Golf V R32 :: Slight Whistling Almost Like Squeaking At Idle - Vacuum Leak / PCV System?
4601 DBP, just under 35k on it. At idle, i hear a slight whistling almost like squeaking. I took it to my independent tech and he showed me that if he removed the dipstick for a second while idling, the noise stopped, due to lack of vaccuum, so he believes its in the pcv system. I am still under powertrain and obviously federal emissions 8yr 80,000. Go start your R and listen at idle inside the car for a whistle or squeaking noise that seems like its inside the passenger dash.
View 13 RepliesMazda - Mazda6 :: 2006 - Bad Noise And Jerk In 4th Gear
we have an 2006 Mazada 6 automatic transmission with the option of manually shifting gears. we have had it a year and the only maintenance is work on the air conditioner, oil changes, and new tires. when accelerating on an incline or sometimes during/after a curve as it shifts into 4th gear it makes a terrible noise and the whole car jerks. the best way I know to describe it is it feels as if the bottom of the car is about to fall out! when we first purchased it, it done this a couple times and basically quit doing it for a few months.
It seems to be getting worse though. we have never had a check engine light. we sent a can of "sea foam" through the gas tank and this seemed to work. a local mechanic examined it and test drove it but couldn’t find anything wrong with it. (of course it didn’t act like this when he drove it!) I called mazda dealership and they cant tell us anything without us bringing it in and charging us no telling how much just to look at it. no one seems to be able to figure this out….
Mazda - Transmissions - Mazda6 :: 2005 - Soft Scratching Noise When Accelerating
I have had this car for 4 years, and it's been driving, and handling very well overall. Lately, I started hearing a soft scratching noise when accelerating, and especially going from 1st to 2nd, and 2nd to 3rd gear. There was some hesitation before shifting to the higher gear as well. I took the car to a local mechanic, and after test driving, and listening to the engine with a tube??? he told me that he needed to change the torque converter and the pump, and quoted me for $1936. My wife immediately wanted to sell the car and buy a new one. Half of my friends said the same thing (well, at least my richer friends did), and the others said to fix it and drive it while I could do so.
So, I took the car to another transmission specialist, and they told me that the transmission was in great condition, fluids, shifting, etc. Something doesn't add up here. I know that the engine/transmission doesn't sound the same as when I bought the car, but how is it possible to have that kind of diametrically opposite diagnosis. Meanwhile, I took the Mazda to a local dealership, and they quoted me for $4500 trade-in value, while CARMAX said they would give me $2500. Needless to say, I am at a crossroad - we know we have to change the car soon, but how soon and under what circumstances, this is the question. Then, just today, another mechanic said that the engine is unbalanced, and is giving a low, and powerful vibration, and the harmonic balancer needed to be changed.
Mazda - Tribute :: 2008 - Brakes Started Squeaking While Driving
A year 1/2 ago my wife's car (2008 Mazda Tribute) started acting funny.
The brakes started squeaking while driving, but as soon as the brakes were applied, the noise stopped. They also had a mild grinding sound. Not a metal on metal (aka no brake pads)...very superficial. Had to slam on the brakes and it activated the ABS (light did not come on) which caused the brakes to go to the floor.
Brought it in to the mechanic we always bring it to. They changed the pads and resurfaced the rotors. I KNOW they bought the cheapest aftermarket pads. I'm sure that and because the pads weren't deglazed (I'm assuming they didn't) is what is causing the noise.
Well...brakes worked fine. Months later had to slam on the brakes again. Again, ABS activated (no light came on), brakes went to the floor. A day later it was still going to the floor.Brought it back to the mechanic. They said nothing was wrong with the brakes, but they resurfaced the rotors. Brakes back to normal.
Happened again. Noises still there. Rotors resurfaced. I asked if the cheap aftermarket pads could be the problem. Of course the shop said no. Brakes went back to normal. Well, it happened again. Had to get on the brakes. and now they are almost going to the floor.
Brought it to a shop and they bled the brakes (not sure if they pulled the ABS fuse or not). Brakes are still spongy and go down far, but not as bad. Doesn't appear to be the brake booster (put foot on brake while car is off and brakes depress when car is started). Brought it to another mechanic (thinking it was the master cylinder) and he says he doesn't think it's the master cylinder, but an ABS problem.
Lexus GS 2013+ :: Loud Whistling / Squeaking Noise From Driver Side Mirror - GS350
I recently upgraded from my '14 IS 250 to a '15 GS 350. So far I am loving the car except for one thing. When driving above 50mph, there is a very loud whistling/squeaking noise coming from the driver side mirror area that is driving me crazy when the window is open. If i close the mirrors, it goes away.
I plan to have the dealer look when i go for the 5k service.
Mazda - Mazda6 :: Misfiring On Cylinder 3 / CEL Flashing
My '04 v6 wagon 100K will misfire in really damp conditions. Last fall after going through a massive puddle and today after sitting for a couple of days of warm damp foggy & rainy New England spring weather. OBDII scanner is reporting cylinder 3 as the one misfiring in the fall, today there were a ton of codes (that I didn't note).
