Nissan - Frontier :: 1998 - Whirring Or Humming Noise While Clutch Depressed
In my 1998 Nissan Frontier I had the clutch replaced at about 115,000 miles. That included a "clutch kit" which included a new throwout bearing. Currently, I'm at only 145,000 miles. Much of that is highway miles.
However, a noise has developed. It's a whirring or humming that happens when the clutch is depressed (disengaged). The noise is not present when the clutch is released in any gear, including neutral.
My first guess would be the throwout bearing, but again, that was replaced only 30,000 miles ago, and plenty of highway miles. The original lasted as long as the original clutch.
My second guess would be the pilot shaft bearing. That was not replaced with the clutch. (So the shop says.)
Any other guesses or advice? No matter the case, is it a problem if I leave it be? I can live with the noise if I know it's not really a problem.
Nissan - Vibration - Frontier :: 2005 - Roar And Vibration That Keeps Getting Worse Over Time
I've got a 2005 Nissan Frontier that has a roar and vibration that keeps getting worse over time. It happens as long as the car is rolling, but is the loudest at around 35 and 65 mph. From the driver seat is does sound like it's coming from the front passenger side. A few months ago I was driving across a curvy road and when I got home I could smell hot brakes. I checked, and the front passenger side caliper was stuck. I rebuilt the caliper, and that seemed to free up the wheel, but didn't fix the roar. I drove a couple more weeks and found the caliper stuck again. So this time I replaced it. The wheel has been fine since, but the roar is still present. After a while I figured it was a bad wheel bearing and replaced that too. But, that didn't work. I've also taken it to a shop and had them check the alignment, to which they said it was fine. I'm still racking my brain trying to figure this out.
View 5 RepliesNissan - Frontier :: 2004 - Brake Shudder Or Vibration
I have a 2004 Nissan Frontier with V6 non-supercharged engine, 4x4, with manual transmission, 150k miles. For approximately the last 30k miles, I have had a persistent shuddering in the cab when I apply the brakes slowing from about 15 to 0 MPH. It is accompanied by a low humming noise that decreases in pitch as the truck slows down. It only happens when the brakes are warm; about 70+ degrees outside or after I've been slowing down a lot. It does not seem to correspond to engine temperature, only my perceived temperature of the brakes. There is no pedal feedback, and it does not shudder when I stop using only the parking brake. It does not seem to affect stopping distance.
I first tried to fix it by doing a very thorough front/rear brake job - new pads/shoes, new rotors/drums, and repacked front wheel bearings. That had no effect on the problem. I tried rotating the tires and that had no effect. I then did a complete front end job and replaced all the bushings and balljoints via brand new pre-assembled control arm assemblies. I also replaced the tie rod assemblies, sway bar bushings/end links, and had an alignment done. That had no effect.
Based on the repairs I've done, I would assume that it is having to do with the front brakes, but is not warped rotors or anything in the front suspension.
Nissan - Frontier :: 2003 - Runs Hot When Idling
Our mechanic is stumped. The Frontier runs hot when idling. The clutch fan and thermostat have been replaced. The radiator has been flushed. When you are driving or you turn off the A/C, the temp goes down. The next suggestion is to replace the radiator, but I'm already hundreds into this so I hate to do anything else unless I'm pretty sure it is going to fix it.
We do know that the catalytic converter needs replacing. Could this have anything to do with it?
Nissan - Frontier :: 2003 - Struggling On The Highway - Turn Off Overdrive?
A little background on my truck: Its a 2003 Nissan Frontier SE Crew Cab with a 3.3L V6 2wd, RWD AUTO. 78,000 miles. (yeah, I live in CO, so having this truck here doesn't really make sense when described through text, but with tire chains, and 200lbs in the bed it does better than most 4x4's if you know how to drive rwd! )
Anyways, I drove up to Aspen, CO and back from Colorado Springs (~575 miles roundtrip) for my rugby game and man did my truck have a hard time getting up the mountain passes. The speed limit in some places was 75 mph but I struggled to make it to 65 with the pedal floored-i think the grades were about 7% so not that much really for CO. I also noticed that my truck had trouble shifting into the right gear in my opinion.
I would be in 5th, and it felt like it would shift down to third and rev really high rather than shifting into 4th? My shifter knob has a button to turn off Overdrive, but i just didnt remember to turn it off and try driving like that, but would turning off OD make it up these mountain passes? If i can find some way to drive my truck up to Aspen without all the hastle (and embarassment) of not being able to go the speed limit, I would be so happy-that way I wouldn't have to drive our passat up there.
