Accent LC (2000-05) :: 2001 Engine Cuts Out Intermittently - Idle Roughly
Been having a fair bit of trouble with my accent, at first my car sometimes would hesitate on acceleration in 1st gear. Now it has a rough idle and the engine just completely cuts out at random. It does however start straight back up. It makes an odd noise whilst idling almost like a misfire from the exhaust. On start up it blows a lot of white smoke. And when you do get driving it is really jerky. It's been serviced every 5000ks. I've changed spark plugs, map sensor and throttle body sensor, put a fuel injector cleaner through and still no improvements. It's been booked into the mechanics for next Tuesday.
View 1 RepliesAccent LC (2000-05) :: Stalling And Idle Roughly Once Warmed Up - Random Misfire
I'm having continued issues with my mom's POS 2005 Hyundai Accent. It usually runs great cold, but once it's warmed up, it will stall out while driving. This almost always happens when accelerating from a stop. After it stalls, you have to let it set for 30 seconds to a minutes before it will start again. It will also sometimes idle roughly.
I've changed out the TPS and the MAP sensor, the battery, the CPS, the fuel pump, and the spark plugs. I did find that the radiator bypass hose was leaking on to the wiring for the O2 sensor. I fixed that, and the wires appear to be fine. I've sprayed throttle cleaner around the intake and can't find a leak. I scanned the ODB codes and I'm getting a Random misfire, misfire on cylinders 1, 2, 3, and 4, the Throttle Position Sensor and the MAP sensor, both of which have been replaced.
Tonight during my troubleshooting I was trying the wiggle test on the various connectors and got zapped when I was wiggling the coil pack connectors. Is that normal? I'm starting to suspect a wiring or electrical issue, but I'm not sure how to troubleshoot that.
Hyundai - Accent :: 2003 - Clutch Squeaking When Depressed
Earlier this summer I bought a 2003 Hyundai Accent with 130k miles on it. Recently I have noticed a squeaking/squealing sound coming from underneath the hood. I first noticed it at traffic lights, but I have determined that it occurs whenever the clutch pedal is depressed, and continues until the clutch is released.
My first question is - is this serious? (Is it dangerous, or will it compound significantly if I do nothing?) The clutch still seems to work fine, and I can stop the noise at traffic lights etc... by putting the car into neutral and letting off the clutch.
My second question is, how did I cause this? Coasting with the clutch fully depressed, or too much downshifting?
Background: Recently, I bought a Scan Gauge to provide real-time fuel economy feedback, and began to experiment with different driving styles. I found that I could really boost my fuel economy by coasting down longer hills on the highway (when there were no other cars around). To do this I was pressing the clutch all the way to the floor, figuring it was the same as putting the car into neutral. When my speed began to decline after the hill I'd ease back into 5th. One hill in particular comes into town where there is a light. If the light turned red I would stop coasting and do some quick downshifting as well as breaking. I was pretty aggressive with the downshifting on a few occasions.
Did either the downshifting or the coasting likely contribute to my problem? If coasting was an issue, would coasting in neutral cause a similar problem?
Hyundai - Accent :: 2008 - Timing Belt Replacement On Low Mileage Car?
Vehicle is an 08 Hyundai Accent 1.6L three door (hatchback) with 20,197 miles. This car was born on Oct. 16, 2007 and purchased in April of 2008. I told the owner to call the dealer and find out about when they should replace the timing belt as I had looked it up at the Gates site and found that it is an interference motor and also these Hyundai have some kind of lengthy warranty. When the tech or whoever she spoke to at the dealership asked about the mileage, they told her that she does not need to worry about the belt for about another five years, were rude and sounded inconvenienced by her calling. This leaves her with a bad taste in her mouth and more importantly, mis-informed.
I get the "Maintenance Log" out of the glove box and upon trying to decipher the timing belt interval, it states that the first course of action is an "inspection" at 30,000 miles or 24 months. How is a timing belt inspected? From what I have seen, a belt can look perfect today and snap tomorrow. But anyway, the next entry for severe service is replacement at 37,500 miles or 30 months which means this belt should have been replaced in October of 2010. Next entry is normal change at 60,000 miles or 48 months which puts us at April of 2012. After this it goes to 75,000 miles or 60 months.
