Sonata NF (2006-10) :: Rough Idle / Lack Of Power Under 2000 RPMs
I have a 06 sonata 3.3L v6. I have been having misfire problems and lack of power under 2000 rpms and at idle when I am either a stop or just warming the car. What is happening I feel it shake and feel the misfire but after it gets up after 2000 rpm at highway speeds its completely fine. It struggles getting up to speed if i press on the accelerator. I have changed the spark plugs and all the ignition coils maybe about 2 months ago, I have also have changed the camshaft position sensor for the rear bank. I believe that it could be the crankshaft position sensor but I want to make sure....
Obd2 codes: p300,301, 303, p0012, p0011, p0014,
Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Lack Of Power
My issue I'm having - 2002 F350 7.3L has an 8 inch bds lift with 37/13.50 tires. I realize these tires are big but... while driving 100kms/hr or 60 miles per hour and I hit the gas the truck barely wants to move (without pulling a load). Thought maybe a turbo but I have no mechanical skills so here I am!
2nd issue, there's a bullydog chip in that truck when I bought it. he said he always ran it on extreme. I found it puffs way to much black when on extreme and on performance it seems a lot better so that's where I have it?.
3rd issue, the transmission gauge on the dash goes into red when climbing up hills ( I live in the rocky mountains so a lot!) but the bullydog chip says the tranny is only at its hottest 140C? I don't believe that's to hot but I do believe my truck is derating a little while the tranny gauge on the dash is in the red? is there any quick fixes out there for these issues.
Ford 6.0L Power Stroke Diesel :: Lack Of Power / Replaced Injector Now Won't Start
I was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Black Smoke - Lack Of Power
I have a 2003 with 150k miles. My 6.0 has black smoke and can barely crawl up a hill. Dealership is 30 days out for an appt. Air filter, oil change, alternator, and batteries are new. I removed the EGR valve and cleaned, but the valve seat is not perfect. I can see 20 to 30 mil gap around half of the seat. Is this ok or will that little gap cause this?
Hoses all look good. No alarm lights. I have no diagnostic tool but I can use a meter well. It did have an airbag light but I found the fuse missing and replaced it. The air filter alarm switch fell apart but I bypassed it till I get new part. No alarm lights now.
Ford 6.0L Power Stroke Diesel :: Lack Of Power When Going Up A Hill On The Interstate At 2800 RPMs
While I'm cursing at highway speed everything is fine. But when u punch it it pass someone it's like I actually slow down, same from a red light. I've got a livewire programmer in it and this problem is somewhat new. It just seems to keep getting worse, I was going up a hill on the interstate this morning and at 2800 rpms I was actually slowing down. I'm not sure if the fuel pump is going out or if the transmission is slipping or what.
View 7 RepliesFord 6.0L Power Stroke Diesel :: Blown Fuse Causing Lack Of Power To OBD Port?
Blown fuse causing a lack of power to the OBD port?
I just got my Kiwi2 BT OBD2 adapter and was hoping to start diagnosing my truck, but the adapter won't power on while connected to the truck.
I pulled and visually inspected fuse #12, I also verified power to the cigarette lighter plug and the accessory 12v power outlet.
The adapter powered up with no problem when I connected to a co-worker's Tacoma.
Ford 7.3L Power Stroke (1999-2003) :: Lack Of Power Going Uphill - Struggling And Lugging
Long story short, when going up hill or any incline for the matter it feels like it's struggling and lugging, blowing carbon everywhere. It's an automatic so I yeah can downshift sometimes but even turning overdrive off doesn't work in a lot situations. My EGTs are way too high and I'm not about to tow my project car to OKC unless I get this figured out. I live around Salt Lake City so towing can be hard up surrounding passes. Just cruising to park city at 70mph on I80 up a pretty good incline my EGTs were 1,000. Just driving around the city, some hills I see 700-800 when I'm going 35mph.
At stop lights I'm seeing 400 at idle. My probe on the pyro is going bad starting to flutter but even if I fix that I'm still having issues up hills. Boost is good, up-pipes don't appear to be leaking but fuel pressure is a little low @56 and I know it's not the fpr because I just messed with that yesterday, put a new poppet and oring in, I haven't checked the fuel pump yet or dropped the tank either. If it is in fact fuel pressure related, does it make sense for me to see smoke coming out, wouldn't that indicate too much fuel? I'm lost, it's driving unloaded like I'm pulling an anchor.
