Toyota - Tacoma :: 2000 - Transmission Squeak When Let Off The Accelerator
My 2000 Toyota Tacoma 5 speed sometimes makes a squeaking noise when I let off the accelerator, most noticeably at speeds of between 25-35mph. If I press on the accelerator, the squeaking stops...it seems like it has to be related to the transmission. I was told it may be the U joint...
View 1 RepliesToyota - Tacoma :: Window Stuck - Master Control Switch Work Fine
An attachment point, on the front lower frame, broke, allowing the window to drop. I had the frame welded and put it all back together. The window went up and fine. The next time I tried to lower the windows, neither side would work. I checked the fuses. They were all good. I changed out the driver's side master control switch because some of the button contacts were corroded. This did not work. The window lock button is on the off position and the power door locks, which are on the master control switch, work fine. Could it be the relay?
View 1 RepliesToyota - Camry :: 1992 - Stalling When Come To A Stop And Taking Foot Off The Accelerator
I have a '92 toyota camry that we just purchased and put a new engine in... now it's stalling when you come to a stop and are taking your foot off the accelerator. we've tried a fuel injector, a fuel clean, fixed vacuum leaks, and replaced the fuel filter, and fuel preside regulator... it's still doing it and is getting worse.
View 1 RepliesToyota - Tacoma :: 2005 - Power Loss On Right Curves At Moderate Speed
I've got an '05 Tacoma 4WD with 145,000 miles. Very recently, when taking right curves at moderate speed ( e.g. freeway cloverleaf onramps), I'll lose power at the apex of the curve. It comes back immediately when the I straighten out. No warning lights on panel. It feels like no gas since there's no difference when I press the accelerator pedal.
View 17 RepliesToyota - Corolla :: 1997 - Rough Idle / Stalling Noises While Stuck In Stop And Go Traffic
I have a 1997 Corolla with 150k miles.
I had my catalytic converter and flex pipe replaced this summer. Lately, my car has been idling rough. While stuck in some horrific stop and go traffic three weeks ago, it started to make noises as if it would stall out. It didn't, but it still sometimes makes those noises.
The car seems fine on the highway. No loss of power. I did think that the hood felt too warm on a recent trip, but the temperature gauge in the car showed no issue.
The car hesitated when I tried to start it last week, but normally starts fine. It was the first cold day of the year.
I saw some white smoke come out of the tailpipe last week. It only happened once. Coolant and oil levels are fine. The spark plugs look good.
The fill pipe has been leaking gas for several months. It leaks if the tank is more than half full and it drips a bit of gas when I fill up. Two mechanics have not been able to find the leak and have told me not to replace it until it is a problem, given the age of my car.
I took it to a mechanic today (not the one who replaced the cat). He told me that the rough idling is due to the new flex pipe being shorter than what was originally there. He assured me that the car is fine to drive long distances and that there was nothing wrong with it. There's no check engine light or anything on the dash to indicate a problem.
I should be relieved, but I'm not. I've lost confidence in my car. Can the stalling noises and rough idling be explained away by a changed exhaust system? Or are these signs of a problem about to happen?
Toyota - Sienna :: 2005 - 3rd Row Seat Stuck In Up Position
The larger (60) side of my 2005 Sienna's third row seat is stuck in the "up" position. That is: the seat back will fold down, but the seat will not release from the floor in order to fold down into the well at the back of the vehicle.
The pull tab on the back of the seat that releases it moves in and out too easily. I viewed the mechanism under the seat and it appears that the pull tab is linked to a cable which rotates an armature, which in turn pulls one cable for each leg of the seat to release it. It looks like the cable connected to the pull tab is properly rotating the armature, but the legs aren't releasing. I can't tell for sure but it seems like the armature is rotated into the "release" position but it hasn't released the legs. I've crawled under the seat and tried my best to rotate the armature with my hands and a pair of pliers to no avail.
I was thinking my next step would be to try to rotate the armature with a little gentle persuasion (e.g. a hammer and a screwdriver or piece of wood).
Toyota - 4runner :: 2005 Jerks When Coming To A Stop
Recently purchased a 2005 4Runner Sport 4x4. I bought it before they had the chance to give it the once over but they agreed to do a safety inspection the next day. The car was in tip top shape so I was not concerned. As I was driving it home I noticed the car was jerking or rocking slightly as I was coming to a stop. I didn't think much of it but when they inspected the car the next day they found the driver side CV boot was leaking and needed to be replaced, which they did for free. When i dropped it off, I asked if they could look at the cause of the jerking and they said it was likely due to the CV boot and it would go away after the repair. Well it did not go away. I'm wondering what is causing this jerking and if it's worth a trip to the shop to have it fixed or worth going back to the dealer and making them fix it. Should I be concerned about safety?
