Prius (2004-09) :: Code P3022 (bank 12 Low) And POA80 (Replace HV Battery)
Was crushing around and received the red triangle, check engine, DSC, etc. pulled two codes from my scan gauge P3022 (bank 12 low) and PoA80 (replace hv battery). Car was in limp mode, engine running full time, battery gauge showed hv battery depleting.
After reviewing other stories online, seems as though I might be looking at a new battery. Car is 2006 with 112,000 miles.
Prius (Gen 1) :: Code P3006 Appearing After Battery Replacement
I have a 2002 primus and got the p3006 code.
Engine would Rev and got all the lights. I figured it was the battery and decided to get a Dorman replacement. I replaced the battery but turning it on I would get the p3006 code after a few seconds. No lights at that point. I would drive about 10 miles and would get all the lights and a second p3006 code. I would clear the code and it would get rid of lights and car would operate normally.
Sometimes the lights would come on and the brake light would also come on and the engine would rev. sometimes when that happened I would get code p3012.
could the battery be OK and it be some other problem? I thought p3006 was the bad battery code.
Prius (2004-09) :: 14 Blink Code On Hymotion LED - 12V Battery Replacement?
I'm getting the 14 blink code on my Hymotion LED indicating that my 12v battery is needing replacement. My question is that the car seems to run fine with the exception of my mileage is low. I'm ordering the Optima replacement. Can I still drive around for another week without worry?
View 2 RepliesPrius (2004-09) :: All Caution Lights Came On After HV Battery Replacement - P0AE0 Code
Well, just replaced my HV battery, hooked everything up (I think) and tried to start it. ALL the caution lights came on and stayed on. This is the code that showed up on the reader. P0AE0. The battery was refurbished and I changed over my Computer module and the contact posts. Everything is tight, and I compared my pre-takedown pics to the post-repair work and it all looks correct.
View 3 RepliesPrius (2004-09) :: 2002 Toyota Keeps Dying With 3191 Code After 12V Battery Charge
My 2002 Toyota Prius keeps dying (triangle of death and OBD Code 3191) after running smoothly for a few seconds each time I start the engine. Clearing the DTC code allows restart. But the check engine light and triangle of death keep returning after a few seconds.
It has been doing all this since I recharged the 12V battery (which had been drained completely by a dome light left on for 3 days). Initial attempts to recharge the 12V battery were causing current spikes at charger, and (relay?) clicking sound under the hood. So I disconnected positive battery cable and charged the battery in isolation, then reconnected it to the vehicle after charging was complete.
When I reconnected the recharged 12V battery the vehicle (honking horn) alarm went off. But that stopped when I unlocked door with key. It may not be related, but I'm also hearing a fan-like sound (under driver seat) when ignition key is in run position. I don't recall hearing that sound in the past.
Passat (B5) :: 2002 - Key Fob Battery Replacement?
I'd like to know how to replace the battery in the key fob for my 2002 Passat Wagon. I looked in the manual but I could not find it and it says that the dealer should do it. I am aware that sometimes the fob may need to be re-programmed but my wife's key works perfectly so I will assume that the battery has gone out. The key works just fine when used manually.Also, what kind of battery does it take??
View 2 RepliesCamry :: 2002 V6 Stalls On Idle Instantly After Battery Replacement
Just got the battery replaced on my v6 Camry, had no problems before it. After replacing the battery, I drove about a mile to another stop and parked the car. Noticed it vibrating and the idles very low. I restarted the car and it wouldn't stay on. Car will turn on fine, RPMs will go a bit above 1k and drop down and turn off in about 5 seconds.
Today morning I started it and it seemed fine (cold start). Idles were about 1K on a cold start. Drove around about a mile and came home and the car stalled. Same as above, it'll start up and stall within 5 seconds.
I took it for a drive (about 25 miles) so the car can re-learn everything and took a stop at Autozone. Same thing there. Didn't stall on the way because I didn't have to stop, I was on the highway. One of the sales guys looked at the car and told me to try out a new MAF Sensor. Installed a new sensor and the car died off again within 5 seconds. Checked the readings of the MAF sensor (old and new) and they both read fine.
Brought the car back home (about 35 miles total driving after battery replacement) and it'll still stall as soon as you stop. To keep it going, you have to hold the brake and hit the accelerator very lightly to keep the idle in the middle of 0 and 1 or shift into Neutral and do the same.
