Ford Super Duty (1999-2016) :: 2006 5.4l Runs Rough For About 10 Seconds When Started
Have a 2006 F350 5.4l that is mainly used as a plow truck. I drive it at least once a week when not plowing just to make sure it runs ok, etc. Only put on about 2,500 miles per year. Keep it in good repair - not by me, but by the dealer or mechanics.
Problem - last two times I started it, it started ok but runs real rough for about ten seconds. Sounds like the engine is going to die. After about ten seconds, it "catches" and runs normal. Have no problems when driving it. If I restart it, it doesn't do this, so it seems to only happen when the engine is cold.
Battery was brand new back in Sept. All plugs were replaced maybe 3 years ago, as was the cat converter and muffler. Run non-ethanol fuel. What might be causing it before I bring it in.
Audi :: 1993 - White Smoke Out Of Tail Pipe When Starting And Runs Really Rough
I have a 1993 Audi 100s 2.8L V6It needs new spark plug wires for sure. However recently when I start it up it has been blowing white smoke out the tail pipe and runs really rough. However once I run her for a while smoke goes away even when heavily accelerating. Also when It runs rough I can smell raw gas. Whats going on to my car?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Fuel Pump Runs For 20 Seconds At Key On / Long Start Takes About 6 Seconds
This applies to a 2001 F-350 with 73,000 miles on the engine. Engine oil level is good, batteries charged, HPOP reservoir is full and passes Cody test with flying colors. Fuel pump runs for 20 seconds at key on. Start takes about 6 seconds. If I shut the key off and restart immediately it starts in under 2 seconds but if I wait about 30 seconds it's a 6 second start. Here is an AE that I ran on it, it has me stumped. FWIW it seems to start quicker when AE is hooked up. ?? An odd whir type of noise comes out from somewhere under the hood when I first turn the key on and when I clear the codes with AE.
View 14 RepliesAcceleration - Audi - A6 :: Started Accelerating By Itself While On Highway
Yesterday in MN when it was -17 while on the highway around 5 pm my 96 Audi A6 started accelerating by itself. I was able to get of the highway and to a parking lot where it idled in park at about 4000 rpm's before I turned it off and let it sit for several minutes. I started it twice the second time it did not rev up to 4000, it was just normal. My question is this a sign of something terrible or just the cold messing with my old car? Should I have something specifically checked out?
View 2 RepliesAudi A4 :: 1997 Stalling - When Started Up And Left To Idle All Of A Sudden RPMs Drop
I have a 1997 Audi A4 that has been acting a little bit strange lately. When it is started up and left to idle all of a sudden the RPMs drop from around 600-800 to 100-200 sometimes rebounding back up and sometimes the car just dies. This also is happening while I am driving and stopped at a stop light for a short time. It will idle fine then suddenly drop RPMs and if I don't give it any gas then the car usually dies. I have just had some work done on it to try and fix this problem thinking it was the air flow sensor (or something like that) but apparently that is not the case.
View 2 RepliesPrius (Gen 2) :: 2004 Will Start But Only Runs A Few Seconds
My 2004 Prius is due in the shop Tues for a hybrid battery replacement. Codes indicate only one cell bad BUT...It is obviously having some problem running. We were very low on gas yesterday but wife filled it before she came home.
She parked it in garage. The Hy Batt indicated all green bars. She may not have pressed the Park button before Power - I do that a lot too.
This AM I changed the spark plugs before I tried to start it. I then started it (ICE & started-sounded OK) and backed it DOWN the driveway into the street and started down the street. The ICE stopped.
The batt indicated one blue bar so the batt would not propel it. After trying a couple times to make it run, I disconnected the 12v grd and let it sit for an hour. Then I reconnected the batt and the ICE again started showing hybrid at 4 blue bars and stopped after a few seconds. Tried it once or twice more, same thing.
Touareg :: 2004 Runs For 10 Seconds Then Dies
Not really sure where to go with this one. Was going to start with the fuel filter but I am not sure where it is at?
View 3 RepliesTouareg :: 2004 V6 Runs For About 10 Seconds And Dies?
My 04 Touareg V-6 will start, but will die about 10 seconds after or if I give it gas. I'm pretty sure it's one of the fuel pumps just not sure which one.
View 5 RepliesChevrolet - Cobalt :: Starts Normally / Runs For 2 - 3 Seconds And Then Stalls
2010 Cobalt, LS 2.2 Ecotec, with 13.7k miles. Oil level normal and battery voltage = 12.5V.
I've bought the car new in Feb. 2001. Car started and ran normally for the work commute on Friday, 9/2. Today the Cobalt starts normally, runs for 2-3 seconds, and then stalls. The accelerator has no effect. It's already been towed to the dealer..
