Subaru - Impreza :: 2009 Going In Reverse When Put The Car In Drive
I bought (in November 2012) a 2009 Subaru Impreza. On a couple of occasions, when I put the car in Drive, it started going in reverse (in a flat parking lot). Each time, I put the car back in Park, turned the ignition off, started up again and it seemed fine - till yesterday. I was in a parking lot again, tried putting the car in drive and it went in reverse! A few times in a row, till I got so close to the vehicle behind me that I had to call roadside assistance... What's going on??
View 4 RepliesSubaru - Impreza :: 2001 - Hard To Get Into Gear And It Would Not Move In Reverse / Neutral Or Drive
I had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
Subaru - Impreza :: Puff A Little Wisp Of Bluish Smoke From Exhaust During Manual Shift
I've seen more than a few Subaru WRXs puff a little wisp of bluish smoke from their big exhaust during a manual shift and was wondering what this means. Throttle, clutch, puff throttle. I was following a guy yesterday on a back road and saw it several times, and that's not the first one I've noticed.
View 3 RepliesSubaru - Impreza :: 2009 / 2.5i Manual Transmission Makes A Clunking Binding When Turning
My 2009 Impreza 2.5i manual transmission makes a clunking binding when I turn. What the issue is it goes away and comes back.
View 1 RepliesSubaru - Impreza :: 2008 - Intermittent Grinding Rotational Noise
I've got about 88k miles on my 2008 Impreza 2.5i manual. The last 30k miles on it have been rather rough (~60 miles a day stop-and-go highway traffic). Somewhere around 80k I developed a leak in my clutch hydrolic line that lead to a clutch replacement around 82k miles (I had a few leaks simultaneously so diagnosis of the clutch line took longer than optimum). I also had new break pads installed around the same time, tires rebalanced, alignment, and one new ball joint on the front driver-side wheel. Anyways, after this work I had a noise develop that I've had checked out twice and has yet to be diagnosed.
I am getting a grinding noise that occurs with both front breaks but at different, specific, reproducible points in the tire/rotor/etc rotation. It also only occurs with mild break pressure (most noticeable during a gradual, easy deceleration). The frequency changes with speed, so I know it is rotation point specific. Heavy break pressure does not generate the noise. The noise is also the most noticeable after the car has been at rest for a number of hours, and lessens the longer I've been driving continuously (but never goes away completely). I have not noticed much change as a result of moisture, and I live in Colorado so our humidity is at a minimum. I've also had my rotors checked to make sure they aren't warped, and I've been assured that my break system looks good and clean.
Ford Transmission :: 4r70w - No Reverse When Backing Out Of Parking Space Or Shudder In Reverse
2000 F150 Lariat, XC, 2WD, 5.4L, 4R70W
I don't know if this all started right after I got back from towing a 3500# lathe + 2000# trailer back from Texas a couple weeks ago or if there might have been some slight symptoms before. I do know that this really got bad a couple days ago and I haven't driven the truck since then.
So, here's what is happening. I noticed a few days before that when I would back out of a parking space, the truck didn't seem to go right into reverse. It was as if it was in neutral, but as I was reaching to jiggle the gearshift lever, it would engage and I could back out just fine. All forward gears, and shifting, have been fine all along, including lockup. I kind of wondered if the shift linkage had somehow moved and was on the edge of being in the right spot, so I was going to have a look at it one evening soon. Then a couple days ago, I went to back out of a parking spot at work and it wouldn't go anywhere.
Just acted like it was in neutral. Put it in drive and it engaged just fine, then back to reverse and nothing for a few moments before it finally engaged. Then, as I was backing up, it acted like you might expect a limited slip that was not slipping to behave. But, that was right before I put it in drive and went home. After I got home, I tried it out some more and found that in reverse, it just wouldn't go anywhere unless the truck rolled a little bit. I don't know if the rolling really had anything to do with it or not, but the driveway is on a slight incline, so it happened, and then the transmission would engage. But, when it did start to back up, even straight, at first it acted like it was under a load, then when it started to move, it bucked really badly. Put it back in drive and all seems fine.
There are no codes set. Trans fluid is full, and doesn't smell or look bad. I've searched for reverse shudder, and other stuff, and there are threads about the TC, about no reverse at all, and a bunch of other stuff, but nothing like this that I found.
Subaru - Forester :: Standard Transmission Not Going Into Reverse
Sometimes the Subaru standard transmission just does not want to go into reverse. I don't see a pattern here, but when it happens I have to double clutch it, or hold the clutch peddle down and move from first to reverse.
View 3 RepliesSubaru - Legacy :: 1993 - Automatic Transmission Won't Reverse
Reverse stopped working after it's been driven for a while. It works when it's cold. I'm actually hoping this was caused by my stupidity (though it may have nothing to do with the problem). A while ago I wanted to change my oil, but opened the auto transmission plug instead. I decided to put new trans. fluid in it. I thought I would add trans fluid until I could see it on the dip stick. After the problem with reverse started I tried to again read dip stick but can't tell where the level is, so I decided to drain trans. fluid to measure it. Owner's Manual calls for 8.8 qts. Drained fluid measured only about 4 qts. I added more. Now it looks like dipstick shows it ~2 inches above the full/hot mark. Questions:
1) Would fluid level affect reverse and not forward (with which there is no problem)?
2) Is method of draining trans. fluid & measuring it a valid way of telling how much is in it, i.e. would all... or most... fluid drain out so the 8.8 qts. in the owner's manual should be added back in?
3) Am I misreading the dipstick? I've tried letting it set for 4 or 5 days, but still fluid seems to smear high on the dipstick.
Subaru - Outback :: 2001 - Transmission Does Not Shift Out When Put In Park
My 2001 subaru outback wagon when put in park doesn't shift out of that position unless I access the little hole for releasing the shift module and put it into gear. What is the problem? The fuse for the transmission is good. outside fuse box.
