Subaru - Outback :: 2002 - Slow To Accelerate When Going Into Right Turn
I have a 2002 Subaru Impreza Outback Sport with ~140,000 miles on it. Recently, it's started having a problem, where when I make a right hand turn, it fails to accelerate until the wheel is straight...as if it's revving but not catching/accelerating until I've straightened the wheel and am headed straight onto whatever road I've just turned onto...does that make sense?
It tends to happen more at 1st start up in the morning...and then, once its warmed up it's not as bad, but still present. Left hand turns I don't notice it...maybe because they aren't as sharp? Also, fyi, the check engine light has been on for a while, but I know this is due to the catalytic converter..and am saving up to get that replaced.
Subaru - Outback :: Overheating While In Stop And Go Traffic And When Accelerate
I have a 2000 Subaru Outback with a little over 162,000 miles. About 3 years ago I had the head gaskets replaced. This past March the car started over heating while on the highway driving back to Boston from New Jersey. It has been doing this intermittently since then, and I have had two mechanics look at it.
The first mechanic, who is my beloved mechanic in Maine (where I am originally from), checked the sensors and relays. He even replaced the relays for free, and it still overheated on the way back from Maine to Boston. Needless to say I did not give him enough time to really look at my car to figure out the problem.
I then went to my back up mechanic in Boston, who kept the car for about 4 days. He said there are no leaks and the car did not actually over heat while with him. He had one of his guys drive the car home at night and back to the shop in traffic in the AM, and had it run for hours while on a lift, and on the ground. Still no overheating. However, he did say that the car was eating up coolant, which indicated to him that there might be a head gasket problem.
I was a little upset by this diagnosis because I had them replaced already, and also because I am getting married this summer so this obviously is not the right time to be buying a new car. I should mention that both mechanics looked at my car at the end of August. I have still been driving and watching the coolant.
The car is still randomly overheating but i tend to notice it happen more while in stop and go traffic and when I accelerate. The needle will go all the way up to red, stay there for a few seconds and then slowly creep down. This happened this morning, and I had checked the coolant yesterday and it was full! I checked it again at lunch time to see if it had used all the coolant during rush hour and it was still full. This chain of events seems to keep happening and I constantly check the coolant. Since August I have only had to fill it once. I have also noticed that when I open the radiator cap the coolant is not sitting level like I've been told it should. I've put a decent amount of work into the car and everything else runs perfectly.
Is it possible that this is a pumping or air bubble problem, and not a head gasket?
Subaru - Outback :: Shuddering Frequency Increasing When Accelerate From A Stop
Over the last several months, the frequency with which my 2007 Subaru Outback is "shuddering" when I accelerate from a stop has been increasing. It feels like driving over a cattle grate -- a vibration that lasts for just a few seconds, and occurs in the 35-45 mph range. Now is happening on a daily basis, a couple of times per day. Based on some internet searchers, I concluded this might be a torque converter problem. Took it to the mechanic today and, of course, couldn't reproduce the problem with them present. They replaced the transmission fluid with a synthetic fluid and replaced the transmission filter.
View 8 RepliesSubaru - Outback :: 2001 - Rattle When Accelerate And Takeoff From Dead Stop
I have a 2001 Subaru outback. Recently I've noticed a rattle when I accelerate, especially when I take off from a dead stop. I sounds like it's coming from the front wheel area. It also occurs sometimes when making a turn and then accelerate. It almost sounds like an object in a box and someone is shaking the box-very noticeable.
View 3 RepliesFord Transmission :: E4OD Will Not Accelerate Past 15 MPH
1994 E350 Club Wagon 351w, E4OD Transmission. New MLPS, New VSS, New TPS, New Fluid, New Filter, 5 year old Torque Converter.
The Transmission dribbled a little bit from the front pump seal a couple weeks ago, I checked the level, it was a bit low. Topped it off with Lucas, the dribble stopped. I drove it successfully for another week. I took it on a 10 mile trip, and 5 miles in, it started slipping above, 35mph, I let off the accelerator, and the transmission "Caught up" and I drove 35mph the rest of the trip. I let it sit over night.