I have already picked up the kit for changing the belt, tensioner, idler, and the two seals. How critical is it to change the spring as that was not included in the kit I got? I'm planning to do this job here in the next couple days as from what I can figure from the above log, It's way over due. I was reading some Hyundai forums and one stated that the 2011 model with the exact same engine calls for the first replacement due at 90,000 miles. How's this possible? Seems like these people (engineers) don't have all their stuff in one bag...
Volkswagen - Beetle :: 2002 - Idle Roughly On Occasion And Slight Rattling Noise But Only When Stopped
I have a 2002 VW Beetle 1.8L Turbo with over 120k miles. Recently it started idly roughly on occasion and had a slight rattling noise but only when stopped. When it was driving, it felt fine. This went on for about a week and then one day about a week ago it started for about 10 seconds and then stalled. Since then it will turn over, but not start. We've checked the starter, fuel pump, fuel pump relay and ignition coils and have replaced the crankshaft sensor (which was what I found on VW sites as saying it often solved problems like mine). The battery is new. Part of what I saw when researching was in addition to what is currently happening other owners had a long term issue with the car bogging down once in awhile at high speeds (50 mph+) for a few seconds and then picking back up again. My car did this as well and that's why I thought the crankshaft sensor may be the issue.
View 3 RepliesHyundai - Elantra :: 2002 - Low Beam Headlight Burned Out - Bulb Replacement
The headlight on the driver's side has burned out, should i move the battery in order to get to the bulb?
View 3 RepliesHyundai - Accent :: 2002 - Oil Light Flickering
'02 Hyundai Accent, 165K miles... My route to work is six miles of secondary roads and city streets (25-40 mph), followed by 16 miles of interstate highway (65-70 mph), then another nine miles of secondary roads and city streets.
I have noticed only recently (last couple of weeks) that when I get to the end of the interstate leg in either direction, as I wait for the light at the end of the ramp, my oil light will flicker (sometimes very faintly) if I leave my foot on the clutch. If I get into neutral and release the clutch, the light stays off. It will do that at two more stops in rapid succession, but by the time I am at the last traffic light or stop sign of the trip, it has stopped flickering regardless whether the clutch is in or out.
Oil is recently changed and at proper level.
Hyundai - Accent :: 2000 - Exhaust Smoke When Accelerate At Idle
2000 Hyundai Accent with 180K. Runs and idles smoothly. When sitting for a few minutes at idle I get a waft of smoke when I accelerate. The car burns minimal ammount of oil and the smoke is not apparent while driving.
View 4 RepliesHyundai - Accent :: 2002 - Engine Shakes While Slowing Down
I have a Hyundai Accent 2002 which has 126k miles on it. Overall the car runs well without any trouble. Recently I am noticing that if I suddenly slow down (like taking an exit from interstate or sudden traffic so that speed reduces to 30 mph from 60 mph or so), the front of the car starts shaking. On a very few occasion I have noticed that the check engine light comes up for a few seconds and disappears. At the same time car looses it's acceleration power. However, as soon as I slow down further (close to stop) everything starts working fine without any issue. What could be going wrong? The car is due for a timing belt replacement around 130k miles .
View 3 RepliesHyundai - Accent :: 2002 - Squeal Noise When Starting
I have a 2002 Hyundai Accent with 116K miles on it. Recently it started to make a squealing noise when I start the car. The sound stays there for about 15-30 seconds and then goes away. Also, while the car is running and I start the AC for the first time the same noise sounds for another 15-30 seconds. I took the car to a local Midas store and they told me to replace two things. Alternator Serpentine Belt and Power Steering Pump V-Belt .Does the parts sound reasonable? I am really novice about car mechanism.
View 7 RepliesAccent LC (2000-05) :: Hyundai Died At Idle On Park Now Cranks But Won't Start
Car died at idle on park. Tried to start it back up and was only getting crank. I took it to a local mech and he said my timing belt failed. I paid for the repair and the car still wouldn't start. The shop said the ecu went out. I replaced the cam position sensor and main relay under the dash. Still not getting it to start. I also have a ecu from an 05 accent, would this be plug and play? What else can I do?
View 3 RepliesAccent LC (2000-05) :: 2002 Hyundai Dies Then Starts After 10 Minutes
So I have a 2002 Hyundai Accent 1.5L. My car will drive 1-2 miles then it dies. After I let it sit for about 10 minutes it starts up again. I am getting to the end of what I know to do. I have replaced the ECU, Main relay, most of the sensors, Fuel pump, and fuel filter. When I bring it in to get the codes for it all I get is sensor faults even though I have replaced them. I am going to let it run for a little while and see if I can feel any heat from any relays under the dash. I like this car but not sure what else I can do.
