Passat (B5) :: CEL On - Random Misfire On All Cylinders
I went and looked at an 03 Passat 1.8T with 114k miles. I like the car and the price but the CEL is on, returning random misfire on each cylinder with a standard (non VW) scanner. There are no other codes. The car runs beautifully until it idles low with the car stopped or stopping; then you can feel it missing.
The coil packs and controller arms were recently replaced. The timing belt was replaced at 100k. The spark plugs and wires have not been replaced. I don't know whether the coil packs are stock or not, should I ask? The code can be cleared but then it comes back (I'm not sure how long it takes; I could ask).
I've collected this list of possible things to check, based on this useful previous post:
1. Oil overfill.
2. Downstream O2 sensor.
3. Spark plugs and cables.
4. Cam Shaft Adjuster? (maybe? there is no cam shaft code?)
5. Plugged fuel injectors?
6. Plugged catalytic converter.
7. Cam timing?
8. Induction cleaning?
Is this a good list? Are there possible troubleshooting steps not included here? Are some of these superfluous in my situation?
Lexus RX 2004-09 :: 2008 RX350 - Check Engine Light For Random Misfire On Cylinders 4 / 5 And 6
I have a 2008 RX350 with 68k on the clock. Received a check engine light for random misfire (P0300) and misfire on Cylinder 4 (P0304), Cylinder ,5 (P0305) ,Cylinder 6 (P0306). Question is what will be causing this to happen. I thought about changing the spark plugs to see if this is possibly the cause. but what else should i be checking?
View 1 RepliesGolf IV / Jetta IV :: 2004 1.8t 6speed - CEL Keep Flashing Code P0501 / Random Misfire On Cylinders
I have a 2004 Jetta 1.8t 6speed, I recently bought it from a person(my first VW ever) so just trying to fix some things on it, One thing that I'm stuck at is My CEL, it keeps flashing the code P0501 and some random misfire on my cylinders, I have reset it and they keep coming back.
when I put about 10-15% throttle it revs up fine, no misfire or hesitation until the fuel gets cut off around 5500, which is 1k below factory red line, does not hit a thing like the rev limiter where it pegs off the top multiple times just fuel cuts off.
If i put anything above the said pressure the car then begins to misfire and lots of hesitation and that's what causes those codes to go off.
I've been reading many things pointing towards the engine speed sensor or the wiring. Occasionally my fuel/temp gauge quit working but I believe that is a separate issue all together.
So really trying to narrow down what is actually causing my engine to hesitate at low rpm.
Also i might note when I'm in neutral I can go wide open throttle and the car revs fine until the cutoff and only does the bog down when it's under full load. It sorta feels like the possible misfire is due to bad air/fuel but really do not know.
Ford Super Duty (1999-2016) :: P0300 Code And Various Misfire Codes For Random Cylinders
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
Passat (B5) :: Random Misfires On All 4 Cylinders
OK. I have a 2005 Passat 1.8t fwd. Tiptronic. 105k
The symptoms i am having is random cylinder misfires on all 4 cylinders. I have scanned with vagcom multiple times and get the same codes. However, I have cleared the codes, and wen fpd a 60 mile drive on the turnpike. Not a single code. So everything is perfect as long as the car dissent have a chance to idle.
I have also driven the car while logging misfires and only get misfires at idle. Never while driving.
So much has been done to the car that is so hard to decide where to start. Ill try to go in order of events.
All this in the past 4 weeks by the way.
Took car to very experienced VW tech. Found out.timing was off by 3 degrees. So new timing belt, water pump and all. Started car, still had misfires. Noticed wetness on head gasket. And did a compression test. Very bad results. (I can't remember the numbers but they were way off from each other) So he removed the head. He said there was a crazy amount of carbon buildup in the combustion chamber. Everything was cleaned, head inspected for bent valves and everything looked perfect after cleaning. (this car has NEVER overheated by the way) He said it is very rare for a head gasket to fail on 1.8t's . So he did a leakdown test and turned out the piston rings were shot. So engine was rebuilt. All components cleaned of carbon, replaced all parts, bearings with new OEM parts. Pickup tube cleaned along with other oil lines. Turbo was inspected, and I was told it is on its way out but still has life. So that was let go for now. All reassembled and all hoses checked, combi valve cleaned, new k&n filter in stock airbox. So he told me the car is finished after all that. I was excited! Drove the car home 15 min drive, ran great. Parked in my driveway, put it in park and misfires came right back. Called him the next day and brought the car back. He looked over it and replaced the fuel pressure regulator with new. He said it seemed like a fuel starvation issue. Tested fuel pump and it was towards the low end of the proper operation value. So I had a high flow pump sitting at home brand new and I brought it down and put it in. Still misfires but a lot less than before. Also fuel filter was replaced. So next he disconnected the cat And found it was clogged. Replaced with my old Audi one, and it ran fine. And this is the first time the car idled good enough to get all the monitors set for emissions testing. So he was convinced it was fixed. Room it for a test drive and came back, parked And began misfiring again. So I was so sick of this thing at this point, I told him to replace the Turbo with brand new OEM unit. And it still misfires.