Stalling - Nissan - Frontier - Xterra :: 2003 - Engine Hesitating And Stalls Randomly
2003 NISSAN Xterra
Problem started a couple of days ago. While driving the car normally it suddenly stopped. I was able to restart it but it turned off again 60 seconds later. This has gone on with the engine running from 10 minutes to 10 seconds. The battery terminals and all cables are clean. Distributor cap and rotors have been cleaned. Fuel pump replaced last night. I still get the problem. Error codes listed were: P0328 - Pre Detonation (knock sensor) Bank 1 causes could be restricted fuel - over temp engine. Now this error has been coming up for five years and I've replaced the sensor numerous times. P0732 - Gear 2 Incorrect RatioP0102 - Mass Air Flow Low InputP1148 - Closed Loop Control Function, BANK 1P0420 - Catalytic Convertor, BANK 1P0134 - O2 Sensor No Activity, BANK 1
Regarding Fuel Starvation - NOPE, Engine Too Hot (it wasn't), Second Gear Not Within Ratio (never had gear problems), Knock Sensor and most error codes have been related to bank one. Error codes on car computer were erased and engine is still hesitating slightly and stopping. Just checked Mass Airflow Sensor and it looks clean.
Nissan - Frontier :: 2003 - Giving Shocks Every Time When Get Out And Reach To Shut The Door?
I drive a 2003 Nissan Frontier Crew Cab SE. I purchased the car in Honolulu and had no issues with it there. I moved to Colorado in June of 2010, and since then, I have noticed that my truck shocks me everytime I get out and reach to shut the door. I know that the climate is much drier here, but this isn't just a little zap...it makes my whole hand and up my arm feel fuzzy for a couple minutes. I have something installed on my truck that is like an electric anti corrosion device that is connected to the battery that i think is the culprit. It is connected to the battery and emits a high pitched, very faint tone that you can hear when the truck is off and you stand next to it. Do all Nissan's have this? Or is this just because the truck came from hawai'i? And is this normal?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Humming And Vibration When Throttle Depressed
I have a 1999 f-250 super duty 7.3 .... Recently my truck has started making a humming noise when push the throttle and I can feel a slight vibration, the noise and vibration go away when I let off the throttle, I have changed all five u joints, both wheel bearings in the front, the steady bearing, changed tranny and both diff oils, put new brakes and calipers all around and pulled apart the hubs but I can't seem to find what's causing it. What it could be or what I could check? It has an 8 inch lift and is sitting on 37's and some performance upgrades, could any of that cause this ?
View 9 RepliesNissan - Pathfinder :: 2003 - Accelerator Suddenly Becomes Unresponsive When Going Uphill
Took it to the dealer today to have the seatbelt replaced, which they did. As I was leaving the lot I noticed the airbag light was still blinking so I went back. Tech brought out the OBDII and ran a scan. No errors. Went through all menus and cleared everything only to realize his OBDII had the wrong 'code card' in it. So he went and got the right card and came back, ran it again, still no errors. Went through all menus again and cleared everything including what he called an old error but not one related to the airbag. As he was walking away to go get his manager the light... just went off on it's own. (Think it was mad at the tech, NOW I know why.. then I didn't.)
On the way home, on the highway, in Texas, going uphill... the accelerator suddenly becomes unresponsive. The car starts slowing down, 65, 60, in a 70 where everyone passing me is doing 80... So, I goosed the gas, revved it over 4k and ... the gear shifted and the car sped up... WTF?! Now this car ONLY has 83k miles on it. It was mint. No problems AT all, ran smooth as butter until I let the dealer touch it. NOW, it drives like gramma's jalopy and I can't for the life of me figure out what the heck the seatbelt has to do with the other issue but THAT drastic of a change is NOT coincidence.
Subaru - Forester :: Thumping Noise When Accelerator Depressed At A Speed Over 35 Mph
I brought my car to a dealership for its 120,000mi check-up, and they told me that the front axle boots were torn. They replaced the right axle, and on the ride home, I noticed a burning smell. Short story is four return trips, and the right axle replaced three times (including the initial replacement), and the smell has finally gone away. The weird part is not that I went back to the same place four times instead of giving up, it's that they told me this last time that they moved the replacement #2 right axle to the left when they installed replacement #3.
