Golf/GTI VI :: Error Code 000136 - Fuel Rail / System Pressure Too High
So I've gotten this error code a few times now but never a CEL nor does the car drive any diff.
1 Fault Found:
000136 - Fuel Rail/System Pressure: Too High
P0088 - 000 - - - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 0
Fault Frequency: 1
[Code] ....
Taurus :: P0193 - Can't Find Port On Fuel Rail To Get Fuel Pressure
I cant find the port on fuel rail to get a fuel pressure reading.it is nothing like my tarus.saw astem sticking up on front right of rail but it has some kind of covering over it. It is a 2005 freestar with the 3.9 motor.
View 5 RepliesJeep - Cherokee :: 1987 - Starts Immediately If Relieve Fuel Pressure At Fuel Rail
I have a 1987 jeep cherokee with inline 6 and multi port injection.
Sometimes this vehicle only starts when hot
Some times only when it cold
I have recently fixed the fuel leak.
When its hot or cold and not starting if i relieve the fuel pressure at the fuel rail, in most cases it will start immediately. However if fuel pressure relief does not work. I disconnect the vacuum line at the what looks to be the EGR valve or the pressure regulator at the front end of the rail, then usually starts right away.
I have not tested at this time to see if the fuel pump is failing nor have i tested fuel pressure. I am trying to narrow down the problem to one specific part. There is no problems with cranking. There is spark - coil, plug, dist cap have been replaced.
It seems the problem is with fuel delivery of sorts. It was mentioned that sometimes the heat from the engine could be heating the fuel rail to a point which turns the fuel into a gas not allowing it to atomize.
LeSabre :: 1987 - No Pressure At Fuel Rail
I am getting no pressure at the fuel rail. Relay seems to be ok, so I am assuming the pump just failed (in the driveway luckily). Before I drop the fuel tank, I would like to confirm I am getting voltage back to the pump. I cannot fine any wiring in or under the car going to that area! How to find that circuit as close to the pump as possible and still accessible without dropping the tank?
View 1 RepliesElantra XD (2001-06) :: Relieving Pressure In Fuel Rail
I picked up a Haynes manual for the engine/head removal. It has the procedure for 2003 pressure release by unplugging the fuel pump and running until it dies. Unfortunately the car does not run. I do not know what to do now.
View 8 RepliesCaravan/Voyager :: 1999 Cannot Get Started - No Pressure On Fuel Rail
A friend has a 1999 Caravan with the 3.0L engine. He couldn't get it to start and to make a long story short, I checked the fuel pump relay and fuse and they were good but there was no pressure on the fuel rail. Turning the key I couldn't here the fuel pump come on and determined the fuel pump was bad.
I changed the fuel pump and fuel filter put in 1/4 tank of gas and turned the key, and it turned over but wouldn't start. I can audibly hear the fuel pump come on for a second or so, and feel the vibration when I put my hand on it, but there is still no pressure at the fuel rail.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Rail And High Pressure Oil Cross Over
Next mods are for the fuel rail cross over and the high pressure oil cross over. I see the unused ports will come in handy.
Fuel delivery? any specialty mods to run the fuel lines? I see it's a #4 ORB fitting. Anyone ever use a "T" or a splitter off the fuel bowl to have a quad line set up?
Saw the FRx from RiffRaff .... not sure how it eliminates air from the system 7.3L Diesel Fuel Rail Crossover? (FRx) 99-03 Powerstroke
Ford Fuel System :: Location Of Check Valve That Maintains Fuel Pressure On The System?
I have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
Accent RB (2012+) :: Code P0087 - Car Won't Go Over 60 Mph
Got a code p0087 on my 2012 accent (manual). The car won't go over 60 mph and has trouble going over 3,000 rpm. Car won't turn on unless I pump the gas for several seconds.