Buick - Lucerne :: Car Bounced More Than Once - Air Compressor Runs For 5 Seconds?
I just put new rear air shocks on my Buick Lucerne. I noticed the back in my car bounced more than once when I tested them. After starting the car I hear the air compressor run for about five seconds. This seems to have no effect on my new shocks. The old shocks had holes in the bladder. What tests can I perform to figure out what's wrong?
View 8 RepliesFord - Focus :: 2001 - Runs Fine For 30 Seconds Then Stops
I start the car - a 2001 Ford Focus 4 cyl DOHC. It runs fine for 30 seconds then stops, as if it is no longer getting fuel. I can't start it again for a couple days then the same thing happens over again. FWIW, I parked the car for 8 months before this happened and only started it once in that time. But it ran fine then and before I parked it. What can this be?
View 1 RepliesPassat (B5) :: Engine Runs For About 3 Seconds Then Starts Rattling And Stalls Out
One of my friends recently asked me to change the timing belt on his 2004 Passat 1.8T. I put on everything as instructed by the manual that the parts department gave me. However, when I start the engine, it runs perfectly for about three seconds, then starts rattling, and stalls out. I took the belt off and put it back on three times and yet, it still continues. This rattling seems to be coming somewhere from within the exhaust system near the engine and sounds like a back-fire. The check engine light also appears when this begins happening. I replaced everything, water pump, pully, tensioner, and etc. Note, I am a professional mechanic and have worked on several Volkswagen cars, including my own, but I never encountered a problem like this one.
View 7 RepliesPrius (2010-12) :: Starts / Runs Rough For A Few Seconds Then Shuts Off
Car starts runs rough for a few seconds then shuts off (spark plugs and 2 coils were replaced a few months ago). Coolant reservoir level was way low so I filled to the full line, kept the cap off to cycle. During the time the car starts, the coolant from the reservoir violently "boils" over (out of the reservoir). Huge amount of white smoke from the rear exhaust and a burning smell.
Used Techstream and got the following codes:
Engine and ECT: P0117, P0302, P3190, P3191
Hybrid Control: P0A0F
Intermittently get misfile codes but this time around they did not return.
Ford 6.0L Power Stroke Diesel :: Runs For A Few Seconds And Stalls
My truck started fine my truck was running good. One morning while working from a hotel I went to start it in the morning and it started and stalled more than a few times but eventually ran fine later it did the same thing. The next morning it would not crank at all. I deduced it was the ficm and ordered a replacement the dash was acting funny and tach dropped before it died. I ran the. Test on the dash it swooped the gauges acted fine. I checked and wiggled sensors wires. I also checked were a splice at the crank sensor was it looked good then I bought a meter and the ficm seemed to have the correct volts it was a upgrade. Had 57volts at 1 screw koeo and while cranking.
PCM and replacing the crank and cam sensors. I don't really think it is the harness it will now crank and shut off crank and shut off like it did at first. He said it's stalling because it looses ficm sink. I haven't put new ficm on it ...the harness was allot better than the first. Could the crank sensor splice be wrong it is done its soldered together and heat shrink ... is it the ficm or the dash. I'm out of my comfort level I was also reading it only needs ficm sink to start. Not run. In addition #2 injector is throwing a code. I asked him if he thought the fuel was getting pressurized and his reply was the fuel has nothing to do with ficm sink. Also, I swapped relay out with my other 6.0. And its running fine This is everything I got ....
Ford Fuel System :: Engine Runs For 10 Seconds Then Dies
I have an 84 Bronco II with a fuel injected 302 in it. I was out wheeling with it the other day, and it was doing great until about 3:00. I got out to see that my brothers radiator had sprung a leak. When I got back in my Bronco and put it in gear, it just stalled. I started it back up and it ran for about 10 seconds then shut off. It kept doing that over and over again. Finally, I got tired of it and had someone get my truck and tow me out of there. Why would it run for about 10-15 seconds only and then shut off like it was getting no fuel (yes, it does have fuel in it)? I have a feeling it might be fuel pressure regulator valve because it was acting up a while ago..
