Passat (B6) :: Engine Running Rough And CEL On - Misfire On Cylinder 2 And 4
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
Passat (B5) :: 2004 1.8t Running Rough With CEL On - Misfire On Cylinder 1
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 RepliesSubaru - Forester :: 1998 - Rough Running / One Cylinder Has No Compression
will it hurt my 98' forester to drive it when one cylinder has no compression? They tell me it needs a valve job for 2,500. They already put a mass air flow sensor in, and replaced plugs and wires. Still got the miss, but I need the vehicle.
View 2 RepliesSonata NF (2006-10) :: Misfire On Cylinder 3 And 6 - Running Rough When Slow Down The Car
When I'm driving and get above 50-60 I will get the Check Engine Light. Check the codes It shows 6 ---300, 303, 306, 300, 303, 306. When I slow the car down it is running rough, almost like it has a miss.
I reset the computer while this is going on and the engine smooths out and it runs correctly until I keep my pedal down and then it kicks the exact same errors.
Here's strange part number one: Once I get down to about a gallon or two of gas in the car everything seems to run fine. I have plenty of power, no codes and the car runs fantastic!
Strange part number 2: Very occasionally When I get in the car in the morning to go to work, the car is a bit difficult to start. When it finally kicks over, it is immediately running rough. resetting the computer with the engine running does not seem to stop the rough running. If I turn off the engine and let the car set for a bit it will start and run fine, with the exception of the first problem mentioned in this thread. There is no code while it is running rough, but when the Light kicks on as per the first issue mentioned, I have an additional code -- 335. This car has been excellent up until the last few months when this issue developed.
Passat (B6) :: P0303 (misfire Cylinder 3) / P0299 (underboost)
I've got two error codes that are persistent. The underboost code will be fixed (I HOPE) when I replace the diverter valve which is currently sitting in my trunk.
But I'm getting a persistently intermittent P0303.
Here's whats going on:
-Some mornings, I can start the car and get a very minor rough idle, it seems to miss very occasionally.
-Some mornings, PERFECT Idle.
-Some mornings, Flashing CEL, very rough idle, P0303.
It seems to go away after about 30 seconds to a minute regardless. Sometimes ver minor rough idle comes back on hot start, but not enough to set a code.
What I've done:
-Replace spark plugs. (all 4)
-Replace offending coil with brand new one.
Still having the same issues!
Can these two codes be related, and once I replace the diverter valve, things will be better?
Nissan - Sentra :: Code P0303 - Cylinder 3 Misfire
It keeps reading the code P0303 "cylinder 3 misfire". All coil packs, fuel injectors, spark plugs have been replaced. The exhuast smells normal. The oil is the correct color(maple syrup color, NOT milky). It's not blowing through coolant. Compression test came back normal. It's not the cat converter because the exhaust doesn't smell like rotten eggs. The car is sometimes hard to start. it hesitates/stumbles and shakes really bad. It feels like its not getting enough power.
View 10 RepliesSanta FE SM (2001-06) :: CEL Came Up With A Code P0303 - Cylinder 3 Misfire
I got a check engine light. I went to Auto zone to get it read & they came up with a P0303 - Cylinder 3 misfire. Since I bought the vehicle a couple of months ago, I don't know when the plugs were last changed, so I decided to change them. However . . .
Is there a secret to getting the plug boots & wires out of the hole and off the plug without wrecking the wires?
Camry :: 2004 - Getting P0303 Code / Cylinder 3 Misfire
I have searched but with no solid answer..
What I got - 04 Camry, 231K, never had issues, do all my maintenance myself, brakes, plugs, oil etc..
#3 Cyl misfire..
Possible causes
Plugs, - Has been about 2 years since I replaced
Coil - Bought car new in 04, never replaced
Cat - never gave it a second thought
fuel injector - put techron by Chevron just about every oil change, I know I missed one here and there..
burned exhaust valve - say it aint so...
poor compression - I have to rent a tool...
defective computer - I don't think so..
Celica :: 2000 1zzfe Engine Was Running Rough - Cylinder 1 Misfire
Okay so last year i bought a 2000 celica gt manual with 50,000 miles, and currently has 67,000 miles. A few days ago I started to notice the engine was running rough and then about 10 miles later the chack engine light came on. I promptly went to the auto parts store to read the code. I was informed I have a cylinder 1 misfire. Naturally i replaced the spark plugs with NGK iridium, reset and rechecked engine code. Same code. Next i swapped the coils from 1 and 2, reset and rechecked. same code. I then swapped fuel injectors from 1 and 3, rest and rechecked. Same code. So now i am a bit stumped.
Only faulty equipment prior to this incident would be 2nd gear synchronizer. Only applicable above 5,800 RPM.
Chevrolet - S-10 :: 1996 - Running A Bit Rough / Irregular Idle / Cylinder 1 Misfire
My 1996 S10 2.2 liter pickup has been having some 'issues'. Truck has been kind to me over the years, but now is running a bit rough. It has an irreguler idle and continues to run this way through all speeds. The blinking code reads "cylinder 1 misfire". I did all the basics. I changed the plugs and wires, ignition coils and fuel filter. Here is where is gets tricky, after changing the fuel filter, it ran great again. Then it started to run rough again later that day. I thought I somehow clogged up the new filter, so I removed the new one for inspection. Realizing there was nothing wrong with it, I reinstalled. Truck ran great again. Went out to drive it to work a couple hours later and it started fine, then after about 10 seconds of running, it went back to the rough idle.
