Civic - Honda :: 1997 - Cylinder Head And Gasket Replacement
I have a 1997 Honda Civic that I was given by an elderly neighbor's daughter after the elderly lady went to the grocery and ended up 100 miles away when she could not figure out how to get home. The car was smogged at the beginning of the year but when I got it ran very rough and the temp went nearly to overheating on the drive home when I was stuck in stop and go traffic.I found the radiator fluid level low and an oily residue inside the radiator water bottle. I took it to a mechanic to check it out and was told it had a blown head gasket and maybe worse.
I am thinking of buying a rebuilt cylinder head and replacing it myself but I am not sure how to diagnose if any other damage could have been caused to the engine. It's hard to know but I am guessing that the engine was damaged during the 100 mile road trip due to low coolant level. It turns out short term memory loss was the diagnosis for my elderly neighbor. I filled the coolant level and ran the engine for a bit and the temp stayed normal but the rough running remains. The oil dip stick shows no signs of coolant in the oil and the coolant looks bright green when I looked in the radiator after topping it up with some water.
Any way to detect if I could be facing bigger issues like failed bearings? I am OK to do the head replacement but an engine replacement starts to get into the realm of what it would cost to get another car of the same age.
Ford 7.3L Power Stroke (1999-2003) :: Cylinder Head Fuel And Oil Rail Plug ORing Replacement
Is this job worth doing as a preventative maintenance item? I replaced the rear fuel rail plug (aka banjo bolt) o-rings because they were very easy to get to with the up-pipes out. But the cylinder head plug in the rear is pretty high up and even with the up-pipes out, there isn't enough room to get a breaker in there that's long enough and has enough movement to loosen it. The front would be easier to get to, but both accessory brackets need to come off to get to them on both sides.
As far as I know, none of them leak but they're all 17 years old... BTW in case you haven't been following, I'm doing up-pipes, injectors, turbo, rebuilt HPOP & fuel bowl, boots & clamps, etc. so I'm trying to knock out any PM items while I have it apart.
GMC - Sonoma :: Leaking Cylinder Head Gasket
I have a 1995 GMC Sonoma pickup truck with supposedly a blown cylinder head gasket. It only has 53K original miles on it. It overheated and I had it towed to a service shop. They put in a new water pump, new coolant, new thermostat, new radiator hose and did an oil & filter change. Well, 100 miles later, I noticed my water coolant was disappearing and the oil pressure was rising. I brought it back to the same shop and after looking at it for five minutes they informed me it was a blown cylinder head gasket. They said they had no way to determine this when they were doing the repairs the first time. So, I ask the following:
1-Was it proper for the shop to do the first repair without checking for a potential head gasket leak?
2-Is there some type of testing that could have been done by the repair shop to check for coolant leaks into the engine oil? 3-Would I have saved money (labor) by having this taken care of at the time of the initial repair?
Honda - Cr-v :: 1999 - Burnt Valves / Cylinder Head
My 99 CR-V has lost compression in cyl #3 and now #4, 40 and 30psi respectively. Still runs, about 10mpg or less local, 14 highway. No HP, forget fifth gear unless I'm drafting someone downhill on the highway. I've got 228k on this otherwise nice vehicle. CEL reading misfire codes galore. Anyhow, should I trust one of these outfits that will send me a rebuilt head with my returning the core or should I pay some local a bunch more for the rebuild?
View 17 RepliesGeo - Metro :: Car Smoking After Rebuilt Cylinder Head Installation
Got a rebuilt head for my metro from a very reputable ebay seller/shop, and it smokes pretty badly after installation. I checked my pcv valve and it has vacuum at idle, and the hose is not plugged. Performed a compression check- 180 on all cylinders- okay for my car. Called the shop to see if maybe they forgot to install the valve seals, and they insisted that there is no way they would forget that.
View 8 RepliesFord F-150 - 1997-2003 :: Best Way To Clean Cylinder Head?
whats the best way to clean a 97 f150 5.4 cyl head
View 2 RepliesPhaeton :: Head Lights Are Flickering
I just noticed that the headlights are flickering like crazy, both of them. I was trying to hold them from the inside but they are still doing it. I dont think they are moving.
View 1 RepliesCamry :: 2003 - Minor Oil Leakage From Alternator And Cylinder Head?
I'll be working on an 03 camry this weekend with a small oil leak coming from the alternator and headers area. I know For sure its a gasket that will need replacing but which one and how difficult is it? On the last pic there's a blue circle ;the leak is from that area.....
View 3 RepliesCamry :: Cylinder Head From 1992 To 2001 Model Will Fit 1994?