The next morning it acted as if nothing were wrong. I drove it some more, and the same thing happened. I parked it, and revved the engine up a bit, and it tried to MOVE in park, I put it in neutral and revved the engine, and it lurched as if it were still in 1rst gear.
This time I let it sit for 24 hours, and after work I successfully put 20 miles on it without missing a beat. It was shifting right, good solid connection between the gas pedal and the road, and I thought the problem was fixed, as the temperature the day before was -20, and it warmed up outside to 30 degrees above.
I parked it for a couple hours and went to go do the errands, and it wouldn't make it above 15mph. It even struggled to do that much. I put it in reverse, and it held great, no slipping at all.
Let it sit until the next morning, and it was better. I pulled the Codes, and it gives me a 63(7) TOT High, and a 62(9) Torque Converter Clutch. It may or may not be relative, but Cruise hasn't worked in about 6 months either. What am I missing here? What could possibly causing this trouble? Fluid is up and new.
Ford - Mustang :: 1992 - Shaking And Won't Accelerate Past 40 Mph
I have a 1992 ford mustang 4 cylinder,its messed up bad.my car is shaking bad all the time and will not go faster than 40mph.what is wrong??
View 19 RepliesPassat (B5) :: EPC And Caution Signs Displayed When Rev High / Does Not Accelerate Past 80 Mph
My car is a 2005 1.8T Passat; About two weeks after replacing a burnt spark plug coil the vehicle started displaying EPC and a caution sign embedded in a circled arrow, whenever this happens i discover the vehicle does not accelerate past 80 mph even when the throttle pedal is pressed to the extreme; I replaced the engine speed sensor all to no avail, a used throttle body also behaved same way, what is responsible for this and how to rectify the problem?
View 1 RepliesEngines - Gasoline - Repair :: Mercury Cougar Won't Accelerate Past 40 MPH
93 Mercury Cougar 3.8L V6 with just over 83,000 miles
l've been trying to figure out this issue for ages, but can't seem to find the root of the issue. When driving and accelerating to 40mph, the rpms drop and GET STUCK at exactly 1000rpm. Forcing the accelerator down makes the engine bog and sputter and not go any faster. No check engine lights whatsoever.
The idle is very rough and low in park (700rpm compared to the regular 900) and very low in drive (500 compared to 650-750). When stopped in traffic for a while, it begins to shudder and shake like it wants to stall right there. Now let me run down the extensive list of parts l've thrown at it, bringing only temporary results:
Replaced catalytic converter
Replaced IAC valve
Replaced O2 sensors
Rebuilt transmission (runs great, so l've ruled that out)
Replaced 1fuel injector
Replaced MAF sensor
Replaced motor mounts
Cleaned throttle body extensively
I asked a guy at a Firestone and he said that l needed a valve job. Asked another guy at another place, he said l needed a fuel system cleaning. Asked another guy under a tree, said l needed a new speed sensor. What could be the root issue? l was thinking carbon build up over 22 years maybe? Almost all 83k of those miles have been city miles...
This car is my baby, all l want is for it to be able to handle highway speeds without a hiccup. l'm keeping it and plan to see 100k hit the odometer and many more miles!
Golf IV / Jetta IV :: 2001 / 1.8t - When Accelerate Boost Won't Go Past Zero And Stutters
Okay I have a 2001 Vw Jetta 1.8t Wolfsberg.
I have done a few mods:
- Oil catch can
- Boost gauge
- New turbo (5000 miles old)
- Brake booster mod
- PCV system fixed and some hose deletes (that make the intake manifold have one line off of it rather than two)
- Timing belt/ pulleys
- Accessory belt / pulley
- A few other things but nothing to cause this
The car will do this randomly. And I mean once every two weeks of that. I will go to accelerate and the boost gauge says the "boost" is at zero and no matter how much I give it gas, it won't go past zero and stutters. But it stops almost as fast as it starts. I don't get it...
