Santa FE SM (2001-06) :: 2004 - Low Beams Don't Work
My low beams won't work. High beams and fog lights work just fine. We just replaced both bulbs a few months ago so the chances are pretty slim that it's a blown bulb.
I've checked the fuses and relays. I switched the low beam and high beam relays with no luck. Still no low beams.
Santa Fe (CM - 2007-12) :: Low Beams Not Working
I have a 2007 Hyundai Santa Fe. At first just the left head light went out, the next night I tried to turn my headlights on and they didn't come on. The high beams work but the low beams doesn't. I've replaced the bulbs from assuming they went bad. That didn't work, so I checked out the fuses, all of them were good. I don't know what else to check.
View 3 RepliesSanta Fe (CM - 2007-12) :: Low Beams Not Working Suddenly
I've seen a couple posts about low beam lights not working suddenly, but no real fixes to the issue. Looking for an actual fix that worked.
My lights; running, fog, high, and low beam, all worked yesterday. This morning when I try to go to work, all but the low beam lights work. Nothing was done differently, all fuses and relays appear to be intact, and the bulbs appear to be fine.
Golf IV / Jetta IV :: 2001- Headlights Malfunction - Only High Beams Are Working
So I bought an 01 GTI last week with a decent amount of things pre-modified including a Jetta front end swap? Anyway the guy I bought it from knew absolutely nothing about what had been done to the car other than the fact that there was an HID kit installed and it was set up to run high beams only.
I figured I'd remove the HID's until i drop some cash on a pair of nice projector housings. I removed them and plugged up some nice sylvania bulbs as per the OEM standard 9007, and figured I'd have no issues... They are still stuck on high beam only... What could be causing this?
Santa FE SM (2001-06) :: 2004 - Low Beam Headlights Stopped Working
Low beams don't work. The fuses are fine (under the dash, and in the engine compartment) and the bulbs look good. The fact that both went out at the same time has me wondering. One post on this forum for something not related mentioned a headlight relay behind the fuse panel?
View 9 RepliesSanta FE SM (2001-06) :: 2004 - AC Quit Working When Blowing Cold
It was blowing cold and stopped. Minutes later it started again and then stopped. This went on for a week and then stopped altogether. Car has 190,000 miles. Is it compressor, clutch or relay....
View 5 RepliesSanta FE SM (2001-06) :: 2004 GLS Cruise Control Just Stopped Working
I have a 2004 Santa Fe GLS that the cruise control just stopped working. It will not turn on when I press the ON button. Could it be a blown fuse? I recently had a new AC compressor installed. Could it be related to that? Maybe something didn't get plugged back in?
View 1 RepliesSanta FE SM (2001-06) :: 2004 - Door Locks Stopped Working At Once
I have a 2004 Santa Fe, recently all the door locks stopped working at once. When I use the Key Fob The Blinkers flash like they are supposed to but it does not lock/unlock the doors. The panic button also works. When I use the key in the door it only unlocks that door, meaning when I double turn the other doors do not lock/unlock. Now that this happened all at once I do not believe all the actuators broke at once. Is there a fuse or a relay that might of broke or blown?
View 8 RepliesSanta FE SM (2001-06) :: 2004 4WD Idles Rough / Brake Pedal Not Working
I have a 2004 Santa Fe 3.5L 4WD. It's been running rough on occasion for quite a while now, but it's only been an occasional thing. I replaced the front passenger side axle and went for a test drive and the vehicle was barely running. I put the throttle to the floor and it does nothing more than idle. I barely made it home and am afraid to pull it out of the drive. I started it up this morning and it seemed to be idling just fine. I pushed the brake to put it in gear and it started stumbling. When I put it in gear, same thing, pedal not doing hardly anything.
The check engine light did come on and I had a buddy bring down a scanner to check it. I don't know if these are Hyundai specific codes or not, but here's what he pulled: P1110, P2127, P1173, and P1192. I'm thinking throttle position sensor, but am unsure. I've put a lot of time and money into this vehicle lately. I've spent some money and a lot of time trying to figure out why it was showing abs and traction control lights. Turned out to be the exciter ring on the axle was broke.
Malibu :: 2004 Only High Beams Working After A Replacement
Driver side low beam was burnt out. I replaced the bulb with a new one then no low beams would work, high beams work. Turning on manual switch and I checked fuse 7 & 10 fuses which were okay still no lights.
Could it be the low beam relay? The passenger side was working. Do they only come on when it is dark enough as I can't remember if they are running lights and worked in daylight?