View 1 RepliesSubaru - Legacy :: 1995 - Reverse Went Out But All Other Gears Fine - Bad Transmission?
I have a 1995 Subaru legacy wagon, 176K miles. The reverse went out about 10 months ago; all the other gears shift fine and it runs great. Do I have a bad transmission or could it possibly be some kind of switch or solenoid? I have searched the net for hours and keep coming up empty.
View 1 RepliesLS / MKZ :: Transmission Shift Error Displaying When Car Shifted To Reverse
2002 LS V8 162K Miles. Its been sitting in the garage for 10 days. ...went on vacation. Started her up and let it idle down. Shifted to reverse and transmission shift error displayed. Went back to P. Waited a minute. Shifted again and she was hard jumping into the gears. The error went away. Drove it around and it seems to shift fine. Opinions?
View 4 RepliesFord Transmission :: Reverse Shift Bogging Down The Engine
I've got a 1994 F-150 with the 4.9 straight six. The transmission is the E40D.
In drive, it shifts silky smooth. In reverse, it acts like it's bogging down the engine.
I only recently got the truck. It's had a fluid and filter change, and is full on the stick when hot.
I didn't notice this problem until I replaced the engine thermostat. It was stuck open, so I replaced it with a 195 degree Stant unit.
Should I let the engine control computer re-learn this engine? I've fixed bad vacuum lines, too.
I've heard tales about the electronic transmissions. This one has 145K on it.
Subaru - Legacy :: 2008 - Driver Side Clunking Noise Occurs Mostly In Parking Lots At Low Speeds
I have a 2008 Subaru Legacy Spec B. It is a great car, and I am very happy with it. However, it is making this noise and no one can figure out what it is. I have taken it to the dealership three times and the never hear the noise, and they can't find anything wrong.
The noise occurs mostly in parking lots at parking lot speeds. When I got over rough pavement or speed bumps, I get a clunking noise in the front drivers side wheel well. It sounds as if something is broken or loose at the top of the strut, right at the top of the strut tower. I do not hear the noise on smooth roads or at highway speeds. I can get it to happen in certain parking lots, but the dealer would not go to those places.
Recently I started to get another noise out of the same area. When I back down my driveway (slight down hill grade) and I get towards the bottom, I turn the steering wheel clockwise almost all the way so that I back to the right and can pull out to the left. When I get to the bottom at full turn, I hear a loud clunk and I can feel the car shift around a bit. I can repeat this over and over by pulling back in and then backing out again. It only does it when I back up to the right, not to the left. Today, It did it again but I was on a flat surface, which I had not noticed before. I backed to the right, turned the wheels fully to the right, and it clunks. It also clunked two more times when I shifted into first and started to pull forward out of the turn, almost like it was hanging up on something.
The dealer looked at the car three times. The last time they replaced the stabilizer bar links and bushings, but it made no difference. They say everything is tight and looks normal with no leaks. I am thinking it is either a front axle or front strut that is bad, but they can't confirm. The struts are really expensive on this car, so I don't want to replace them on a whim.
Important details: This is a 6 speed manual car. Turbo 2.5L boxer 4. AWD, with 68K miles. Issue was first noticed about August 2011, seems to be getting worse recently.
What this could be. I love this car, as it is a monster in the snow, which will be flying soon, and I really don't want to be driving with something broken.
Chrysler - Shifters :: 1987 - Auto Transmission Does Not Want To Shift In Reverse
My son has a 1987 Chrysler 5th Ave. The transmission (auto) does not want to shift in reverse. It does go in neutral and forward. And it drives well forward. How to fix this?
View 1 RepliesGolf IV / Jetta IV :: 09a Transmission - No Reverse / Car Doesn't Shift From 1st To Second Properly
Bought a 2003 golf gti 1.8t as kind of a project. Car had no interior no exhaust and some shifting issues. To fix the shifting issues rather than replacing solenoids I just got a rebuilt valve body. After installation the car still doesn't shift from 1st to second properly and now I don't have reverse. (It's an 09a transmission)
View 1 RepliesFord Transmission :: Hard Shift And Clunk When Shifting To Reverse
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 RepliesVolkswagen :: Transmission - Grinding Noises From Transfer / No Reverse And Hard To Shift
I have a 97 jetta trek that is having problems. Grinding noises from transfer , no reverse, hard to shift, loud winding noise. I think it's may be the trough out baring thing from what I'm reading.
View 6 RepliesChrysler - Towncountry :: Transmission Not Working Properly When Shift Into Drive From Reverse
When backing up in reverse I come to a stop and shift into drive. About 60% of the time it slams into gear (Drive). It feels as if someone rearended me. It's a 2012 Chrysler Town and Country with 40K miles. 2 dealers worked on it, reprogramed the computer and replaced 2 seloniods and the problem is still there. What is wrong but said thats typical on that 6 speed. What to do next?
View 2 RepliesFord Transmission :: 1970 F250 - Slow To Shift Going From Neutral To Reverse Can Take Almost 30 Sec When Hot
I have a 1970 f250 with a factory 390 (vin verified) and a C6, I believe the transmission was rebuilt but have no way to verify. It works fine while cold and mildly warm. Once heat soaked it is very slow to shift (going from neutral to reverse can take almost 30 sec) and leaks profusely from the front. I can not tell exactly where the leak is. Could this be a case of just having too much fluid or is there a more serious concern? The dipstick does read high but level ground in my area is hard to come by so the accuracy can be questioned. If it does have to much fluid, do I just drain the pan, re-install and let it run till hot and replace fluid as needed or should I drain and replace with 3 qrts prior to starting?
View 7 Replies