Subaru - Outback :: 2001 - Misfires On Right Side Only - Faulty Cylinder 1 / 3 And 5
I just bought a used 2001 Subaru Outback L.L.Bean, and the check-engine light is on due to misfiring in cylinders 1, 3, and 5 (right side only). I thought I was getting a pretty good deal even given the CEL risk, but the car is at the mechanic now and he is stumped and telling me I have to take it to a dealer service center.
This is a 6 cylinder with a timing chain. Plugs were replaced and computer reset and the light came right back on. There are no spark plug wires, and I read that the coil packs rarely fail. The engine runs smoothly and seems to have power, but since I just bought the car used so I'm not sure how much power is normal. It has 122k miles.
What could be causing misfires on one side of the engine only?
Subaru - Outback :: 1999 - Driver Side Window Shutters?
I have a 99 Subaru Outback Limited. Since I bought it five years ago (93k miles, now 133k miles) the drivers window, when all the way down, will "jutter," moving up and down just slightly; there is also a clicking sound and the up button won't work. The only way to get the window to move up is to click up and down on the window lock switch, which always works. I replaced the window master switch assembly in the drivers door panel, but that didn't fix the problem. One mechanic, at 100k miles, told me assuredly that my alternator was bad, but I've driven it for 28k miles and 3.5 years with no problem so I don't think it's the alternator.
View 2 RepliesSubaru - Outback :: 2004 - Right Side Headlight Stopped Working
I have an 04 outback wagon with the right side headlight that has stopped working. I put a new bulb in but it still doesn't work. I tried swapping the fuse and the relay from the left side light but it still doesn't work. All the other lights on the car work. When I was poking around the connections with a meter the light flashed on/off a few times. Could this be a connection problem or something wrong with the rear headlight assembly?
View 1 RepliesSubaru - Outback :: Burnt Rubber / Oil Smell - Leak From Hose On Left Side
We noticed a burnt rubber/oil smell coming from our '01 Subaru Outback, no engine lights were on. When I looked under the hood, all the fluid levels looked good, but I noticed on the left side, about two thirds down the side of the engine, there appears to be a leak of gooey brown oil? from a hose running up over the engine. Do you think this is the source of the smell? What this is, how much it will be to fix or if we can safely drive it to the mechanic (we are about 45 min from town)? See photos here: [URL] ... I tried to zoom in slowly so you could get an idea of the location.
View 5 RepliesSubaru - Outback - Noises :: 2006 - Loud Rumbling Coming From Rear Side?
I have a 2006 Subaru Outback. When I start it, it makes a constant rather loud rumbling noise that seems to be coming from the rear of the car. I can feel a little vibration through the steering wheel, but when I put the car in neutral the noise/vibration goes away.
View 10 RepliesSubaru - Outback :: Leaking Brake Fluid On Driver Side Front And Rear Tires
Recently I took my 2006 Subaru Outback wagon on a trip in the mountains. I parked my car in the driveway overnight and noticed oily fluid on all of the tiresand on the ground in the morning. The fluid spill was worse on the driver's side front and rear tires, but was noticeable on the passenger side as well. I did not notice an odor to it. I used the brakes alot on the way back down from the mountains..... I have taken this car places where I have used the brakes a whole lot but have not noticed this before. How bad is this? Is it possibly "normal?
View 5 RepliesSubaru - Outback :: 2002 - Slow To Accelerate When Going Into Right Turn
I have a 2002 Subaru Impreza Outback Sport with ~140,000 miles on it. Recently, it's started having a problem, where when I make a right hand turn, it fails to accelerate until the wheel is straight...as if it's revving but not catching/accelerating until I've straightened the wheel and am headed straight onto whatever road I've just turned onto...does that make sense?
It tends to happen more at 1st start up in the morning...and then, once its warmed up it's not as bad, but still present. Left hand turns I don't notice it...maybe because they aren't as sharp? Also, fyi, the check engine light has been on for a while, but I know this is due to the catalytic converter..and am saving up to get that replaced.
Subaru - Outback :: 1997 - Lurching In Slow Tight Turns
97 Outback, 143 K, auto. 2.2. When in a tight turn in a parking lot or doing a U turn, the car lurches, like my p.u. does when in 4 wheel drive. Not as strongly, but it does not feel right. There is no CV joint noise, tires seem equally worn. The seller says it is tires, my experience with 5 different soobs says no and I never carefully match tire wear, ( I do not replace all 4)If it is not tires, what might it be?
View 11 RepliesSubaru - Outback :: 2004 - Growling And Squealing / No Power Steering At Slow Speeds
My 2004 Outback power steering was growling and squealing, but it was working ok at the time. I decided to replace the power steering pump before it completely failed and 3 hours later I was done. the growling and squealing was gone. However, when I backed the car out it was hard to steer at first. When I got going it all worked great, until I turned at the corner... hard steering again. When I got around the corner and up to speed everything is great again. The problem did not go away with time. Every time I turn at idle there seems to be no power steering. What is going on?