View 4 RepliesNissan - Altima :: 2002 - New Clutch Replacement After 6 Weeks - Cause?
On 4/11/11 - we replace the clutch in our son's Nissan Altima. Yesterday - the clutch died as he was getting on the highway. It was towed to the same repair shop. They took a quick look and said it's likely the new clutch is gone. They weren't sure what our son did to it. We're baffled. What could he have done in 6 wks that would totally blow a brand new clutch? At this point - we don't know whether to throw good money after bad.
View 7 RepliesHyundai - Accent :: 2002 Auto Transmission - Downshifts With A Jerk / Thunk
2002 Hyundai Accent with automatic transmission. This problem happens only if I floor the gas gas on the highway (trying to pass somebody or get out of the way in a hurry) or if I apply too much gas after coasting around a sharp turn. My car will then downshift with a jerk and an audible THUNK!. Right now I just avoid those situations and it shifts through all its gears fine, it only happens when I cause a sudden downshift. Transmission fluid level and color fine.
View 1 RepliesHyundai - Elantra :: 2002 - Revving At Idle
I have a 2002 Hyundai Elantra that is exhibiting some strange behavior at idle.It wants to rev from 1500 to 3000 rpm, then back down, over and over again, every two seconds or so. This does not occur when the car is in drive or reverse; it purrs along at a consistent 1200 rpm.It all started with overheating and a water pump change, which was completed and reassembled.Then on startup, we began getting this revving. We double and triple checked the timing belt. We sprayed plenty of carb/choke cleaner in the areas of the vacuum hoses searching for a leak to no avail. Whenever we hookup the OBD code reader, there are no codes.Why does my car want to challenge everyone to a drag race, and what is causing this?
View 8 RepliesHyundai - Accent :: 2002 - Motor Runs But Rear Wiper Doesn't Move
During recent cold/ice spell, went to use my rear wiper and heard a pop (there was ice around the wiper base), then the wiper was flipping all over the place. Now I can hear the motor running but the wiper doesn't move. Plus, I can easily move it around by hand - no resistance. Do I have to replace the whole motor or is there possibly a gear or linkage between the motor and arm that stripped or popped away, so that can be fixed? 2002 Hyun Accent.
View 5 RepliesSanta FE SM (2001-06) :: 2002 Hyundai Does Not Idle At Start
When I start it up it won't idle untill you give it gas to 2500 rpms and slowly let off the pedal to 1000 rpms to keep it running and itll stay running. When you turn it off you have to redo it all over again. The plugs and wires were replaced. It started doing it couple days after the back 3 plugs and wires were replaced. Just got the fuel pressure regulator replaced and it still wont start up without giving it gas.
View 6 RepliesHyundai - Elantra :: 2002 - Rough Idle And Misfire When Hot / Intermittent Hesitation When Accelerating
2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
Ford Super Duty (1999-2016) :: 2002 F350 - Driveline Vibrates After Clutch Replacement?
I recently replaced my Ford Factory clutch with a new LUK kit, lever, pivot & hydraulics and I have to say it is absolutely perfect. If you are going to take the time to do the clutch, do it all. While we had it apart, I decided to push up my Up-Pipe replacement and do it while the transmission is out. What takes several hours to do is done in 30 mins this way. As we all know when we start in a job, we see other things and say well while it is apart I may as well do this, and do that. I decided to do the U-joints in the rear shaft. I had marked the shafts prior to removal for orientation but my assistant did not mark all 3 U-joint knuckles when he changed the joints and reinstalled the shaft.
I took the truck out for a drive and starting at about 15 MPH all the way to 60 ( I dared no faster) it was making me nauseous. Today I looked into it, marked current locations and started rotating front and rear joint 180 to no avail. I said lets just rotate the center joint and go from there. as I was pulling the carrier i noticed a HUGE but dull yellow arrow on the short shaft. I decided to look at the rear shaft and found a HUGE but dull yellow arrow 180 degs from the front. It looks like it could have been a factory mark. I repressed the center u-joint so the 2 arrows line up and the vibration went away. I can not express the aggravation this could have caused if not for those arrows. Take the time to properly index the drive shafts, it will save you tons of time and agitation.