Impala - Chevrolet :: 2003 - Temp Gauge Will Go Up When Sitting Still In Traffic Or Going Uphill
When I'm sitting still in traffic or going up a hill the temp gauge will go up. But it goes up real slow. You can set and watch temp gauge and it will just jump up every minute or so. And it has 2 fans on it but they won't kick on till temp gauge gets up over the half way mark. But when temp goes up i can raise the hood and the motor does not feel hot at all. What could cause this?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F350 Missing Mostly Going Uphill And Running Sluggish
Lately I have been having problems loosing power. Truck wants to miss mostly going up hill and runs sluggish I'll pull off the road and let it idle for a minute and it will run fine. And it is only occasionally some days it don't happen at all and other days it happens quit often. New fuel filter, oil is good, had it on the scanner and isn't throwing any codes. Around 230k miles newer injectors.
View 10 RepliesImpala - Chevrolet :: 2007 - Speedometer Started Fluctuating Widely - Pedal Position Sensor Not Working?
My 2007 Chevy Impala has developed a brand new problem today. Driving down the block to the store, the speedometer started fluctuating wildly. I was going a consistent speed of about 10 mph in my parking lot and when I braked to a stop the speedometer started swinging all over the place, from 10 to 35 mph. It then gave me a message on the dash saying "Speed Limited to 107 MPH" and somehow killed my accelerator because the gas pedal no longer did anything. I restarted the car and the accelerator worked again for a bit and then pulled the same problem again. The speedometer is now fluctuating wildly the entire time I drive, including while stopped, but so far the message seems to have kicked on and disabled my accelerator only when slowing to a stop and accelerating out of a stop (it happened three times).
I know that the Impala's governor is set to 107 mph so I can guess why that message exists, but I wouldn't think a governor would actually kill the car even if it kicked in at the right speed.
It wasn't that long ago that we had to have our pedal position sensor resynchronized and the mechanic had mentioned that it was possible the sensor was going bad, but I don't think that would be the problem here as it seems like the car would actually have been accelerating sporadically, whereas in my case just the speedometer is swinging around despite an even speed.
Impala - Chevrolet :: 2000 - Hard To Start?
i'm having a hard time starting my 2000 chevy impala. it orginal had a security plug on it. i had it removed. to start when i turn on the turn signal there was a noise, the odometer when blank, the air bag symbol appeared. the next time i tried to start the car it would do the same thing but wouldn't even turn over. sometimes you can turn the key on and wait 30 seconds, step on the brake and it may start. i have continued to try for up to 3 minutes. if you put on jumper cables sometime it will start. what is the problem?
View 2 RepliesImpala - Chevrolet :: 2000 - Starting After Lots Of Cranking
i've got a 2000 chevy impala 3.4 v6 E. runs great once it starts, but lately that takes a lot of cranking. it's getting spark. it's got a new alternator, battery, starter, plugs and wires (and i checked for spark already) I think it's a fuel issue but don't know where to start looking because it has no other problems. there's no smoke or noises, no misfires, or hesitations. i put in a new fuel filter. i have heard that it could be the fuel pressure regulator or maybe even a leak in the line that's causing it to not get pressure. i can't hear any sort of fuel pump sound (maybe i'm deaf) is there a way to check this without a gauge? i simply don't have one and don't have the money to take it to a shop. p.s. i recently replaced both o2 sensors, but i can't see how that would effect the starting. pump, hose, regulator, fuse?
View 4 RepliesImpala - Chevrolet :: 2000 Stalling After Hitting Higher RPM
while at stop in netural, reve engine, it seems to want to stall after it hits higher rpm?
View 1 RepliesImpala - Chevrolet :: 2000 - Major Oil Leak When Car Is Running?
I have 2000 chevy impala with a 3800 series 2 engine with 170,000 miles on it. I have major oil leak which starts leaking when the car is running, i cannot see from the top and when i am underneath the car , I cannot see far enough up in the there to see where it is leaking, It is not coming from the seneding unit or the oil pan,,when the car is running it just pours out oil.
View 3 RepliesImpala - Chevrolet :: 2008 Hesitates At 2000 RPMs
My Impala hesitates at 2,000 RPMs At every speed level. My mechanic and the Chevy dealer can't figure this out.
