the car gave a slight jerk, at which point my husband looked at the gas gauge and noticed it was well below "E".. Oops. fortunately, there was an exit right there with a gas station. Filled up and we were off toward the next on-ramp. Got to about 35-40 mph, and all of a sudden the car literally just stopped moving forward after violently jerking back and forth several times. We then tried to put in neutral and push it to the side, but it wouldn't even do that. Everything was locked up, seized solid. Somehow we managed to get it to the side.
The flatbed tow truck took us home, and all we could do by that point was move a foot or two in reverse after it dropped us off... fast forward... After several days/weeks of it sitting around we can now actually drive it forward! reverse! but we haven't taken it out of the driveway to go more than 5 mph.. We had seen some fluid leaking prior to this incident, but could NOT figure out where it was coming from despite checking obvious fluids meticulously every couple of days. A friend said it might have been the diff fluid? We'd like to fix the car, but to repair a tranny on this old car (although it only has 67K miles!!!) is too expensive. My husband wants to make it a weekend project.
Toyota - Corolla :: Choking Out When Accelerate Quickly
My 1996 Toyota Corolla has started sputtering (choking?) out when I accelerate quickly (like getting on the highway) or when I get up to about 70 mph. Is this a symptom of a clogged fuel filter or a bad fuel pump? If so, is there a way to tell which it is before taking it to the mechanic? Or could it be something else?
View 11 RepliesToyota - Corolla :: At Idle Car Runs Very Rough But Can Accelerate Up To About 50 MPH
I have a 2000 Corolla with about 147,000 miles. At idle it runs very rough, but can accelerate up to about 50 mph. Then it starts to cough and wheeze and run roughly again and won't accelerate any further. It feels like the engine will shake itself off its mounts, so I slow down and stay under 50 mph. I replaced spark plugs and a repair place hooked it up to a computer. They then told me it needed about 1800 dollars worth of repairs to replace the valve cam I think they said. I'm skeptical and wonder if it just needs a tune up, . It has not had one since I bought it at 128,000 miles, and II don't know how long it had been prior to that.
View 5 RepliesToyota - Corolla :: 1991 Won't Go Into Reverse?
My husband's 1991 Toyota Corolla goes into reverse when he first starts it in the morning but...then it won't go into reverse the next time (same day) he tries to start it.
View 2 RepliesGolf IV R32 :: In Cabin Noise When Accelerating / Deep Metallic Grind Noise But Car Drives Fine?
I've been working on my car for a few weeks now and I've been doing my best to figure out. The source of this sort of 'metallic grinding' that I'm hearing within the cabin. I cant seem to pinpoint where it's coming from within the engine bay with the hood open (maybe due to the magnaflow exhaust diffusing the sound from the outside of my car). I can easily hear noise when I'm inside however with indications its coming from the lower central area of the engine bay. I drive an '04 Volkwagen GTI 1.8T
In the days I've been working on it I've replaced the:
1. Timing Belt (and tensioner pulley/tensioner dampener)
2. Water Pump
3. Serpentine Belt
4. Thermostat (and housing)
5. Clutch disk and flywheel (from a SMF to a LUK DMF clutch)
6. CV Axles (both drivers and passengers)
7. Clutch Cylinder Slave
8. Wheel Bearings (front left and right)
9. Rotors (Front Left and Right)
Diagnosis**
The car starts without any problems just as it use to prior to the replacements done. BUT it's once I get the car moving where I begin accelerating I start to hear a dull grinding noise/rumble that becomes more and more apparent the faster I go. It seems the sound is directly correspondent to wheel movement upon accelerating. Nevertheless I could be wrong.
I had a friend tag along to diagnose the sound and to him it sounded similar to the "tunneling of air not being properly sealed" but to me it sounds like a metallic grind. My friend also mentioned that he felt it was louder towards the passenger side in contrast to the drivers. As mentioned before the sound is reproduced anytime wheel movement occurs. I've checked torque spec for every replacement job done to the car so there are no loose bolts/nuts/brackets. (but there are exceptions, which I will get to).
Knowing that I've replaced both of the wheel bearings (and hub assembly) I can only assume the sources isn't from there. But I do admit a few mistakes while I had the car on jacks.
1. During the timing belt replacement I thought I would need to remove the exhaust (because I felt it would interfere with the lowering of the engine) so I, (without success), tried to remove the connection between the "bend of the exhaust" to the manifold which were 4 'turbo studs'. I had the worst time with the removal of studs but I was able to impact one them off, and as I tried another the strength of the impact broke one them half way through (meaning that I was able to unthread it a few threads but it snapped in the process, so I would need to somehow drill it out in order to replace it). This is where I gave up and did my best to install the one I had removed. Which I could only get threaded half of the way in.
-All in all I have 1 broken stud that still making a connection, and 1 protruding stud out of the 4 that connects the exhaust to the manifold.
Question: Can this be the cause of the sound? Without the full connection of 4 studs bolting exhaust to the manifold? Can this be the sound That my friend was referring to as the "tunneling air not being properly sealed"?
2. The second "mistake" isn't necessarily a mistake but a fault I found later that has to do with the Passenger CV Axle. I read a few forums here and read that it could be a problem with the axles, so I put the front end on jacks once again and found that there was a bit of movement of play on the axle shaft itself. In detail, the 2 connection points for the axle both at the Output differential flange and Hub assembly are secure and torqued to spec without any loose bolts.
BUT the rod itself seems to shift about a 1/2" between these two connecting points.
Question: Could THIS be the problem? With this type of 1/2" shift in the rod is it possible it can recreate the dull metallic grinding I'm hearing so much?
Toyota - Corolla :: 2010 LE - Random Rapid Gunfire Noise When Accelerate / Decelerate
I have had my Corolla LE since October 2011, there has been no maintenance issues whatsoever with it, and it has 65K miles on it. Up until September it was a solid, quiet ride, and with the passing two months, what started to be a quiet vibration, has grown louder and louder. At first I thought it was something inside one of my storage compartments rattling, and then I thought it was the blower, only noticing the sound when I turned on the heat. Now, it makes noise when I accelerate, decelerate, at a complete stop (with the car still on). I read another post about it might be the heat shield, and I was convinced previous to reading that that it was something exhaust-related. But, I'm not sure. This noise has gotten louder, isn't consistent with any function of the car, it appears to be random, but the noise is still the same, the quick "drr, drr, drr" noise, truly a rapid gunfire sound.
View 5 RepliesToyota - Corolla :: While Shifting Into 4th Gear And Accelerate The RPMs Drop - Power Loss
I have an 05 corolla XRS. I just had a sport clutch put in about 1 year ago. Whenever I shift into 4th gear and accelerate, the RPMs drop about 500 and I lose power for about 3 seconds before it starts going back up. Other gears are acting normal. Best part is that I let my friend drive the car earlier and since he did it's been doing this.
View 7 RepliesCorolla / Matrix 2009-13 :: On Long Drives, Seats Become Uncomfortable
I have a base model 2009 Corolla and I find that on long drives (anything over an hour) the seats become incredibly uncomfortable. I have developed back pain I did not have before I bought the car. My wife drives an 05 corolla and I have no problems with it (even on 5 hour drives) so I can only assume that Toyota cheap out on the newer generation's seats. I have tried many different cushions, lumbar supports, and seat heaters, but none of them work all that well. Adjusting the seating position does not work either. I installed cruise control and while that worked a bit, it was no solution.
View 14 Replies