View 6 RepliesTacoma :: Clunks Into Gear Every Time Come To A Stop
I have a new 2002 Toyota Dbl-Cab SR5 Pre-Runner. I love the truck except every time you come to a stop, the tranny clunks. Also, when you start to move forward again, the tranny clunks again. Ever tow something an when you stop you feel the trailer catching up with you in a clunk? Feels and SOUNDS just like that.
So me being the good customer that I am I called up for a service check. The service dept guy told me that this is normal on all Tacoma DBL cabs, Tundras, Sequias, etc. That is is the two drive shafts separating when I move forward, and pushing together when I come to a stop (esp. a hard stop). They checked it out and also re-aligned the truck since my steering was WAY off and the steering wheel was not even centered.
Now that I have been driving the truck for about 1700 miles, the clunk is getting much worse. This can't be normal! I love the truck but this problem is driving me crazy. Every stop and start I cringe at the expected CLUNK. It shakes the whole truck.
Chrysler - Ptcruiser :: Accelerator Stuck Down / Engine Light Comes On
I have a 2005 PT Cruiser convertible. 3 times now ghetto accelerator has stuck down. The engine light comes on and after stomping on the pedal and releasing it, the car does not want to accelerate and sitters as if it will cut out. After about a minute everything clears up and works normally. I have taken the car into 3 repair shops including the dealership and they cannot recreate the problem ...
View 6 RepliesAcura - Integra :: 2000 - Accelerator Pedal Getting Stuck?
2000 Integra with 95k miles in an excellent condition - used pedal jack when parked
I had to make a left turn and ramp up so put it on D3 - I pressed the accelerator and when I felt the speed could be higher (I am not comfortable to drive up the hills) so I must have pressed hard on the accelerator. It then responded
Not sure what was happening, I started breaking and steering - still around 30mph, guessing - it was not a wild drive.
Still not satisfied, I moved to gear 2 and stopped the car. Realized the car is still pulling, turned off the engine and realized the accelerator pedal is stuck.
I pulled it and it has been fine! With the engine off, I pushed the pedal hard and it always bounced back. Not sure that the getting in and out the pedal jack had been interferring with the accel pedal. It also looks like the engineers did a good job that with the stuck accel pedal, I did not end up in a wild drive - I had to brake and move the tranny to 2 but was able stop it - it was a mild up the hill, but unsure if it played a big role.
Santa FE SM (2001-06) :: Accelerator / Idle / Throttle Stuck Fully
I was driving along nicely, then faced with a climb up the hill, I floored it ... the throttle stuck fully and the revs up to 5000 RPM and the governor kicked in, zoom ... hmmm zoom hmmm .. I was lucky cuz I shut off the engine and was able to coast back down to my driveway. No code reader, I decided "how hard can that be" since it happened once before and then worked ok for 6 months ... maybe a linkage, etc
A friend looked at it and tried the old process of elimition ... unplugging the MAss Air Flow connector ... trying it ... then the TPS on the throttle body. He suspected one or both. So I replaced them... happy to get the sucker started without revving uncontrollably. But the pedal was sticky, the idle speed too high and when you press the brake pedal ( and nothing else ) the car stalls, putt putt putt kerplunk. Starts up again tho. but impossible to drive like this. So I gets me a code reader .. follow the directions and this is what I get now
P0441 Evaporative Emission system Incorrect Purge Flow ( this is an easy one even for me ... the engine light came on last time I fueled up - gas cap was not turned enough ) no brainer
P0122 Throttle / Pedal Position Sensor A Circuit Low Input
P0101 MAss or Volume Air Flow Circuit Range / PErformance
P0222 Throttle / Pedal Position Sensor B Circuit Low Input
P2119 Throttle Actuator Control Throttle Body Range / PErformance
P2112 Throttle Actuator Control System Stuck Closed
P2422 Evaporative Emission System Vent Valve Stuck Closed
Puzzling since whatever broke started working again spontaneously last time. I figure, it cannot be all the above at the same time .. perhaps one of the early sensors?