My catch can has 3/4" line to about 1/2" or so, that meets the oil catch can. (Ebay with the blue hose.) I have new plugs, all new (dealership recommended) lubes, all kinds of new small odds and ends. But it's never done this before. (3rd time now in a month..)
Ford - Explorer :: 2004 V8 Engine Won't Accelerate Past 1800 Rpm
It's a 2004 4wd 4.6 v8 with 140,000 miles. My wife was driving around town today and had to park it at her daughter's house because even if you floor it,the engine will only rev to about 1500-1800 rpm's and idles really low,maybe 600 rpm. she said right before it started running bad,there was a bad smell. Also there is a humming/rattling noise that sounds like it's coming from the upper intake/throttle body area. I went and looked at it,tried to pull codes.
The check engine light isn't on and there are no codes stored in the computer. A couple of days ago,there was code po420 (Catalyst System Efficiency Below Threshold (Bank 1)and the check engine light was on. Engine was running fine. I cleared the code,and it never came back. I am not sure this is related,just trying to give all info possible.
Honda - Accord :: 1997 - Water In Radiator Oily / Won't Accelerate Past 20 Mph?
I'm driving a 97 Accord SE and it's suffering from a few issues that have me worried to say the least. For one, when I filled the radiator with water I noticed that it was cloudy/oily. Something was definitely in there with the water.
Two, I foolishly drove it thinking it would be fine. After 50 feet or so however problems started happening. I couldn't accelerate past 20mph. If I tried by putting my foot down on the gas nothing would happen but the RPMs going up. Each time I started the car I could go a little ways before pushing on the gas did nothing. Then I would have to restart the car in order to get anywhere with it.
Some background, I got my oil changed today after going about 1000 miles over when it should have been changed. Also, when it was scanned in the past the error code 0420 showed up. That has something to do with either the catalytic converter running rich or the O2 sensors above and below it might be broken.
Impala - Chevrolet :: Sputter And Jerk When Start To Accelerate Past 25 Mph And Get Around 2000 Rpms
I have a 2002 Chevy Impala driving it in the city of Chicago. It's recently had the oil changed, and the transmission fluid flushed and filter replaced. This car was mine before I went off to school, and I meticulously maintained it for three years, and then my step sister inherited it. She drove it for two years, and then it sat in the driveway for a year and a half. It's got about 175,000 miles on it.
Problem: Every time I start to accelerate past 25mph and get around 2000rpms, the car starts to give out, sputter and jerk. It starts to drop off right when it should be shifting to second gear. When on the highway, even if I floor the gas peddle, it won't accelerate normally, but instead just crawls slowly to higher speeds.
It will eventually reach the higher speeds, but it takes about 5-10 minutes for it climb up from 25mph. I don't know enough about this level of car trouble to make a diagnosis myself, and would like an estimate of the cost for repairs. Also the car is getting around 19mpg on the highway, which I need to improve if I'm going to survive the $4.50/gal of Chicago gas. I'm hoping that fixing this problem will take care of that as well.
Ford - Mustang :: 2003 - Pingy / Tingy When In 1st And 2nd Gear And Accelerate Past About 2.8K RPMs
I have a 2003 Mach 1 Mustang, ( 4.6 DOHC 32 Valve)....
When I start my car in the morning. Idling the car sounds normal and perfect with my SLP exhaust. But when I start to go on my merry way, when I’m in 1st and 2nd gear and I accelerate past about 2.8K rpm's. I hear a really quite noticeable pingy/tingy sounds from my engine (Yes sounding like that annoying AMMCO commercial with people making noises). This will continue for a little while when i get into my normal running temperature, the sound isn’t as "Loud" so to say but still present.
I can comfortably say that there is nothing loose within the engine compartment. My spark plugs are tightened to the proper amount. I experience no performance lost as well. This has just been a nuisance since I have purchased the car, it currently has almost 60k mileage and has followed the proper maintenance.