No CELs on the car, car drove perfectly fine before the new battery. New battery tests good, even went to the extent of putting my old battery back in (Drove about 35 miles on new battery, replaced and drove 35ish miles). Car has just short of 100k miles. Regular services are done at Toyota at about 5-6k.
Subaru - Forester :: 2002 - Turns Off While Driving After Battery Replacement?
My Forester was dead one morning and when I went to jump it off my pick-up in a hurry I did the age old palm to forehead and didn't pay close attention to the posts on my pick-up battery. Crossed the posts.So I began working through the common known issues.Replaced the main fuse. Didn't Start.Replaced the battery. Started... Car shut off while driving. Did not sputter out, simply cut out like turning the key off.Started right back up.Positive battery cable was loose. Replaced it.Grounds are good.Alternator output is good.So here are some more details on the car shutting off.
This last time as I was coming home from the store and the car shut off on the main road through town. I had enough momentum to get off to the side of the road. I tried to start it and it would turn over. Normal turn over sound but the car wouldn't start. I took a minute to check other electrical things in the car with key in the "on" position. Radio worked. Dome/interior lights worked. But then I noticed something strange. None of the dash lights came on (Car is not started but key is in "on" position). The windows did not work either.It started after about 5 minutes time and I made it home, forgot to roll the windows back up. Turned key to "on" again and couldn't roll the windows up. Got out of the car and came back after about 5 minutes, turned key to "on" and the dash lights came on the windows rolled up.
Ford - Focus :: 2002 - Stalls In Park After Battery / Alternator Replacement
Last week, I brought my 2002 Ford Focus (automatic transmission) to the mechanic to have an oil change and to have the motor mounts and cabin air filter replaced. Before I brought the car in, it was fairly loud at idle--which had been going on for a couple of years and which I attributed to the worn motor mounts--but had otherwise been running fine.
When I went to pick it up after the repairs, the car would not start. The mechanic ran some tests and told me that the alternator was overcharging the battery. The battery could no longer hold a charge, so both the alternator and the battery needed to be replaced, which the mechanic did.
I thought at first that everything was OK after the battery and alternator replacement. Because I almost always turn my car off immediately after putting it in park, I didn't realize what was happening and that it was a problem... but in retrospect, I realize that ever since I got the car back from this second set of repairs, the battery light has flashed on during the split second between when I shift to park and when I turn the ignition off.
Yesterday, I took my car back to the mechanic because it stalled when I was in the parking lot at work. (I realize now that it must have happened just after I shifted gears, probably into park.) Since that was the first time it had actually properly stalled--rather than just a quick battery light flash just before I turned the car off--I had not yet made the connection between the stalling and the shifting to park, so all I told the mechanic is that it stalled on me when I was slowing to a stop. I'm pretty sure the first time it stalled was the first time I let it idle for more than a half-second in park before turning off the ignition.
He kept my car for a full day and ran a lot of tests on it. He was unable to make the car stall during multiple test drives (though, to be fair, I hadn't told him that the trigger for making it stall was shifting to park because I didn't realize it myself yet). There were no engine codes, the check engine light was never on, the fuel pressure is OK, and the throttle body position sensor, the idle air control valve, the ignition system, and the fuel system were giving no abnormal readings. When I asked, he told me that they did perform an idle-relearn procedure after replacing the battery and alternator. He returned the car to me and told me to come back if it stalled again.
Tonight, when I got the car home, it started to die immediately when I put it into park (the headlights dimmed and the battery light came on). I was able to reproduce this a second time as well. Fortunately, it does start back up just fine.
I plan to take the car in for repairs again, but I'm wondering if I should go back to the same mechanic. My questions are:
1) What is likely to be causing the problem?
2) Is it something that is likely to have been caused by incompetence when installing the new battery and alternator or doing other repairs, or could it be a coincidence (I was willing to believe the first coincidence of the battery and alternator dying while the car was at the repair shop, but I'm having difficulty believing a second coincidence)?
3) Whether or not the problem is likely to be the mechanic's fault, is it something that a thorough check on their part should have discovered?
Ford - Explorer :: 2002 XLT - O2 Sensor Replacement - Code PO136
My 02 Explorer (XLT, 4.0) decided to throw a new code today. PO136, O2 Sensor Circuit (Bank 1 Sensor 2).
While it may be a wire issue, I still plan to replace the sensor. So the question is;
Can I get to it from under the vehicle or is there an access panel under the console like on the 2nd gens?
I have the sensor on order and plan to get it done on my days off next week.