Toyota - Camry :: 2005 - Rear Calipers Stuck Open And Rear Brakes Not Working And Rusted
I have a 2005 Toyota Camry that we purchased 14 months ago. When purchased it had bad brakes so the dealer replaced the rotors and calipers at their expense. A month ago I took the car in for a routine oil change and was notified that my rear calipers were stuck open and that my rear brakes were not working and rusted. The rotors look hardly worn, the one on the passenger side has some deep grooves in it and the driver side is pitted. We feel that we had poor work done when the brakes were replaced and that the back never worked. After the brake job was done we would get some "chinging" noise in the back brakes and I had them inspected twice and they said everything was fine. But now we find out they weren't fine.
View 8 RepliesToyota - Tacoma :: TRD Wheels Binding Up?
I have a 2013 Tacoma TRD with 18k miles, totally stock after driving awhile intermittently the front left wheel has been locking up like I tapped the brake just on that wheel. I've taken it to Toyota and they cant duplicate the problem. This last weekend I drove several hundred miles and the right side started doing it about two to three seconds after the left side for about five minutes then ran fine. It actually makes a chirping noise and slightly jerks the wheel in that direction. This has only happened going over 65mph. Since Toyota claims to have never seen this problem there basically telling Me to drive the truck until it gets worse. They checked the brakes and bearings out.
View 1 RepliesToyota - Tacoma :: Hard Starting When Outside Air Is Hot
I've got a 1996 Tacoma - manual transmission, 4 cylinder, 2.7 liter engine with close to 170,000 miles on it - owned it for 10 years and 100,000 miles. Wonderful, great truck. Except.....
It has two starting problems and I can't seem to sort them out. The first is it's incredibly hard to start when the outside air is hot. Living in San Francisco, I usually forget about this problem until I drive to the central valley to visit my mom in August. Nothing like coming out of the rest stop, trying to start the engine and then having the feeling of doooh! again!. Seems to be worse when the outside air temp is over 85 or 90 degrees and the engine has been running than sits for 5-10 minutes. Cranks fine but won't catch. When it finally catches, it's like it's really slow to fire - can't quite explain it, but it's like it's doing a lot of thinking about actually running and has to talk itself into the idea. Can take 5-10 minutes to finally get it going, but usually 30 seconds to a minute. Always worried this'll be the time it doesn't want to go. My mechanic has looked at it a few times - but it's almost impossible to recreate in San Francisco when I get home due to the lack of warm days.
Second problem is trouble cold starting. When I come out in the morning, the engine takes two or three attempts to get it to start. Once it again, it cranks fine, but it's as if there's no fuel getting to the engine. If I just keep cranking, it won't fire but if I crank it, turn it off, crank it, turn it off and crank it again it'll always catch on the second or third go. Once the engine is at temp, it seems like less of a problem and easier starting. My mechanic say's "It's an old truck and it always starts eventually, so don't worry about it."
Toyota - Tacoma :: 1995 Will Not Go Into Gear
I have a 1995 Toyota Tacoma with a manual transmission that will not go into gear. How can you tell if it is the clutch or the slave cylinder that is bad?
View 2 RepliesToyota - Tacoma :: 1998 - Wobbles At 55 Mph?
I have a wobble in steering at 55 mph and have gone thru 2 sets of tires. After 1st set i changed front struts, no luck . When i rotate tires from rear to front it goes away for 6 months and tires start to wear wavy and wobble starts.
View 3 RepliesToyota - Tacoma :: 97 - Car Has Spark And Fuel But Will Not Start?
My 97 toyota tacoma will not start. have fuel, changed plugs, has spark. still will not start.
View 2 RepliesToyota - Tacoma :: 2003 Pickup Won't Start When Hot?
I have a 2003 Toyota Tacoma pickup. I bought it used in the spring of 2009. I drove it for a few months without any problems and one day this problem developed. It won't start on the first attempt. Or it will start and then immediately die. It will take two or three tries to get it running.
I took it in to my mechanic and he couldn't find anything wrong. I got a tune-up anyway and it drove like a champ. Until the next day when the problem came back. This persisted for a few weeks more and then went away.
This last summer it started happening again and continued up through October and went away again. I think the problem seems to happen when it's hot in the summer.
Toyota - Tacoma :: Shudder And Shaking Between 45 - 60 MPH At Various Revs
My 2002 Tacoma has recently been experiencing transmission trouble. Between 45-60 MPH at various revs, the truck begins to shudder and shake. The severity depends on how aggressively I accelerate. After several weeks of this, the check engine light came on. It has remained on since, except when it flashes if I accelerate too quickly. Throughout the shuddering, the revs remain constant. By roughly 60-70 mph, the truck runs smoothly again. In a (possibly) unrelated note, the parking brake indicator is lit almost constantly, particularly in wet or cold weather, although the brake is not engaged.
View 7 Replies