View 6 RepliesCamry :: 2002 - Clunk / Rattle In Driver Side Front End When Go Over A Small Bump At Slow Speed
I have a clunk/rattle in the drivers side front end when I go over a small bump at a slow speed. The dealer said it was the struts - they replaced them along with the upper support thing. Noise still there, next they said it was a worn motor mount - noise still there --
View 1 RepliesToyota - Camry :: 2002 - Clunk / Rattle In Driver Side Front End When Go Over A Small Bump At Slow Speed
I have a clunk/rattle in the drivers side front end when I go over a small bump at a slow speed. The dealer said it was the struts - they replaced them along with the upper support thing. Noise still there, next they said it was a worn motor mount - noise still there --
View 3 RepliesSubaru - Outback :: Loud Drone Noise At Cruising Speed
I get a loud noise from the rear of my 2005 Subaru Outback, 67k miles.(No it's not my dog Pete)Starts as a WHOP, WHOP, WHOP that speeds up as the car speeds up 'til it's a loud drone at cruising speed. I thought it was older tires but changed those Saturday. No effect.
View 1 RepliesSubaru - Outback :: 1999 - Dragging Feeling / Sound When Went Over A Speed Bump In The Park
While driving my daughter home from daycare yesterday I went over a speed bump in the park and immediately noticed a dragging feeling / sound.
After some inspection, I determined that either my spring broke or the spring broke free from its mount on the strut and was now rubbing the back of my tire.
Anyway, I've heard of the springs breaking on these cars, and I need new struts anyway, and it's older to begin with, so I set about ordering a complete strut / spring replacement for the front.
On 1aauto I found this set, part number 1ASSP00874. They seem dodgy about whether this part is intended for the Outback as well as the Legacy. I can find sites that sell parts that claim to fit one or the other or both. In this case they seem to claim both.
I know the Outback trim was slightly raised from the regular Legacy, but I can't find any other parts.
Subaru - Outback :: Misfire At Idle After Heavy Braking?
About a month back my wife and I were on our way home from dinner and when we exited the interstate I heard an awful rubbing sound coming from the engine compartment. I wasn't quite sure what it was or how to describe it. I was concerned it was the timing belt right away. I limped it home sputtering and misfiring and listened for a moment before shutting it down.
The next day I checked all the accessories. Nothing wrong there, so I realized it must have been the timing belt. I began striping the rest down and confronted carnage. One of the bearings had gone on an idler pulley and the gear was riding the bolt. the belt had moved out of position and began to cut into the backside of the plastic cover. By some miracle it hadn't completely snapped or jumped timing.
I replaced all pulleys, the tensioner, the water pump, and the belt. After my buddy and I got it back together it seemed fine aside from a slightly rough-ish idle for a day or two, but then the misfire got quite bad. I chugged it up to my wife's parent's place. We borrowed a car from them, and then I went into repair mode again. I reasoned that perhaps the plugs had fouled when the belt was messed up initially, so I replaced the plugs. Didn't have wires on hand. Fired it back up. No bueno. Same misfire and chugging. Still borderline driveable.
So, I tore down the belt again to find that the intake cam on the passenger side was about 5 teeth off. Seemed further out than my friend and I would have left it, but I got it lined back up within a tooth and put it back together. Still no good. Still misfiring. So we tried it a couple more times. One of us started to doubt the cause, but I talked him to try with one more reset. This time I wanted to get everything absolutely perfectly lined up. We did. I fired it up. Silky smooth, ran like a sewing machine. Put it back together and everything seemed fine. For a day or two.
The misfiring began again. It bothered me that I hadn't managed to take care of the plug wires. I had the codes pulled and I had a steady misfire on ... I think it was 4. I replaced the wires on that side and everything was back to normal. Silky smooth operation. For a couple days.
I was on my way to work and had to brake very hard to avoid an accident. Like from 70 to 0 wheel-lockingly hard. Immediately a misfire at idle returned. Doesn't seem to be an issue when not at idle, but it's hard to say. I guessed that it was the plug wires from the other side. I replaced those today, gave it an oil change. Still misfiring. I dropped by autozone. Codes read - misfire everywhere but 3, and I'm guessing that maybe a sensor for 3 is just messed up. The coil pack looked suspect, and I thought I'd do the PCV valve while I was at it. After replacing both the misfires continue.
I've yanked the battery to encourage the computer to reset. I'm at a loss at the moment. The only think I can guess is that perhaps my new tensioner is poop and I've jumped a tooth or two somewhere? I'm looking for guesses and wild theories here. Anything to try. I'm going to reconnect the battery shortly and if it's still misfiring, which I'm assuming it will be, I'm going to have codes pulled again.