Ford Super Duty (1999-2016) :: 2001 F250 - No High Beams And Dash Lights Not Working
I have an 2001 F250 SD with 7.3 Diesel. Headlight switch failed and I replaced it. But now I have no high beams and my dash lights that light the dash up don't work. Gauges, fog light, low beams all work fine. Fuses checked. Multi function switch checked. What to do next?
View 1 RepliesSanta FE SM (2001-06) :: 2003 - Blinkers Not Working But Hazard Lights Working Fine
I have a 2003 santa fe and the blinkers are not functioning but the hazard lights are working fine. I checked the fuse and that is fine. Is there someway I can take apart the handle assembly where the switch for the blinkers are? Also, sometimes they would work and other times they wouldn't so that seems like a loose connection somewhere. The indicators for the blinkers on the dash do not work either so there has to be a problem giving power to the switch.
View 8 RepliesSanta FE SM (2001-06) :: Radiator And AC Fan Not Working
I have a 2006 2.7 gls awd santa fe ,the alternator bearing went bad and got stuck took the alternator to a repair shop to get fixed, put it back on the santa fe the alternator worked just fine now i have the radiator fan and ac fan not working, I turn the ac on and none of then work I wait for the car to heat up and nothing happens I check the radiator fan by connecting it directly to the battery and it works fine ,i have swap the horn relay with the radiator relay and it is working fine. I will check net the fuses, then the thermostat and later on the temperature sensor.
View 29 RepliesSanta FE SM (2001-06) :: Rev Counter Not Working
I'm a new owner of a 2005 santa fe 2.4 16v cdx manual petrol. The rev counter is not working but the speedo is engine runs and tick over fine.
View 3 RepliesSanta Fe (CM - 2007-12) :: Low Beams Keeps Going Out
2007 Hyundai Santa Fe ....
Annoyingly my low beams keep going out. I can replace the bulb and it works for a short while but than again fails. Because of this when driving at night I have just been utilizing my high beams, but since inspection time is coming up I need this resolved. The fuse is intact, and I don't want to waste another set of bulbs if I can avoid it. I am uncertain if it is related, (as it should only affect the tail lights in theory...) but this issue first showed itself a month or so after getting my trailer hitch wiring installed. What would the next suggested check be?
Santa FE SM (2001-06) :: Speedometer Working On And Off Specially When Going Over 65 Mph
My 2003 santa fe has Issues w the speedometer. It works on and off, specially when going over 65mph.
What do I need to do to fix this problem? Is it a DIY fix?
Santa FE SM (2001-06) :: Odd Vibration At 45 Mph - 3.5 Liter AWD Not Working
I recently purchased a used 04 3.5 liter SF. I don't think the AWD system is working. The car has a bit of an odd vibration at 45 mph but I thought this was due to the new all terrain tires on put on the car. There are no check engine lights on in the car and it otherwise drives straight and well.
It just snowed here for the first time in CT this season. I took the santa fe out and tried to start on some hills and it would just spin the front tires and slide backwards. The rear end would not kick in at all. It didnt matter if I had turned traction control on or off. When I look at the snow there are only two front tire marks that spun down into the snow. The rear tire left not skid marks.
There are no strange sounds coming from the rear differential. I know the Santa Fe 3.5 use the Borg and Werner magnetic clutch system and is usually front wheel drive. Is it possible that clutch system is worn out or is it an electrical issue with the front not sending the rear a signal to engage the rear diff?
Santa FE SM (2001-06) :: Power Steering Won't Working
I am having a power steering problem with my 2006 santa fe, been going on for a couple weeks and I am stumped on what is wrong with it, what I noticed is turning to the left or right and very hard to turn and sometimes it will be fine and other times its the left or right.. What could be going on here? there is no leaks or noises noted, it has 242,000 kms on it. fluid is full but a little brown and smells a bit burnt. I know it will need a flush but would that be the solution or would it be something else?
View 15 RepliesSanta FE SM (2001-06) :: Speedometer / Tachometer And Gas Gauges Not Working
We have an intermittent (now more regular) issue on our 2005 SF of the instrument cluster (tachometer, speedometer, gas gauge, temp gauge) sitting at zero - no motion whatsoever. In the summer months, the gauges came on after a while of AC being on, which I thought odd. But it just happened here in October (and the temp is just around 5C/41F) so a temp issue is unlikely. No OBD codes that we know of, all the fuses are fine, and while we did have a PCSV issue earlier this year, it did not seem to affect this particular issue with the gauges.
Threads such as the one below seem to say that it is the speedometer that is wacky... 01 Santa Fe Speedometer Not Working! , and the general solution to the problem/issue is to replace the vehicle speed sensor (VSS) and associated gear mechanism. And on a different thread, Input Output Speed Sensors , it was suggested that the problem could be addressed by changing the input and output sensors.