Lexus GX 2004-09 :: Fault Codes P0037 And P0057 - Oxygen Sensor Heater Control Circuit Low
What can be done regarding these faults? P0037 and P0057
Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)
The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.
Mitsubishi Eclipse :: 1996 - When Turn The Car Off And On, It Will Shift Gears
I have a 1996 Mitsubishi Eclipse. When I start my car, it will only go through second gear. If I stop, turn the car off and back on, It will go through the gears and I can drive normally. I am now just putting the car in neutral while driving, turning it off and on again and it will shift like normal. Otherwise, it just stays in the lower gear. This has been steadily getting worse meaning, I would only have to stop and start the car once on a trip and now it is whenever I slow down to a lower gear. Every now and then it will jerk also. I thought it was a transmission issue but the transmission worked fine most of the time when this started and still does except when I slow down. The interesting thing is that it works fine when I turn the engine off and on again so I was thinking something else. The guy from advanced auto said it was possibly a power issue with something that makes the transmission shift and the transmission guy said it was electrical.
View 5 RepliesMitsubishi - Eclipse :: Stick Shift Won't Return To Center When Gets Hot With Temp Above 80 Degrees?
I have a 2001 Mitsubishi Eclipse, V6, 5spd, 91k miles. Only on hot days with temps >80 degrees, after about 30 minutes of driving (city or highway), the stick shift gets "sticky" and will no longer snap back to center. Also takes a bit more effort to switch from gear to gear This leads to a little delay (and frustration) while I fish around for 3rd while upshifting (or 4th while downshifting). Once the car has had a chance to cool off a bit (1 hr or so of not driving) the shifter behaves normally and will return to center during shifts... only to get goofy again after 30 min of driving. What's causing this? Only does this when ambient temp is hot. On cooler days, no issues. Clutch not slipping at all.
View 1 RepliesEclipse - Mitsubishi :: 2000 Sounds Like Airplane Engine
My son has a 2000 Eclipse which is making a horrible noise. Some say it is the lifters, some say it is a rod. Sounds like an airplane engine. The oil was not that low, maybe two quarts when we checked. He wants to sell it for 2000.00. Do you think it could be repaired and then sold? Do they have a problem common with this sound?
View 3 RepliesMitsubishi - Eclipse :: 2000 - Shakes When Put Into Reverse Or Drive
My 2000 Eclipse has a really bad shaking problem when put into reverse or drive. Also, it bogs down really bad when accelerating when first put into gear. It is the gs model. And I've searched everywhere online for an answer. It shifts fine. The idle drops down to around 500 when put into gear.. Whats the problem..
View 19 RepliesEclipse - Mitsubishi :: 2000 - Terminals For Battery Charging Rusted Out?
I acquired a 2000 Eclipse from a friend of mine. Within 24 hours of having the car, it died, and I got a jump. Went to get the battery tested, the charge was around 55% and the guy told me that he could not test the alternator because the battery tested bad, but he got out a multimeter and told me that it was only outputting around 12v, and said that was all he could do.
The battery was brand new (replaced just before I got the car), and the alternator was replaced in January or February according to the previous owner.
I've been able to take the battery out and throw it on a charger, but for what it's worth the terminals on the car are in very poor shape. Rusted out and seem very "finicky", even if they are installed nice and tight, sometimes it still won't supply power to the car and I have to adjust them. Obviously this might indicate that replacing the terminals would solve my issues, however, the alternator output should test fine then, yes?
Mitsubishi - Eclipse :: 2000 - Rear Left Wheel Free / Grinding Noise When Turning Right
I have a 2000 Mitsubishi Eclipse GT V6 FWD. about 138, xxx miles
My left rear tire/wheel has free - play (clicking movement) when grabbed at ONLY the 3 o'clock position and push/pulled back and forth (no free-play at 12-6 direction) in the air.
I had grinding noise from rear left side wheel when turning right couple weeks ago. After replacing wheel hub bearing assembly, the noise is gone. But still remains the movement ONLY at 3 o'clock. I replaced stabilizer bar links in both rear sides. This link doesn't look like the reason of free-play (clicking movement).
Also, I tested (push or pull) after switching the other side(right) wheel, it still had clicking movement at 3 pm. Therefore, it is not a wheel problem itself, I guess.
And I took off the wheel and fasten the lug nuts onto the rotor itself (so, without wheel in this case), then push/pull the rotor at 3 pm, but this time no movement in any directions. @@;; weird.. ONLY, I can feel the clicking movement at 3pm on the Wheel (or tire) even after rotating wheel, exactly in same spot (3 pm) movement~!!!! What's this case??
All 4 wheels aligned recently after got new tires.
I scrutinized inside wheel while pushing/pulling back and forth. But I cannot figure out which one is problem.
1. Knuckle.
2. Lower control arm ( or Rear rear control arm, not typo) which has a Ball joint and a cam bolt the other side.
3. Rear front control arm
4. trailing arm.
5. stabilizer bar link. (new)
6. Wheel hub bearing assembly (new, double-checked the nuts and torques)
7. Rotor and pads (new, if I push the rotor itself then no wobble or clicking at all directions as desribed above)
Where should I direct my attention and/or what component(s) should I look at given the indications above?