So I made it about 2 miles from the house and had to turn back. No power, check light flashing. I had to put it in manual and keep the revs highish (3-4K). When I got home the exhaust manifold was glowing yellow, assuming one or more cylinders were passing fuel out to the exhaust and it was being burnt off in the manifold.
My question: could I have damaged any gaskets back there? This could be my imagination but I think I'm hearing a new noise that I'd normally attribute to an exhaust leak downstream of the muffler, very subtle - like a gentle light but rapid thud. I only hear this noise with my ear to in the front driver's wheel well. There's no ticking noise I normally attribute to leaks near the manifold. My imagination or is it easy to damage something in the circumstances I describe?
Mazda - Mazda6 :: 2003 Will Turn Over But Not Start
My son's mazda 6 will turn over but not start. the things I have done:
1. replace crank sensor
2. replace cam shaft sensors
3. it has spark
4. fuel pump works
5. sprayed starting fluid in still will not start.
What else should I check? Security system?
Mazda - Mazda6 :: 2007 - Loud Sound That Comes From Under The Hood
I have a 2007 Mazda 6 with 133000 miles on it. Recently it has started making a very loud sound that comes from under the hood. The sounds is comparable to the sound a semi truck makes if it is idling. The noise is not constant, usually happens when I put the car in park or if I'm driving at low speed (under 20mph). The sound lasts around one minute.
View 2 RepliesMazda - Mazda6 :: 2006 - P0302 Random Misfire - CEL Comes On
Mazda6. I have a check engine light for a random misfire on cylinder 2. I have changed the spark plugs, the injector, and even the cylinder 2 coil, but still have that random misfire. The funny thing is that it would run great within short (about 30 miles) one way trips. Lately, I have gotten a new symptom: It has started to hesitate and can feel a loss of power but only once the car has been driven for about ten minutes non stop. Can't figure this out.
View 12 RepliesMazda - Mazda6 :: 2003 - Car Suddenly Stops While Driving
I have a 2003 Mazda 6, 5-speed manual transmission. I was driving on the highway today (going about 65mph), and all of a sudden, my car kind of "jolted" (like it stalled out). When I tried pushing the gas pedal, the car wouldn't accelerate. When this happened, the check engine light (and some other lights) went on, too. I pulled over to the side, turned the car off, and turned it back on. It seemed to start fine and gas/acceleration was working. Fortunately, I was able to get home, but it started doing it more frequently up until I got to my apartment. Each time, I had to turn the car off and restart it.
Oddly enough, when the car does this and I pull over to the side, the engine is still on. However, even though the engine is on and the car is idling, I noticed the RPMs were sort of jumping between 0 and 1000, and the engine was sputtering (like it was sputtering with the RPMs jumping, the only way I can describe this sputtering is like a heart beat). The only thing that seems to work is to turn the car off and turn it back on, which will then allow the gas pedal to work, only to have it happen again a few minutes later. The gas pedal doesn't get stuck or anything, it's just pushing it doesn't seem to accelerate the car.
I've already had the engine replaced on this car last year (at 80K) and the clutch a few months ago, too.
Mazda - Mazda6 :: Front End Vibration At Certain Speed And When Turning Right
2009 mazda6, I feel some vibration feels like wheel is out of balance coming from the front left wheel, it's most noticable at 30mph and again at 60mph. It's more noticable when i'm turning right, e.g. shiting to the right lane.
Already replaced four tires, balanced the tires and replaced front struts and rear shocks.. and it's still there!!
when shifting to the right lane, the vibration feels like da-da-da-da-da.. like I'm driving over some washboard road.
What could this be, is this CV-joint? can I ask dealer to check out CV-joint see if it's ok?
Mazda - Mazda6 :: 2003 - Chronic Ignition Coil Cause?
Can a problem elsewhere in the system cause ignition coils to go bad? I have an '03 Mazda 6s, 147k miles, owned it since new (Dec '02). 3 1/2 ~ 4 years ago, over a period of 6 months I had to replace 4 of the 6 coils. A month ago, one of the replaced coils went bad so I had all three rear bank coils replaced (cheaper to do all three at once rather than one at at a time since half the engine needs to be disassembled to get at them). This week, I started to get the initial symptom of a coil going bad on me: Occasional stuttering in the engine.
This issue always starts when it's wet outside. The first few times it started when going through a car wash, this last time was right after Super Storm Sandy dumped a lot of rain (I am not in one of the flooded areas, NH just got a lot of rain).
Mazda - Mazda6 :: 2003 - Some Hesitancy To Shift Into 1st When Cold
I have a 2003 Mazda6, 108K miles. Had the ATF changed last December at the dealer. Prior to this, there was some hesitancy to shift into 1st when cold. Last several months, it has gotten worse. Engine revs (as much as I allow it, which ain't much) and then goes into first. Dealer thought they had overfilled the ATF, and reflushed and refilled. Said they couldn't find any other problems. There is no CEL. Problem was better for a short while after fluid change, but now back to long hesitation. Car goes into Reverse fine when cold. Once the car is warm, I don't notice the hesitancy to shift to first. How to diagnose?