View 1 RepliesImpala - Chevrolet :: 2000 - Intermittent Starting When Warmed Up
My son has a 2000 Impala which will not start if it has been warmed up and then turned off for 30-40 minutes. If you turn it off and wait 15 minutes it will start every time - wait much longer and you are stranded. The starter sounds normal and you would think it is going to start but it won't. The car sat at the dealership for 2 weeks and they couldn't solve the problem. If the car is cold it starts every time.
View 10 RepliesImpala - Chevrolet :: 2000 - How To Shut Off Change Oil Light
How do you shut off the CHANGE OIL LIGHT on a 2000 Chev Impala?
View 5 RepliesImpala - Chevrolet :: 2000 - Dies When Warm After Running For 10 Minutes
My 2000 impala starts when cold, runs for 10 min and dies, i found its losing spark when warm, i changed the coil packs, control module and cam sensor and have had no changes, it dies, and doesn't start, only turns over, i leave it for 30 min er so and it starts , runs for 10 and dies....
View 4 RepliesImpala - Chevrolet :: 2000 Chevy Whistle When Accelerate / Shift Hard
Why does my 2000 chevy impala whistle when i accelerate? it also seems to shift hard.
View 10 RepliesImpala - Chevrolet :: 2000 3.8L V6 - Code P0300 Multiple Random Misfire
I have a 2000 Impala with a 3800 V6 series 2 with 165,000 miles. The only code I had was a P0300 Multiple random misfire that occured off and on at first, Worse in the city Better on Highway. It would start running on half the cylinders and bogged down, with the check engine light flashing, after getting onto the highway it would straighten itself out at first. I thought i had water in the gas so i ran some heat through it. straightened out for a day then happened again so I thought maybe a should run some premium gas in it, The car ran like total crap until the premium was gone, so i thought maybe it's running too rich, I put 87octane in it and it ran great for a day or two, then it gradually got worse to where it would not straighten up on the highway, tried to die at stoplights and i had to drive it with 2 feet to get it home and park it. I've replaced the battery, spark plugs, wires, ICM checked good, coil packs are good, replaced fuel Pressure regulator, looked for arcing on the spark plug heat shields and it will not start. It turns over but doesn't try to ignite and when I get the slightest rumble of ignition, it backfires up through the manifold and I see a puff of gas or light smoke by the exhaust manifold.
The car had a vacuum leak around the intake manifold cover gasket and a leak on the fuel rail. I pulled the fuel rail off my impala, snugged up the rest of the intake bolts then disassembled the fuel rail, flushed it out and cleaned the injectors the best i could, then reassembled it. before i re-installed the fuel rail I hooked it up to the fuel lines outside of the engine and tried to start the vehicle. all injectors had a nice spray pattern. So i installed the rail and it still didn't start but it had more combustion than before although it's still backfiring like before. Checked the fuel pressure by turning the key on and the fuel pressure went to zero very fast. I blew the rail out with air so to make sure i didn't damage the regulator I replaced it with the old one, ran the test again with same results, so i reinstalled the new regulator. I performed the fuel pressure test a few more times while moving the fuel hoses and when i moved the back supply line the vacuum loss stopped then dropped to zero when i let off of it. So I replaced the fuel line connector and O-rings on the injectors. It no longer has a vacuum leak.
I cleaned the EGR Valve out and had no luck there, then I removed the Idle Air Control Valve-pushed the pintle in, re-ionstalled it and WooHoo! it started! Although it still ran like crap with the same random misfire I was still happy to hear it start.I pulled the plugs on it to do a compression test and all 6 cylinders have between 180-190psi so the engine is in good condition mechanically. I installed new plugs before getting the car restarted and when i removed them for the test they were covered in thick black soot after running for roughly 15 minutes max.
I have (2) 2000 Chevy Impala's so I've swapped sensors from my wifes car to see if it would fix it. I've tested the following MAP, MAF, IAC, coil packs and ECM. None of these made the car change. I believe it is a timing chain because the car has never had a new timing chain and is way overdue, but I haven't had a code for a crankshaft position sensor. Can the timing chain be bad without throwing a code? It's not out of time enough to change the valve timing because I had a good compression test but its not firing right and still has the multiple random misfire. I have not checked or received a trouble code for o2 sensors, crankshaft position sensor or cam sensor. Something has the timing retarded and is dumping extra fuel into the engine because my new plugs looked like they were in the engine for a year.