Why would they do that? Why would the smell go away if the issue was with that axle? I looked it up, and the same part is used on the driver's side and passenger side, so it wasn't as though they installed a left axle on the right the first two times. Does this mean the "new" axles were just new-to-me and had been reconditioned? If reconditioned, would it matter if a previously left axle was mounted on the right?
Meanwhile, about six weeks after replacement #2, the car started making a thumping noise when the accelerator was depressed at a speed over 35mph (but not when coasting above 35mph or with the gas on below 30-35). I was wondering if it was misfiring or something, but lo and behold! That noise went away with the axle switching. Way back at replacement #1, they replaced the boot on the left but not the entire axle until #3.
Eagle :: 1984 AMC - Turns Over But Engine Stops Running Unless Accelerator Kept Depressed
I recently acquired a 1984 AMC Eagle and I'm having trouble getting it to start. It turns over but the engine stops running unless the accelerator is kept depressed. Also, the car stalled at a light the one time I did get it running, so I'm thinking that there are some issues with the idle or with the carburetor maybe. I live in Colorado and I gather that the idle on these vehicles needed to get adjusted for the altitude, but I assume this has been done already as it has always been a Colorado car and has 125K miles on it. The gas is low, so possibly it might be something as simple as a gas supply issue, but judging by what other owners have posted online, it seems that this stalling problem is common with the Eagle so I think it probably is something more involved.
View 3 RepliesPrius (2004-09) :: Depressed Accelerator Pedal - Clicking Sounds From Engine
Sometime the car is fighting to move forwards when I start to depress accelerator pedal and it sounds like "click click CLICK..." the sound changes from lower to louder depending on how I depress accelerator pedal... (like the car is trying to hard to move)...
View 3 RepliesYukon :: 2003 GMC - Low Vibration Buzz / No Noise Even When Accelerator Is Applied
I have a 2003 GMC Yukon, 5.3 engine with 4x4, and with flex fuel option. The vehicle is making a vibration type sound. The sound is almost like a buzzing type sound. It's not overly loud and it's a low vibration buzz. This sound is not continuous, but occurs when the accelerator is applied. It will last for several seconds and then go away. This happens between the speed of 0-40 mph, but only when the accelerator is pressed. The vehicle will not make any vibration sounds when coasting. At speeds of 45+mph, there is no noise even when the accelerator is applied. I tried to pin point the sound, but it is very hard to locate. My best guess would be at the rear of vehicle. Maybe even where the fuel tank is located. This wouldn't be the fuel pump? I don't have any problems starting the vehicle or loss of power though.
View 3 RepliesNissan - Frontier :: 1999 - Air Conditioner Kept Going Off
I have a '99 Nissan Frontier 4cyl. p'up and the air conditioner kept going off. The truck has three drivebelts, all inline. The first is Crankshaft to the Power steering pump , the second goes from Crankshaft to the water-pump & the alternator and the third one goes to the air-conditioning compressor; the one that keeps coming off my truck & shutting down the A.C. I replaced it three times and the last time it went off within a couple of miles. I know the crankshaft and the A.C. compressor pulley's are out of line and believe that's my problem. A mechanic friend of mine looked at it and said he thought it was something called a belt-leveler that keeps all the belts from slipping off.
View 2 RepliesNissan - Frontier :: 2000 V6 Just Randomly Die Going Down The Road
It's a 2000 Frontier V6 4x4 CC with 104k miles. It just randomly dies going down the road. Sometimes it restarts. Sometimes it doesn't. Sometimes I just get a small blip (loss of spark or fuel - unsure which) when going down the road then it's fine again. It seems seems like a loose connection somewhere to me but I have checked and repaired everything I can find.
A little history of problems...
Fall 2014 - Fuel Sending Unit; I had similar problems a little over a year ago and I replaced this at ~90k miles. The stock one was corroded and the fuel pump wasn't getting power. Got the part from Nissan directly. Truck ran great for a year then started having same issues in fall of 2015. I am thinking this couldn't have gone bad again in only a year, but who knows? No engine codes at the time.
December 2015 - Distributor #1; I replaced it with one from Auto Zone. Had the same problems that day. Returned that and replaced with one from Napa Distributor #2 (New - house brand - supposedly made by Altrom - which is supposedly comparable to OEM) This seemed to fix it for a little while. At the same time I did the timing belt, spark plugs, wires, valve cover gaskets, a bunch of suspension work, etc. so I had the harness off. Did I knock something loose? I feel like I have checked it up and down.... doesn't seem that way.