View 1 RepliesMazda - Mazda6 :: 2003 - Control Arm Bushings Cracked
MILEAGE: 65,000
Last time I was in, the shop replaced my sway bar links, which had already been diagnosed and the repair scheduled. Then, after replacing the sway bar links, the mechanic told me that the control arm bushings were cracked. They already put new struts on the front, as well. So I asked him what else was going to go wrong with my suspension. He said nothing else should need work. He also said that the car was safe to drive for a couple months but I definitely needed to get it fixed.
QUESTIONS:
Is it normal for a car with 65,000 miles to have cracked bushings? I realize that the car is 11 years old; I just wondered how much a car's mileage plays into cracking the bushings and, if so, after how many miles should one expect before cracking occurs.
Does it sound like they're trying to soak me? Why tell me one thing at a time? Perhaps more revenue from the labor side of things?
Assuming the bushings truly need to be replaced, does the community here think there is anything else that should be checked and taken care of at the same time? It is both costly and annoying to have to take the car back numerous times.
Mazda - Clutches - Mazda6 :: Clutch Disk Wore Out, Car Won't Move
I have a 2005 Mazda6 4 cyl manual transmission, purchased this past holidays. Last week the clutch disk totally wore out and the car was not moving at all... AT 68000 miles only. I am a new manual transmission driver and I think I might have been part of the problem. My mechanic, who is a family friend, has replaced already the clutch kit and he found out that the clutch disc was not only worn out but actually damaged, shattered on a side. So I got scolded by him and my father as they suggested that I damaged it by doing improper shifting. They suggested that I went from 4th or 3rd gear to 1st thus damaging the clutch disc for the car to totally stop moving.
However that's very unlikely in my opinion. I don't know if Mazda included some sort of safety feature in the transmission, but the car never let me go in 1st gear if it was already in motion, the shifter would lock if I attempted (found that out when driving in stop-and-go heavy traffic). I thought my problem was due to my foot frequently flirting with the clutch pedal in order to keep my driving and shifting smooth. In fact a few friends of mine who drove manuals in the past complimented me on my driving becoming so smooth in a short time. I also think that I bought the car with the clutch kit carrying some sort of damage on it, since in the first weeks of ownership, my practice period, I would often smell a burning odor when I was not doing things smoothly. Once I got better I never smelt the odor again until a few days before the clutch gave out.
Mazda - Mazda6 :: Transmission Shifts Really Hard After Driving For Some Time
I have a 2003 Mazda 6. Almost every day, after starting it and driving maybe .10 of a mile, it seems as my car shifts, it shifts really hard, like a thump. I am thinking of having the Transmission serviced. Is this worth it? About what should the cost be? What do they do, just drain the fluid and add new?
View 2 RepliesMazda - Mazda6 :: Feels Like Shifting When Going Uphill At Low Or High Speeds
I've got a mazda 6 v6 3.7 from the year 2010 with approx. 69000 miles on the clock. I noticed when going uphill at low or high speeds that the car seems to feel like it is shifting but it actually isn't. For example when I drive on the highway about 70 going up a hill it feels like it shifts every few seconds even on manual mode in 6th gear.
When I hit the gas it shifts back and I don't feel it anymore. At lower speeds it feels like it is doing a whole lot of shifting at low/medium acceleration. Again if I hit the gas and accelerate faster the car just goes normally up its gears. I think this is the torque converter doing this, but I am not sure whether it is normal?
Mazda - Mazda6 :: Clutch Started Sticking Right Where It Would Engage Into Gear
I have a 2006 Mazda 6 with 104k on it. The clutch started sticking a couple weeks ago right where it would engage into gear, and I'd have to use my foot to pop it back up. It only happened here and there until finally, it stuck to the floor and became very difficult, if not impossible, to get out of gear. So everywhere I looked, it seemed that the slave cylinder was the culprit. I got a new one at AutoZone, replaced it yesterday, and the car ran great last night and this morning.
Then, this afternoon, in one 10 mile trip, it went back to the original problem. Stuck with every gear change, then stuck to the floor after I pushed it in and darn near wouldn't come out of gear. What in the world could be the problem?
Mazda - Mazda6 :: 2007 - Clunk In Right Rear Suspension At Low Speeds
Have an 07 Mazda6 with 110k miles. It developed a clunk in the right rear suspension about 6 months ago. Constant clunk at low speeds, whether small bumps, snow-covered roads, etc. Been to five different mechanics with no luck.
So far, the rear shocks have been replaced; made no difference. Stabilizer bar and end links were removed from car and driven carefully around the parking lot; no difference. New control arm lateral links installed; no difference. Top shock mount plate is tight, and rear coil springs removed and inspected during that process; no difference. No brake pad retaining pins are missing.
When I sit in the back of the car with the seats down, the sound seems to come from the top of the shock mounting area, but perhaps the noise is just traveling up through that area of the car.
Could it be a bad lower control arm bushing? Each mechanic checks them with a bar and reports little play. But I don't know where to go next. Car drives fine, but the noise is maddening.