View 19 RepliesFord - Taurus :: 2005 Started Running Rough - CEL Came On / Cylinder 5 Misfire Detected
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 RepliesFord - Explorer :: 2003 - Misfire On Cylinder 8 / Running Rough At Idle And Under Load
126000kms on 03 explorer 4.6 truck started. Running rough at idle and under load.... Code came up for cyl 8 injector. Replaced injector... problem still there. Switched cop and plug with another cyl and plug.... same code and cycl 8 is definitely not working. Would a generic problem always affect i cylinder. I even checked wire clip on for injector... it appears ok. There is power to injector wire clip.
View 5 RepliesGTI 337/20th Anniversary :: 2004 GLI 1.8T - CEL Came On / Code P0303 Cylinder 3 Misfire
So I have a 2004 Jetta gli 1.8turbo and my CEL came on last night from normal driving, after it came on it still drives the same. I had it scanned for codes and got the p0303 cylinder #3 misfire. wondering what could be the solution for this? I dont think its the coil pack because I had them changed at the dealer from the recall about 2 months ago (anyway to check?) Also I have 97,000 miles on my car and my last oil change I used 0w-40 oil. I know this is probably not the best oil to use at this mileage but I had an extra 5 quarts of them laying around so I decided to use it.
View 24 RepliesChevrolet - 1500 :: 1997 - Code P0303 / Misfire On Cylinder 3
1997 chevy k1500 ... I have a misfire on cylinder 3 that i cannot figure out the cause. The idle is rough, backing out after starting is very rough, it seems to pick up at higher rpms but once the truck upshifrts to the next gear it shakes like a leaf in fall. within the past year the engine was rebuilt all new seals a new fuel pump, new injectors, new everything practically. so far i have done the following:
compression test results:125-130psi
fuel pressure test results: 50psi once primed, 50psi with engine running, no immediate pressure loss after engine is shut off
new spark plug wires
new spark plugs
replaced all four o2 sensors
Sierra :: Cylinder 3 Misfire Only Under Hard Acceleration / Code P0303
So my 2001 5.3L truck has 206,648 miles on it. Over the years, it's been serviced every 5K with the only big repair being head gaskets which were done about a year ago.
Two weeks ago, I hit the gas to merge into traffic and the SES light started flashing and I could tell there was a miss. I got off the gas and a few moments later, the light went out and the miss was gone. I pulled the code and it was P0303 so I change the plugs, wires, and the coil pack for Cyl 3 fuel filter and ran a double dose of Sea Foam through the gas tank.
Bad news is I still have the problem. The truck drives fine; in fact, I pulled my bass boat 75 mile round trip yesterday. Everything is OK till you hit the gas hard to merge or to go up a big hill or pass someone. When you hit the gas hard, SES starts flashing and there is a miss. I also noticed the valves ping loudly when the SES is flashing. The only code it's giving me is P0303.
Could this be a bad injector not delivering enough fuel at higher RPM/under load? I was going to swap injectors and see if the miss moves. Any tips on popping those injectors out?
Ford - Taurus :: Misfire Code For Single Cylinder P0303
01 Taurus, 3.0 pushrod motor. Single 6 pack style coil. I replaced worn plugs 2 months ago for misfire. Car seemed to run fine. Now, I have misfire again. Code is for single cyl, 0303. Would u expect plug to foul, or bad wire, or possibly bad coil? I don't know how these ford coil packs fail. Can u lose 1 or more spark outputs with them?
View 11 RepliesGolf IV / Jetta IV :: Catalytic Code / Cylinder 3 Misfire P0303
I own a BMW not a VW! My 19yr old daughter purchased her first car a few months ago, an '03 Jetta 2.0L with approx. 170,xxx miles. Just after she got it we pulled a P0420 code, but it ran fine so we haven't worried too much about it. I've cleared that code and after about 2 weeks it will come back. Last week it started to have some issues with rough idle, stumbling/hesitation. I pulled the codes yesterday an in addition to the catalytic code is a cylinder #3 misfire P0303. I thinking the 2 codes are not related. I'm assuming the typical things to look for on the misfire are coil, wire, plug? Looks like the coil on this engine is a combined unit so no switching coil packs to see if the miss follows a bad coil pack.
View 4 RepliesCorolla / Matrix 2009-13 :: 1.8L - Code P0301 And P0303 Misfire On Cylinder 1 And 3
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
Santa Fe (DM - 2013+) :: Engine Fault P0303 Cylinder 3 Misfire Code
We got our latest Santa Fe computer email and it warned of an engine fault. The car itself was not flashing any warnings though. Took it to the dealer and they said OBD was throwing a P0303 cylinder 3 misfire code. They shifted the ignition coil, and replaced the injector and seal before resetting the code. They had the car for 3 days though. Car was not running rough or anything else you would expect from this type of issue. Still trying to figure out why we got the email with no indication of trouble from the car itself.
View 3 Replies