Subaru - Outback :: 2000 - CEL Came On?
My 2000 outback wagon has only 67k miles. About a month ago, the check engine light came on. I took it to an Auto Zone and although unfortunately I didn't write down the code, the person who checked the car seemed to think it was probably just a bad tank of gas. I ran through that tank of gas and filled up with premium gas. Light didn't go off until THAT tank was near empty. Filled up a third time and light remained off until tank was near empty and it came on again. It has not yet gone off. I'm not sure how many more tanks of gas I should run through! The car isn't running poorly so I thought the bad gas was a good explanation.
A side note: about 6 months ago I had to have the head gasket replaced. I argued with Subaru and got some extra work done in exchange for the head gasket payment since my car missed the recall by a few digits but I was obviously stuck with an inferior product. I'm hoping they didn't do an inferior job. Even though it was 6 months ago, it wasn't that many miles ago - you can see my the year/mileage on my car that I don't drive a lot. Does that gas explanation sound reasonable? Anything about a head gasket related?
Subaru - Outback :: Corrosion Of Tie Down On A Battery?
Having problem with corrosion of the tie down on a battery? The terminals are fine. It's just the metal plate that holds the battery in place with bolts. The paint has corroded off. I clean it up and cover it with dielectric grease. I have to do this every 4 to 6 months or so, because the corrosion keeps coming back. I had the same problem with my 2004 Subaru Legacy, and had to replace the battery holder as a result.
View 1 RepliesSubaru - Outback :: Car Seems To Be Loosing Coolant
my car has tge 3.6 motor and has 2500 miles and seems to be loosing coolant...
View 2 RepliesSubaru - Outback :: Cooling Fan Always Remains On
Our 2011 Subaru Outback 3.6R, which we bought brand new back in Feb ’11 and only has 4k miles, seems to be having issues with the cooling fan. The cooling fan will come on when the engine is cold and it will stay on the entire time the engine is running. I’ve read that the cooling fan will run the whole time when either the A/C is on or the vent control is set to defrost, regardless of whether the engine is cold or hot. In my case, the cooling fan comes on when the engine is cold, even with the HVAC off and it will remain running at full speed when the engine is running, again with the HVAC off.
Every time I go to start the car after it has been sitting for an entire day and the engine is cold, when I turn the key to the “On” position, before the engine is even started, the cooling fan comes on. How is this possible when the engine isn’t even running and the engine is cold. Again, the HVAC is off. Once the car is started, the cooling fan will remain on until the car is shut off. The fan is running as such a high speed you can hear it over the noise of the idling engine. Once I turn the car off the fan shuts off.
Since we’ve owned the car there were two other issues First, the transmission pan gasket wasn’t properly installed and it was leaking transmission fluid. That issue was fixed and is good now. The second issue was that oil was leaking from the timing chain cover. It turns out that the timing chain cover gasket was also improperly installed. This too was fixed, and doesn’t seem to be a problem anymore.
Subaru Outback :: 2012 - Stalling Out After Getting Gas
I purchases a 2012 Subaru Outback i2.5 Premium in January. The car has been stalling out after getting gas; I've put gas in it about 10 times, and it's stalled out or nearly stalled out after 4 or 5 of those times. The first time it happened I had to have the car towed back to the dealer. At the time, they thought it was bad gas, but the repetition of the problem has them stumped. There are no warning lights or error codes. I have had the car back to the dealer on four occasions, and unfortunately they can't replicate, find, or correct the problem. Now Subaru is involved. The car also runs rough and shifts rough, compared to the identical 2012 Outback I was given as a loaner the last time I had it in.
View 6 RepliesSubaru - Outback :: 1991 - Where Is Gas Cap Release
Where the heck is the gas cap release. Just bought it to get back home as the jeep needs broken motor mount fixed and had to leave it in town. The subaru is pretty beat up so the gas cap release could be hiding (as in handle gone) ?
View 5 Replies