View 10 RepliesFord F-150 (2004-2008) :: Starts And Runs For About 5 Seconds Then Stalls Out
I've got 200k on my Lariat. Engine was replaced 60k ago. It's in outstanding shape and is driven a lot. Suddenly this morning I start as usual and it runs about 5 seconds then stalls out. Every start, same thing. So it seems I am getting fuel pressure to start but it doesn't last.
I did replace the Fuel Pump Module within the past two years, due to corrosion of the FPM housing. At that time the truck would no start at all. Could it have gone bad already? I'm thinking this must be an electronics failure. It was perfect all day yesterday. 2004 Lariat 5.4...
Prius (2001-03) :: Engine Starts And Runs For A Few Seconds Then Bucks And Stalls
My 2001 Prius (230,000 miles) is unusable. I can clear the codes. The engine will start up fine. After a few seconds it starts bucking and jerking as if the engine is trying to engage something that won't turn and finally stalls. It is similar to a manual transmission car's action if you fail to push the clutch in when you stop the car. What the engine is trying to engage? I don't have any scanner to read the codes.
View 7 RepliesNissan - Nx :: Starts / Runs Fine For A Few Seconds Then Surging / Pulsing Idle?
Having some problems with my 92 Nissan NX2000. i just finished changing the clutch on the car now its acting horrible.
When i start the car, it will run decent for like 2 or 3 seconds then the idle drops down till it almost dies, catches itself, idle goes up to about 500 were it will pulse around for a few seconds until it dies. If i rev it it will stay running, kept it running for about 2 mins. but as soon as i let off it will pulse at 500 until it dies
After i changed the clutch it started up fine, it ran great for about 20 seconds before it just died. when i started it after is when the problem arose.
I took a video of the car running, which can be seen here. [URL] .... (It has never caught itself like that before and jumped up to 1000 rpms before. It normally will die at that point)
The video is really quiet, not sure what happened there. if need be i can get a video of the engine bay so its louder, was mainly focused on the RPMs.
Here's a few things i tried: Checked fuses, Changed spark plug wires, made sure they were all seated good, MAF wires were rubbed a bit so i cut the MAF pigtail off one of my other sentras and soldered it on,Changed to a good battery, Changed fuel filter, Added more gas (in cause gauge is broken), Made sure all connectors are plugged in, Checked around for vacuum leaks, found that one of the large hoses coming off the intake going to the engine had separated so i plugged them back in and nothing.
Ford 7.3L Power Stroke (1999-2003) :: Truck Starts And Runs For Forty Five Seconds Or So
Trucks been running perfect for 11,000 miles atleast. its last issue was a bad turbo but that was my fault. No issues whatsoever since. 10 miles down the road from work last night truck had a slight miss in between 55-60 for four or five seconds, I put the pedal down and brought it up to 75 or so just to see if it was my imagination and it felt fine so i wrote it off. It ran fine to the house we're working on i wanted to check on before I got home.
Parked it, it idled down to 650 before it came back up to 750 and it never does that and sounded different then it usually does. so i felt something was definitely up. i shut it off, was at the house about a half hour before i decided to head home, started and ran fine, three miles down the road the slight miss came back, it seemed to go away if i got on it pretty good and when i let off but just cruising with slight throttle it had the slight miss.
Got to my road where i had to slow down and turn and it idled down and died. I coasted over, unplugged the icp sensor and it cranked for 10 seconds or so and lazily came back to life. I got it home running decent and parked it. Scanned it with my old super chips tuner and it came up with a p0340 camshaft position code.
Matched my symptoms i felt so this morning i decided id go back to work and grab my spare out of my wrecked truck. truck started and idled perfect. made it to the end of my driveway before the miss came back and then it just died. took the car to work, grabbed my spare camshaft sensor and my maximus scanner, came home scanned it, no returning p0340 cam code but i swapped the camshaft sensor anyway and watched icp and ipr data, the ipr voltage is where it should be and rises while cranking while cranking.
ICP is climbing to almost 3,200 psi and it will begin to run when it peaks out. she'll fire for 45 seconds after 25 seconds of cranking or so and then it'll just die. if it sits for a few minutes it takes a few seconds of cranking before ICP will come off of 0. I've come to the conclusion that it is making high pressure oil it is just dumping it as fast as it can make it. I changed the ipr out because that can do it, it didn't change anything so I'm on to believing an injector is dumping it as fast as possible.
Is it possible for something to come undone inside the injector to make it dump high pressure oil or will a bad o ring cause this? i'm leaning towards a failing injector as when it does fire and run its definitely misfiring and i just put new o rings on them when i swapped them over from my wrecked truck but that was like 45,000 miles ago as well..