Just to head this one off at the pass - I believe I got extremely lucky and did not damage the valves with the timing belt nonsense. Compression seems good, and I doubt it would have ran as well as it did as long as it did with valve damage.
Subaru - Outback :: 2006 - Started Shuddering At Idle
I have a 2006 Outback XT, which recently started shuddering (like it wants to stall) at idle... At least that's how it started. I noticed it for a few weeks but with no check-engine light, and no error codes cropping up, I kind of ignored it. It then started to stall at idle. Took it to my local guy, who checked all the simple stuff: vacuum hoses, mass air flow sensor, he even removed and cleaned up the throttle body. But the problem persists.
I guess the part that really has me puzzled is the lack of a check-engine light or an error code. With how computer-regulated cars are nowadays, I'm baffled as to how this isn't causing some alarm to go off.
Subaru - Brakes - Outback :: Anti-lock Braking System Engaging Noise When Speed Gets Low 5 - 15 MPH
I recently had my wheel hub and bearing replaced. The mechanic said I might hear a little noise with the brakes but they'd work. Turns out that noise is the Anti-lock braking system engaging every time I use the brakes. It happens when the car speed gets low, maybe 5-15 mph. Also, if I'm driving slow in a parking lot or something, and let off the gas, that change in speed sets the ABS system on too, without my foot being on the brake pedal.
I've also noticed sometimes when the weather is very cold, the ABS light will go on and the ABS brakes won't work; just regular brakes. Is this something that I'd be able to solve at home? Could I possibly bleed the brake lines to check for any air ( although braking seems fine ) , busted fuse for the system, anything else to check before asking the mechanic?
Subaru - Outback :: 2000 - Fast Idle On Start And Severe MPG Drop
I have a 2000 Subaru Legacy Outback with 208,000 miles. Last Oct I had a complete tune up done on it: fluids, filters, spark plugs, etc. Ever since then, the gas mileage has dropped from getting around 390-400 miles off a full tank to 290-300 miles off a full tank. I have tried carburetor and fuel injector cleaners and nothing is working. At this same time, it also started idling at 1750 rpms every time I start it, dropping down to around 750-900 rpms after I put it in gear. The timing system was replaced about 7 months earlier. So far the repair shops can't find anything wrong. I also just had the transmission rebuilt and it's still idling fast.
View 4 RepliesSubaru - Outback :: 1996 - Rocky Idle And Some Smoke Coming From Exhaust At The Manifold
I have a 1996 subaru impreza outback. It is now dead. Billowing white smoke, coolant coming out of the tailpipe, terrible rocky idle and some smoke coming from the exhaust at the manifold. (assuming it cracked from the harsh idle) I'm pretty good with cars but I've never taken on a head gasket problem myself. I have time to fix it, I just don't really know if it will be worth it. Should i just replace the motor w/ a scrapyard motor? Should I take this opportunity to rebuild and upgrade? I have a crappy chevy to get me around in the meantime. Should I give it a try or just scrap it. I paid 800 bucks for this car and it has 220k miles. No major problems until now. New alt a few months back. Previous two(only two) didn't have any problems at all. I feel like it would be worth it.
View 17 RepliesSubaru - Outback :: Rough Idle And Lots Of Vibration After A Timing Belt Change
My wife and I recently bought a 2005 Subaru Outback 2.5 XT with an automatic transmission. Last week, we had the timing belt changed by a mechanic I've gone to for the past four years and trust a great deal. He changed the timing belt, drive belts, water pump, pulleys, tensioner and a few hoses, and everything seemed to go off without a hitch. After picking up the car, though, we noticed that the idle seemed much rougher than it had in the past. We can't tell if it's also rough during driving, or when the car is in park or neutral, but there is definitely considerably more vibration when the car is stopped in drive and idling--you can feel it throughout the car. I haven't noticed it until the car has warmed up.
I asked my brother, who is a mechanic in another state, if he had any thoughts, and he said it could be that the belt is off a notch, a vacuum leak or an unplugged sensor. I brought the car back to the mechanic today to see if it he could fix it, and he said that the CEL would be on if it was a vacuum leak or unplugged sensor, and that the car has an automatic idle that the belt change would not have adjusted. He asked if the vibration was getting any better, since when the battery was unplugged it would take the computer awhile to relearn the correct idle, but we've driven it a few hundred miles and it hasn't gotten any better. I left the car with him to take a look at it, but he just called and said he couldn't find anything wrong.
I want to chalk this up to us imagining something, but we both have no doubt that there has been considerably more vibration at least when the car is idling since we picked it up after the timing belt change. Is there anything else that it could be or that I should ask my mechanic?