When I pull/push the wheel at 3 o'clock, it feels like wiggling the whole part of lower knuckle where is the connection part between the part of 4 bolt (backside) of hub assembly and lower side of knuckle.
I heard that 12 and 6 is usually an indication of ball joint, and play 9 and 3 is usually in indication of steering components ( tie rods , steering shaft or rack itself ), and all around play is an indication of wheel bearing (usually accompanied with a growling noise ).
Camry :: CEL On With P0606 - PCM Processor Fault / P0157 - O2 Sensor Circuit Low Voltage
2 weeks ago a check engine light came on with P0351-Ignition Coil "A" Primary/Secondary Circuit Malfunction, took the car to Toyota dealer and replaced ignition coil for cylinder No1. I drove the car for about 10K and check engine light came on again with P0606-PCM Processor Fault.
For the past week I was monitoring the DTC's using INNOVA- CanOBD2 Code Reader 3030 (ordered ODB2 USB tool to check live data on a laptop, on it's way...). I had P0606 on all the time, about everyday. For 3 times I had P0157-O2 Sensor Circuit Low Voltage (Bank #2 Sensor #2) on.
What's the link between the two DTC's? Why not P0157 alone? Or P0606 alone? What is the procedure to diagnose this?
Passat (B5) :: 2002 - CEL Code For Bank 1 Sensor 2 Heater Circuit Fault
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 RepliesFord F-150 (2004-2008) :: Transmission Malfunction Message Came Up On Dash / Sensor Circuit Fault
I was plowing and when I put it in reverse it felt like it slipped, but then the dash message trans malfunction came up. I checked the codes and I got P0722 output shaft speed sensor.
Code P0720 (oss) sensor circuit fault
Then the truck went into safe mods. Is it just the sensor or is my reverse going out...
Golf IV / Jetta IV :: 5 Engine Fault Codes - Cam Position Sensor / Knock Sensor / Secondary Injection Pump And Mass Air Flow
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 RepliesMitsubishi - Mirage :: 1998 - CEL Codes For Fuel Trim Bank / Oxygen Sensor Bank 1 Sensor 2 And Cylinder 1 Misfire
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
Ford Super Duty (1999-2016) :: 2000 F250 - Code P1746 - EPC Solenoid / Open Circuit
I have a 4r100 in my 2000 f250 7.3. I am getting a P1746-EPC Solenoid, open circuit. Does this mean this particular solenoid in the solenoid body has failed and should i replace the solenoid body?
View 3 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Code P0721 - OSS Sensor Circuit Performance Fault
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
Celica :: 2001 Toyota GT - Speed Sensor A P0500 / P0770 Shift Solenoid E
I have a 2001 Toyota Celica GT, automatic with 177,000 miles, it has been very well maintained. I started having a problem usually just after starting when it is still not completely warmed up. I try and shift it into reverse or drive, and the shifter says it is in those gears, but the car acts like it is in neutral. Once it gets a little warmer I can try it again and it will slowly shift into reverse or drive, usually though the rpm's seem to go a little higher than normal while it shifts. It seems to drive pretty well after this, shifting-wise, but not exactly perfect.
When it is completely warm though it usually drives really well - mostly I do a lot of highway driving. The transmission fluid is full, and looks perfect, nothing in it, not burnt. Previous owner had it changed a few years ago I believe. The check engine light is on and the codes are Speed Sensor A P0500, P0770 Shift solenoid E. My speedometer also works perfectly by the way. I don't have a lot of good shops around and I feel like the ones that are closest to me will see dollar signs in their eyes when they see that transmission code and will just try and replace the whole transmission right off the bat.
Camry :: Error Codes - Evaporative Emissions Control System Vent Control Circuit Fault
My check engine light has came on and I received these error codes
PO441 : Evaporative emissions control system incorrect purge flow.
PO 455 : Evaporative emissions control system pressure leak-large leak.
PO 446 : Evaporative emissions control system vent control circuit fault.
Also only my driver side fan is working, may be separate issue?
Ford - Explorer :: Check Engine Light Is On For Codes P0161 And P0155 - O2 Heater Circuit Sensor Is Bad
I have a 1996 Ford Explorer Eddie Bauer Edition 5.0, the check engine light is on and my code reader gives P0161 and P0155 both stating that the O2 heater circuit sensor is bad. I replaced all 4 of the O2 sensors in the truck, cleared the codes but they still keep coming back. I have tried for a few days now to find something online similar to this but have had no luck. I am not sure what else to do.
View 1 RepliesGolf IV / Jetta IV :: O2 Fault Codes Came Back After Sensor Replaced
Keep getting o2 fault codes. Replaced sensors came back. tried another set of sensors came back. Checked wiring for breaks no luck. Replaced ecu still no luck. So going through wiring again and checking for continuity. Looking for a list of what pins to check for voltages, and what each should be from ecu to sensor connectors. Looking for what wire is signal and how to and what voltages to check for...
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Getting Codes Abut Transmission Range Sensor Circuit
I have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...