Looking for if the camry 5sfe cylinder head from 92 to 01 will fit a 94 camry?
View 3 RepliesFord F-150 (2004-2008) :: Brush Dropped In Cylinder Head
Same brush is in the cylinder. I lost a cleaning brush in the cylinder head and cant get it out. Im sick to my stomach. I had a small magenta but it wasn't strong enough to get it and any stronger wont fir thru the cylinder taper. Any suggestions besides taking it to a mechanic and pulling the head. Hers is a pic ......
View 12 RepliesFord F-150 - 1997-2003 :: Sensor Broke In Cylinder Head?
I have a 1999 Ford E150 4.2l. My cylinder head temp sensor was dangling but still connected to the sensor... the connector was loosed from the filament but was still connected by exposed metal pins.
I figured I would replace it like i did to my ECT by the Water Pump. So I pulled the connector out and it started to leak...a little. and when I put the socket on it I instantly broke the sensor flush with the Cylinder Head.
I researched on here and found many people believe the CHT gives info to the Dashboard Gauge and the ECT is used by the ECU. I thought that was correct because I had ECT readings from my scantool...and my Dash Gauge never worked. When I found the dangling CHT I figured it was never working.
So I JB welded CHT hole. figuring i would fix it properly later. I replaced the ECT and expected everything to go back to normal.. No gauge reading on dash and a scan reading with no codes.
I want to replace the CHT sensor properly. Do I HAVE to remove the manifolds. Or do you think its safe to drain the coolant and drill it out. Its easy access. Im worried about all the tiny pieces getting into narrow passage ways.
I am almost 100% going to drill out. Manifold sounds like hell and its getting cold. What sensor controls what? Can I drill it out safely?
Saab - 9-5 :: 2003 - Coolant Standing In One Cylinder - Blown Head Gasket?
A local mechanic tells me I have a blown head gasket on my 2003 Saab 9-5. He also said there's coolant standing in one cylinder. If this is due to stretched head bolts, might I remedy the problem by replacing the head bolts and torqueing to specifications?
View 4 RepliesToyota - Tacoma :: 2004 - Head Cracked And Leaking Coolant Into Cylinder 2
I have a 2004 2.7 liter toyota tacoma with 135000 miles. the head cracked and was leaking coolant into the #2 cylinder. it wasn't catastrophic and was still running with just a stumbling idle at start up when cold. That said i took it apart, found the crack and I am in the process of replacing the head at home, my mechanic did all the diagnosis work.i don't remember overheating or when the head could have cracked.
Question is.....what should i check or replace while the head is off so that i don't crack my new head??there were never puddles of coolant under the truck. I just don't want to replace my head and crack a new one.
Prius (Gen 3) :: Head Light Replacement For Toyota IV 2010
I'm looking for my head light replacement for my prius 2010 IV. if this type of headlight can be used for my prius: Sylvania Silverstar Ultra H11 HEADLIGHTS SU/2 NEW
View 2 RepliesPontiac - Montana :: 2002 - Head Gasket Replacement
I have a 2002 pontiac montana that needs the head gasket replace. Mileage is 152,000 miles with a v6 engine. I would like to get at least another 75,000 miles once the repair is done. Is it worth doing as alternative is to scrap the van and buy a new vehicle...
View 3 RepliesSubaru - Forester :: 2007 - Head Gasket Replacement
I have a 2007 Subaru Forester X Sport Model. I just passed 86,000 miles - much of that open road driving. My head gaskets need to be replaced. This seems somewhat early. I recently switched from using regular motor oil to a synthetic blend that the dealership suggested. Is there any history suggesting that switching lubricants might cause the head gaskets to deteriorate?
View 10 RepliesGeo - Prizm :: 1995 - Starter Just Clicking After Head Gasket Replacement
I recently replaced the head gasket on a 95 Geo Prizm. Now when I tried to start it, all I get is the starter clicking. I tried tapping the starter solenoid, to no effect. The only electrical that I messed with during the head gasket replacement was to disconnect the battery.
View 4 RepliesFord - Explorer :: No Response From Starter After Head Gasket Replacement
Vehicle 2007 Ford Explorer Sport Trac with 4.6L
Ok, just did a head gasket replacement. Everything is now hooked back up. Now when we try to restart the car, we get lights, but nothing from the starter. Also the OBDII code puller can't communicate with the car. Also the security light flashes very fast when you try to start.
Ford 6.0L Power Stroke Diesel :: Head Gasket Replacement?
So, I blew my head gasket and have been looking for what to replace it with. From what I've seen, just an OEM gasket would be best.? I'm also putting ARP studs in it, unless there's another brand I should put in it.
View 3 Replies