View 1 RepliesFord Fuel System :: 1989 F150 - Hot 28 Psi Fuel Pressure Shuts Off?
for the past week we have been trying to figure out what is wrong with our truck. We recently bought it and it ran fine. Then got in a minor accident just a fender bender and it started acting up so I got towed to garage. First it would run when cold, but when hot fuel pressure would drop to 28 psi.
So I put new fuel pump, it started but still did the same thing hot 28 psi fuel pressure shuts off. So I put regulator on it, then had 0 fuel pressure won't even start. So got a another regulator thinking I got a bad one, still 0. Checked relay, there fine. I'm gonna check lines and see where fuel stops at but everything is new on it.
Ford Fuel System :: 1988 - Fuel Pressure Drops Off Fairly Fast When Turned Off
Working on a 88 Ranger 2.9L 5-speed ext cab. The fuel pressure drops off fairly fast when turned off and I'm pretty sure that the check valve is bad. My question is, which pump has the check valve? It is a single mid tank set-up and has a pump in the tank and on the frame.
Pressure is fine while running. about 30psi @ idle and 40psi with no vacuum on the regulator. The pressure drops off within a couple of minutes which causes it to have to crank over for a bit to rebuild pressure and start.
It looks like the frame pump is readily available while the in take pump is special order. I just need to know which one has a check valve. I'm thinking the in tank pump, but I hate to waste money for the wrong pump.
Pressure drop rate
30 psi @ shut off
25 psi @ 1:05 min
20PSI @ 2:30 min
15psi @ 4:45 min
still dropping
Ford Fuel System :: 1988 F250 Stalls - Random Fuel Pressure Loss?
I have a 1988 Ford F-250 Lariat, 7.5L 460, four-wheel drive. I have two fuel tanks on it, and I've been having a really annoying, obnoxious problem with it lately. After running it for a while, I noticed that I keep losing fuel pressure, and the truck stalls. When I try to start it, it does nothing but roll over. It just won't start. I've changed the fuel filter, I know both fuel pumps are working (I turn over the key, I can hear front, back, and high pressure pump attached to the left side frame rail kick in.) It's Fuel Injected, not EFI, hence that third pump. The problem happens a lot, and it's random. I could drive for 100 miles, stop to get something to eat, come out, and it won't start.
I thought maybe it was the fuel pressure regulator, but I don't think that's the case because it still runs. I would assume that if the regulator was bad, it wouldn't run at all. I also thought that maybe it was the relay, but according to some mechanics I spoke too, if I can hear the pumps kick in when I turn the key over, then the relay is fine. The only thing I could think of is that it might be the fuel selector switch. Maybe it's going bad, shorting out or something. When I flip the switch though, it switches between fuel tanks, and the gauge reads how much fuel is in it from the sending unit.
There's a schrader-type valve up by the fuel injectors. When I push it in, it barely squirts any fuel out, if at all, so I know the pressure is low. When I push it in on a good day, it sprays out like a water fountain. Just tried starting it again - no good. Pushed on the valve, it spurted out some fuel pretty well, but still won't start. Occasionally tries to, but ultimately won't. I know the spark is good, checked the plugs/distributor cap. Can't get the sucker to start.
Ford Fuel System :: 1989 F250 Fuel Pressure Drop Quickly Under Heavy Load
I am a newbie as far as fuel injection. The original issue the truck had was no fuel. I tracked down the issues to a blown fuel pump relay and a melted inertia switch. I jumped the inertia wires with a new fuel pump relay installed and the truck ran at an idle and up to 3500 RPM when stationary. If the truck is going up a grade or needs more throttle it will start to lose fuel pressure and end up stalling. I had the fuel pressure gauge connected to the schrader valve on the fuel rail and had 30-35 PSI when idling. It runs good under light load on the throttle.