January 2016 Bad Wire?; Same issues. Wiggling the harness into the distributor seemed to have an effect on restarting so I pulled the harness apart from the dist to the main and found a small cut on the casing of one of the ground wires. The wire was not damaged, just casing. Fixed that with a double layer of shrink tube and it ran fine again for a couple weeks. In this same period my catalytic converters also went bad. My exhaust manifolds cracked, next thing I knew I had catalytic converter codes on both sides of the engine. Ran it like this for a few months.
April 2016 Distrbutor #3 Same problem. Randomly dies. Gets progressively worse over a couple day period. I gave up and took it to a shop (Downing St. Garage in Denver, CO) They diagnosed it as a bad distributor so I had it replaced AGAIN (they were nice enough to use the Napa part I bought and get a free warranty part)
June 2016 Distributor #4 Same problem again. Still have not replaced cats - did not want to spend the money when the ignition problem seems un-related. Replaced distributor with another warranty part from NAPA. This time the one that I took off made a crunching sound when you turned it by hand.
August 2016 Finally replaced cats. CEL codes were gone for an afternoon then the truck started sputtering down the road again... CEL P1320 and CEL P0325 BACK AGAIN!
I am at a loss on what to do. I have read that the MAF sensor can get dirty... but this doesn't seem to explain the P1320. Anyway, I ordered some cleaner, a new knock sensor and another distributor (this time Nissan brand but re-manufactured... they no longer sell new ones.)
Nissan - Frontier :: Engine Shuts Down Will Restart Only After A While
When I cut off the engine by mistake (shift slip ie ) the restart comes around but only after about 5 to 15 minutes . The last time this happened the car was at an intersection and this situation is getting dangeous.Why is the restart taking so long ?
View 2 RepliesNissan - Frontier :: 1999 - Overheating Over 45mph
I have read two other threads that indicate a leaky head gasket for Nissan Frontiers overheating...but I'd like an opinion on my problem: I have a 1999, v6 3.3L, 4x4, manual Frontier that I have owned since 2001, always well-maintained, timing belt, water pump and thermostat already replaced a couple of years ago; currently has 129k mi. I rarely drive it (about once or twice a month).
Last time I drove it (I'm in AZ and heat was over 100 degrees) it started right up and was fine until I'd gone about 3 miles on the freeway doing about 65mph. Started to climb in temperature, but not into the red zone. I drove with it hovering just above the midway point (midway meaning perfectly normal temperature on my gauge) for a couple of more miles, when it started to climb just a bit more, I got off the freeway and dropped under 45 mph, the temperature went down to normal. I drove about 40mph back home and haven't driven it since.
I checked my coolant, which was extremely clean and not low, and was not boiling when I checked it soon after the temp went up on the freeway. What is the most likely cause?On a side note, since I do not drive it that often, what is recommended as to the gas that has been sitting in my tank since? How long does the gas stay good for? Further wondering how often it is recommended I drive it, for how long and at what sustained speed to keep my truck up and running?
Nissan - Frontier :: 2000 - A/C Malfunction - Not Cooling In Hot?
I have a 2000 Nissan Frontier that is a 4X4 and has the V6 engine. Mileage is 172,000+. For a few years, I have had problems with the AC no longer cooling after I drive 20 or so miles and stop the truck, go in a store and start back up only to find that the AC will not cool after the stop. This seems to happen more when the weather is hot. Only once has it gone out without stopping the car and it was on I40 driving trough Oklahoma in 100+ degree weather. Once it quits cooling, after driving 20 to 30 minutes, it usually starts to cool again. It sometimes speeds up the process if I roll the windows down.Coolant levels are fine.
So...is there a faulty sensor somewhere? What could it be that is the problem?
Nissan - Frontier :: AC Compressor Clicking / No Cooling
We have a 2003 Nissan frontier pickup (automatic).The AC recently stopped cooling, but the fan works. It was cooling perfectly great when all of a sudden, it stopped. If we turn the AC on, the compressor (I'm guessing) starts to click and continues to click until turned off. (started to grind under hood). It's not a rattle, definitely a click as if it wants to turn on but can't make the electrical connection. It kind of sounds like when a starter has gone bad and it clicks. Except, it does it repetitively until turned off. This doesn't happen if we turn on the fan but leave the AC off. Does it sound like the compressor went out? How can we troubleshoot it?
View 19 Replies