Regardless of which spring I put in the frx I get 56psi, even with the black one I may see 58psi but even with 58psi it was still lugging it's butt off up hills and making that terrible drone sound like F you down shift me now.
Ford 6.0L Power Stroke Diesel :: 2004 F350 - Lack Of Power While Accelerating / Stall And No Start
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 RepliesFord 6.0L Power Stroke Diesel :: E350 Dying When In Gear / Lack Of Power / Rough Idle
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F350 - Rough Idle / Lack Of Power
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Lack Of Power?
Picked up a second 7.3, just finished installing the new transmission last night, took it on a drive last night, everything was fine.
Went to bring it home last night- and found myself unable to maintain 50-55mph on back roads at 3500 rpm.
At first it almost seemed like I wasn't getting 3rd/4th gear, but upon taking it for a spin with torque pro, I am getting all gears, overdrive works, TC locks- all appears good there. Trans is getting really hot- but I believe I messed up the bypass lines or the bypass valve is not opening correctly- not the biggest concern.
I let the truck cool to more normal operating temps, took it for a spin, same story. I top out flooring it at about 55mph. No fault codes other than my faulty glow plug module. Everything I'm monitoring on torquepro looks fine with the exception of boost. When I floor my other 7.3, I get 15-20 psi, this, I get like.. 4. Unplugged MAP, nothing changed.
Turbo shot? Glogged pipes? These are my first initial thoughts. Let me know if I'm going in the right direction here, I can rebuild a gas motor in my sleep, but diesels are a newer animal to me, I've only had them about 2 months.
Ford 6.0L Power Stroke Diesel :: Rough On Cold Startup - Surge / Lack Of Power During Light Acceleration
My 2007 6.0 has a really rough (almost 'miss') during cold start up. After 5 seconds or so, it smooths back out and sounds normal. Until gauge reaches normal operating temp - there is a surge/lack of power during light acceleration. I also hear a frequent compressor coming on and running for a while which I am contributing to a possible vacuum leak. Maintenance is always done on time and I've already had a few costly repairs (both internally as well as externally) on the engine. I usually always wait for the glow-plug indicator to turn off before cranking the engine and let it idle for 5-10 minutes prior to driving it. Once the vehicle climbs to normal temp. everything seems to be fine but the compressor still comes back on every so often.IS it worth simply replacing the vacuum canister located behind the passenger side battery - or should I find someone to hook up a diagnostic unit first?
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Lack Of Power / Truck Will Barely Move And Takes Long Time To Accelerate Under A Load
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
Ford Aerostar :: 1993 - Lack Of Power / Sluggish
We have a 1993 Ford Aerostar 4wd Eddie Bauer edition. This van has 150,000 miles on it. In the past 2 years we've had a number of problems related to the van idling hard and having a lack of power.
First, the van revved high and low and was unable to maintain a steady idle....I replaced the throttle positioning sensor and this fixed the problem. Next, the van was running sluggish and was very slow to respond when you pushed the accelerator....I replaced the oxygen sensor and it fixed the problem.
Currently, (a few months after changing the oxygen sensor and the problem being temporarily fixed) the van is having the same issue as before I replaced the O2 sensor (running sluggish and slow to respond to the accelerator). If you press the accelerator down (even to the floor) it barely responds, you can get it driving at highways speeds but it takes a long time to baby it up to those speeds.
When you let off the accelerator after pressing the petal down it actually sometimes gets a second of power. It also is not maintaining a stable idle (fluctuating between high and nearly dying). I bought a new 02 sensor and installed it but it didn't fix the problem this time. The exhaust smells rich in gas. What else might make the van run like this? Possible solutions for where to look next?
Ford F-150 - 1997-2003 :: Lack Of Power / AC Stalling Out Truck
I have a 2003, 4.6 F-150 with 201,500 miles
I am having some A/C issues. It's just too hot out there.
#1 The truck has a lack of power when I have the A/C on. It feels like it wants to stall out in the lower RPM's. I loose power when I go 65mph+. The truck actually stalled on me yesterday in the parking lot. I turned off the A/C and it ran fine.
#2 I have to go over a 5000ft pass daily, I turn off the A/C when I go over it. Below the pass, the A/C doesn't work well and it's not as cold. But when I get over the pass, the A/C turns very cold. The pass is like a 3-4 mile stretch.