Impala - Chevrolet :: 2000 - Code P1811 / Hard And Long Shifting
I have a 00 impala w 4t65e tranny I believe I have a p1811 code of hard and long shifting. I also need both cv axles replaced. If i replace the axles and have then dropped. Is it possible with the pcs going out, i would be able to drive 600 miles both way to a family thing without getting stranded.
View 3 RepliesImpala - Chevrolet :: Sputter And Jerk When Start To Accelerate Past 25 Mph And Get Around 2000 Rpms
I have a 2002 Chevy Impala driving it in the city of Chicago. It's recently had the oil changed, and the transmission fluid flushed and filter replaced. This car was mine before I went off to school, and I meticulously maintained it for three years, and then my step sister inherited it. She drove it for two years, and then it sat in the driveway for a year and a half. It's got about 175,000 miles on it.
Problem: Every time I start to accelerate past 25mph and get around 2000rpms, the car starts to give out, sputter and jerk. It starts to drop off right when it should be shifting to second gear. When on the highway, even if I floor the gas peddle, it won't accelerate normally, but instead just crawls slowly to higher speeds.
It will eventually reach the higher speeds, but it takes about 5-10 minutes for it climb up from 25mph. I don't know enough about this level of car trouble to make a diagnosis myself, and would like an estimate of the cost for repairs. Also the car is getting around 19mpg on the highway, which I need to improve if I'm going to survive the $4.50/gal of Chicago gas. I'm hoping that fixing this problem will take care of that as well.
Impala - Chevrolet :: 2000 - Security Feature Activates At Start Up And Would Have To Wait For 10 Minutes?
I have a 2000 Chevy Impala and it seems that every now and then when I try to start the car the security feature activates and I have to wait 10 mins to try to start it again. On some occasions when the 10 mins are up and I try to start it the feature reactivates and I wait another 10 mins. This actually happened on a ferry ride and I held up the offloading of vehicles. My question is, Will a remote starter installation alleviate this issue? If not. What can I do?
View 5 RepliesImpala - Chevrolet :: 2000 - Developed A Side-to-side Shutter During Acceleration
I have a 2000 Impala with 215000 miles and it keeps on running. It has developed a side-to-side shutter and only happens during accelleration. It smooths out once I stop accellerating. I have had a left rear wheel bearing replaced hoping this would solve it. Not so much. It feels like it is coming from the rear of the car. There is no movement in the steering wheel. Could this be motor mounts?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Acceleration Is Also Getting A Bit Sluggish Especially Going Uphill
What is a "normal" number people see on their load factor? Mine was around 25-30 a few weeks ago but I noticed it is increasing to around 30-40 once I'm in gear, in park it's fine. My acceleration is also getting a bit sluggish too especially going up hills and my throttle isn't responding all the way, my turbo boost is normal though and I don't think there is any VGT stiction. I'm thinking either a fuel filter or a MAF sensor to start with. Fuel filters have been in exactly 10 months. Can a dirty fuel filter, air filter, or MAF sensor affect engine load at idle and how fast it accelerates? I feel like I'm pulling a trailer and with it being more sluggish, my transmission is shifting harder as well.
View 14 RepliesFord F-150 (2004-2008) :: Truck Shuddered / Lost Speed And Incredibly Sluggish Trying To Get Uphill
My truck decided to have some issues last weekend coming home from a friends house. After being on the road for about an hour the truck shuddered, lost speed and was incredibly sluggish trying to get up the hill. It flashed the CEL and then went out. I was doing about 75 with the cruise on.
After slowing down to about 60 it stopped the shuddering and resumed operations as normal. Until about 20 minutes later when it repeated the above.
The next day I grabbed my reader and found the P0302 and P0306 codes. I cleared the codes and took it for a "test" drive up and down the mountain to see if it would trip the codes again. It didn't flip the codes. I thought I might have been dealing with a "one off" issue and left it alone for a few days.
Two days ago the CEL light came on and stayed on this time. Sure enough P0306. Cylinder 2 did not throw a code this time. After doing some research on here I ordered two new COPs and bought a mechanics stethoscope and some new spark plugs just in case.
The stethoscope confirms that cylinder 6 is having some issues. The COPs came in today so I'll take it apart tomorrow and see what I see. I'll be looking at both the COPs and the plugs to see what may be causing the problem. The "nice" thing about this is that at least it's one of the easier COPs to get to.
Should be a nice day for working on the truck.