Mitsubishi - Montero :: 2002 - Code P0506 After Timing Belt And PCV Replacement
2002 Montero sport 3.5V6 , Miles: 130,000. Bought recently drove home over 2 hour drive no issues, Recent work: Timing belt (preemptive). All Serpentine belts, PCV valve (after timing belt job I noticed oil in exhaust)It gave a P0506 code and idling at 500 rpm after the timing belt job, found some oil in exhaust. Got the PCV valve replaced. That solved the oil in exhaust issue, but the code has come back. Drives ok, no issues, no smoke.I am going to clean the throttle body and install new air filter, today and take it on a highway drive (clean oil residue from cat). I had the timing belt work done at a very trusted place, but this time their game was not so good. Boss on vacation, new location and their work was somewhat careless not their usual style.
View 11 RepliesPrius (Gen 3) :: After Battery Replacement Car Went Dead
Came out one morning went to start car, daily driver, 180k, completely dead. Figured since battery was never replaced went to Toyota and got a new battery. Left on vacation came back 3 weeks later, installed battery, went to start car and still completely dead. No dome light, no brake lights, no head lights, no anything.
Checked battery, full charge under load. Tried to jump start (correct polarity) using my 4x4 Dodge Ram 2500
Never had a single issue, warning light etc. I am going to get my multimeter out on Monday and check the visible fuses.
Prius (Gen 2) :: After Replacement 12V Battery Is Not Charging
I just got a 2004, it did have a bad 12V battery which I did replace, still not charging.But First it is making a loud noise under the hood sounds like towards the right side.when I accelerate starts at 18 to 20 miles per hour. Tried sitting still with car in gear and pushing accelerator can not get it to make the noise that way, without the wheels rotating.
View 17 RepliesPrius (Gen 2) :: 2007 MPG Keeps Dropping Besides Of Battery Replacement
2007 model Prius with 74k miles.
I was getting 45.6 mpg on the trip computer. MPG dropped a couple of tenths pretty quickly. Got fuel and put in some Techron fuel treatment. Checked 12v battery, was a bit on the weak side, so I replaced it . Checked voltage and everything was good.
While I had the battery out I let the car sit for 10 minutes to reset the ecu. Now after 40 miles I'm getting 35 mpg on the trip computer, and the ICE kicks on any time I press the accelerator pedal, even if I'm going down hill from a stop.
There is no difference in driving style, tire pressures (40 front, 39 rear), I bought the fuel at a place I normally get fuel.
Prius (2004-09) :: No Start After HV Battery Replacement
I have a 2004 prius that had a HV batyery problem. HV battery was rebuilt. After that car started ran but after shut down it will not start. It will only show red triangle, abs, vcs, yellow tire. Basically all yellow lights on dash board except check engine. Also on the MFD it shows the red car with exclamation symbol. I scanned it but shows no DTC codes.
View 16 RepliesPrius (2004-09) :: 12 V Battery Replacement Now Car Will Not Start
I just replaced my 12V battery and now the car won't start. It will take a jump and show "ready" on the dash but as soon as the car is turned off, it won't start again - no lights, nothing. I checked some fuses and they looked fine.
View 11 RepliesPrius (Gen 2) :: 2007 - Traction Battery Failure And Replacement
Received these warning lights this morning.
Just took it to a local shop and here are the codes it has thrown:
The car is running badly now -- really not wanting to drive t at all. Where I can get this fixed myself? I have no problem single charging / grid charging / balancing these things out and or replacing hopefully only "block 8" as denoted above. And yes, this is the nightmare of having you battery go out -- 160k miles right now so no chance of warranty.
Prius (2001-03) :: Red Triangle After Hybrid Battery Replacement
well I saw one other thread on this topic but no resolution. I replaced the hybrid battery like the codes told me too on my 2003 prius and it now drives great but as soon as it start it shows a problem and the red triangle stays on. No check engine light, no codes, no driving issues just a red triangle. How to diagnose a red triangle when there are no codes.
View 16 RepliesPrius (2004-09) :: VSC Warning Light Came On After 12V Battery Replacement
My 12v battery died, I tried recharging it etc, but it was dead so I took it to my local Toyota dealer and had the battery replaced.
Because I had the battery off, there was a VSC warning light, which I thought that the Toyota dealer could reset. They re-calibrated all the warning apart from one, they say that the Yaw sensor will not clear it's warning and needs to be replaced.
if I can reset this warning myself, or do I really need to replace this sensor?