Under heavy load it starts to drop quickly and if you back off the throttle it will stay running some times. I changed the fuel filter and also replaced the high pressure pump on the main frame and it still has the same problems.The original pump was pumping about 13 ounces of fuel in the 20 second test that the repair manual suggested. I have even placed a jumper wire direct to the new fuel pump to bypass original wiring and possible problems. When it stalls under load (No Fuel pressure) at the schrader valve you can hear the fuel pump running but there is no fuel pressure.
If I turn off the ignition for a few minutes and then turn the key back to the on position it will start to pressurize and then start and run at an idle. I even replace the ignition switch as it was a little temperamental. I have not changed or checked the fuel pressure regulator as it is a pain to get to at the back of the engine. I do not want to spend a fortune tracking down this problem since the truck may not even pass its smog inspection and may be a parts truck only.
67 F-250 4x4
73 Crew 4x2 (4x4 Soon)
89 F-250 Super Cab 4x4
Volvo :: Lost Metal Clip Connecting Fuel Line To Fuel Rail - What It Is Called
I have a 1994 volvo 850 turbo wagon. While replacing the pcv breather system, I dropped a little metal clip that attaches the fuel line to the fuel rail with a t25 torx screw. I can't find the clip. What the part is called or where it can be found?
View 1 RepliesFord 6.7L Power Stroke Diesel :: 2011 - Hard Acceleration / Code P0087
I'm getting a p0087 on a hard acceleration new low pressure pump new fuel filters run the pinpoint test in the pced is fine and passes the high pressure test with the ids? Not sure where to go from here?
View 5 RepliesFord 6.7L Power Stroke Diesel :: Truck Idling High - Code P0087
This morning I went to go to the corner to buy something, I knew it was colder than usual, -12F. I did not plug in the pre-heater last night. I let the truck idle for 15 minutes before moving it. It was still idling high. The P0087 code is the only code popping- is this just because of the cold temp? I haven't owned a diesel since my '79 Rabbitt, and this engine is as different from that as night is day. this didn't happen yesterday but it only got down to -2F and warmed up to about 18F.
View 6 RepliesFord 6.7L Power Stroke Diesel :: HPFP Failure - Code P0087 And P21b0
My hpfp just blew up 2 weeks ago. I'm still waiting to hear if my ford extended warentee will pay for it. What was weird for me was I had a p0087 code thrown about an hour before the p21b0 code. I had a 5sec warning of reduce power, then pull over now message, then it died before I could get over. All service down by ford, 48k miles on my 2011. I'm not happy that the truck left me on the side of the road with the 5th wheel in tow. Having a second failure? Not sure if I want to keep the truck now or not. Sounds like even the newer trucks are failing as well. I would have thought they would have this fixed by now.
View 4 RepliesCamry :: 2002 - No Start / Check Fuel Pressure System?
I recently purchased a 2002 camry 2.4l 198k miles from a friend. His mechanic said engine was on it's way out so the next day after work the car didn't turn on so he thought his mechanic was right. So he told me about it and said it needed a new engine so me being a guy that likes to purchase broken down things I got it. I had it towed home and was going to mess with it on my free time.
So today I got under the hood and first thing I did was spray starting fluid in the intake. It turned on and was running good then shut off. First thing I'm thinking is fuel pump. When I disconnected the fuel line to the fuel rail and primed it it had fuel gushing out.
So now I want to check if the fuel pressure is right. I know the 5th generation camrys have a different fuel system that's kinda new to me. ( I know I'm out dated, I mess with diesels and older Hondas) so my question is what steps or processes of elimination steps should I take to keep this car running? How do I test the fuel pressure system on this car? Oh and before I purchased the car he said he "super filled up" the tank.
Ford 6.0L Power Stroke Diesel :: High Pressure Oil Rail End Caps
I was watching a tv show a while back, I cant find the episode but I think it was performance tv, and they had a 6.0 L expert on there and he was saying they see a lot of high pressure oil rail end caps come loose and or pop out. He was saying that they tap/thread the end of the oil rail and put a threaded in cap? Does it make any sense, can it be done, is it worth doing?
View 14 Replies