Ford F-150 - 1997-2003 :: Idles Rough And Seems To Lack Power
I am working on a 97 4.6 with 146k for a friend. It idles rough and seems to lack power (then again a 4.6 lacks power )
Has New:
plugs
wires
coil packs
fuel filter
sea foam intake
sea foam fuel
I have checked:
proper egr function
vacuum leaks
cleaned IAC
steady 17-18 in vac
clean air filter
cats do not seem to be getting too hot.
no codes
KOEO test ok
KOER test ok
The plugs worked some. Dirty MAF, clogged cats??
Ford 6.0L Power Stroke Diesel :: Lack Of Boost And Air Escaping Sound
Well, since I replaced the MAP hose a few weeks ago the old girl has been running fine. Until yesterday. I was leaving work and she had low boost, less than 10PSI, and as I passed by a parked tractor trailer I could hear the sound of high pressure air escaping because I had my window rolled down.
So today I checked it out. I found three possible leaks spots, BUT no "smoking gun". Take a look at the pics. The damage you are seeing is on the outside of the hot side boot at the turbo and the bottom of the cold side CAC tube. The cracks don't appear to penetrate to the inside. Could these still be possible leak sites? IDK.
I'm going to order replacements anyway. Ford wants WAY to much for these parts. I checked the MAP hose and it is just like new from several weeks ago. Also, I inspected the inter-cooler as best that I can without removing it. I don't see any issues with the tanks or the tank-to-core mounting. It all looks normal. If it does fail where does it normally fail at?
Ford Ranger / B-Series :: Intermittent Skipping / Bogging / Lack Of Power
My problem: Intermittent skipping / bogging / lack of power etc. It started about 2 months ago and is progressively getting worse. At first it was every couple of weeks, then once a week, now daily. It happens at variable times, temperatures (engine), and rpm's. When this happens I can pull over, shut the engine off, wait 1 minute and restart and it drives fine until next time. Now it will run fine for 1 to 2 minutes then stall. Sometimes runs rough first other times dies flat out. Starts right back up though?
What I've done so far: New plugs and wires. Tested both coil packs (primary resistance at input socket is .7 ohms on both coils and secondary resistance on top is 12.02 to 12.07 on both coils ).Since code 224 is primary circuit failure coil # 1 2 3 or 4 I replaced primary coil anyway. No luck. Removed ICM had it tested(at auto zone) 10 times in a row, it passed each time.
Checked the fuel system at the rail idles at 32 psi with vac.on at regulator and 40psi with vac. off at regulator. All within specs.
Checked compression. 170 psi lowest reading and 180 psi highest reading.All within specs.
Took some timing notes. Idles at 22*btdc after a minute or 2 it drops to 15*btdc for ~5 seconds then back to 22*btdc then dies flat out. Or it will go from 22*btdc to 28*btdc run rough for ~10 seconds then stall.
I disconnected the spout connector but it still idles at 22*btdc. I thought this would force the engine to run at base timing (10*btdc) but no go.
I'm thinking maybe the cam position sensor but I can't find it to replace it. It is not by the oil filter where it should be.
Found this info on rockledge site ("On other setups, such as the 2.3L Ranger, the PIP and CID signals are both generated from the crankshaft by virtue of a "dual vane actuator" which is essentially a doubled-up Hall-Effect sensor.")
Does this mean I don't have a cam position sensor? It's all rolled into one at the ckp? How to confirm that I have DIS or EDIS ignition ?
Ford F-150 (2004-2008) :: Engine Missing / Vibration - Lack Of Power Intermittently
I just did my plugs in my 04 F150 5.4 The truck had a really bad miss, and I figured it was time for plugs. I broke all eight plugs which I expected as the plugs were in there since new and had 120 000 miles on them. Replaced with champion double platinum and I am not certain that was the best idea.
The truck is much better with the new plugs but still has a miss and a rough vibration. The truck seems to shake side to side at idle but smooths out during normal driving conditions. I have noticed that it seems to lack power intermittently if that makes any sense. Also, the check engine light was on for a while but I tracked that down to a broken wire in the evap system.
So I am thinking first step is to verify that the coils and boots were installed correctly. I have to see if we have the scope module for the Genisys at work. I am going to check for vacuum leaks as well. I just changed the fuel filter and no change. Is there anything else I should look at? Would cam phasers cause a rough idle and intermittent loss of power?
I don't drive this truck every day so I can take it apart to diagnose it further...