He swapped a known good throttle body into it and no difference. He also said that he started going around and unplugging sensors and the more sensors he unplugged, the better the car ran. He was curious whether the ECU was faulty. So he put an ECU from his Audi in it which had a ko4 file in it. He said it ran amazing!! So he modified an ECU from a stock Audi and that's what I am driving with now. Still same symptoms. But not as often. Also brand new bosch mass air sensor was installed as well. So this is as far as we have gotten with it and I am so sick of this car right now. But we are both determined to get this thing fixed! And after all the money I have just spent, I can't even get rid of it or I will lose a lot of money. It really sucks because I love the car and so does my wife. And out of the three 1.8t's that I own, I have never had any major issues like this.
Passat (B5) :: B5.5 AWM Idles - All Cylinders Misfire
How it all got started: [URL] .... Replaced Check Valve (06A 133 528 D/A) today, car is still idling rough, flashing CEL but it's solid/no CEL when the car is moving.
What I have done so far:
1. Replaced Turbo Inlet Pipe (Cracked at one corner)
2. Replaced D.V. (Original was fine)
4. Did Smoke Test, No Vacuum Leak
3. Replace Check Valve (06A 133 528 D/A) Above The Intake Manifold
4. Cleaned Throttle Body and All Pipes under Intake Manifold
Codes keep reappearing:
17705 - Pressure Drop between Turbo and Throttle Valve (check D.V.!)
P1297 - 001 - Upper Limit Exceeded
And All Cylinders Misfire
Car idles fine when I squeeze this hose marked in green : [URL] ....
Something I noticed before and I think it's still doing it, there is weird noise every time I shift to reverse or drive, It sounds like when you just open drivers door.
Here's the link to the sound clip [URL] .....
Passat (B5) :: Multiple Misfire On Cylinders 2 And 4
I have 2000 b5 passat with 150k on it. I've had the problem of a multiple misfire on cylinders 2 and 4. The last time it happened was about a month ago do I brought it to a vw dealership and had one of their mechanics and they told me I had a valve cover gasket leak and it was causing my coil pack to short out so they replaced my coil pack, plugs, and wires. They wanted way too much for the valve cover gasket leak so I decided to wait till I more money. The car ran great for a month or so then the misfires started happening again.
I made an appointment to get my valve covers replaced a they're getting replaced right this minute but the misfires are coming and going. One day the car runs great and the next day it's misfiring like crazy an shuddering bad. It only seems to happen when it rains or is wet outside.
Passat (B5) :: 1998 - Error Code P0411 / Misfire On Cylinders 1 And 3
So i got a 98 passat sedan used and was told it read a p0411 code. The person at autozone told him it was a cam sensor. The sensor was replaced. I know now from the manual that codes reads for sec. Air injection system , incorrect flow. It could be the vacuum lines. Now lets say it is the vacuum lines. Their is a misfire on cylinders 1-3.
View 4 RepliesPassat (B6) :: 2007 - P0171 / P0507 And Multiple Misfire Codes From All Cylinders
2007 Passat 2.0T ... I just purchased this vehicle and after about two weeks of driving it has gone bananas. I found a ton of oil in the spark plug holes, and installed a new valve cover gasket...It no longer leaks. I am getting P0171, P0507 codes and multiple misfire codes from all cylinders...
View 6 RepliesPassat (B5) :: 2001 - Emission Workshop / Misfire On 4 Cylinders And System Too Lean Codes
I am getting the dreaded emission workshop.
The codes i am getting are p0301-p0304 and p0171
Which are misfire on 4 cylinders and system to lean (bank 1).
Here is what I have done:
Got the 4 ignition coils replace, replaced the mass air flow, replaced the air filter, replace the plugs.
I just check the L wire and it doesn't have any cracks or holes
I don't know what to do next.
Passat (B5) :: Random And Cylinder 1 Misfire At Idle And Low RPM
1999 Passat 2.8L. New coil pack assembly, wires, plugs, valve cover gasket(oil in plug holes). Misfire at idle and low rpm. Driving at higher rpm's misfire seems to go away. Codes are random misfire and cyl 1 misfire. Need to know if I would get an injector code if a fault or If that motor has problem with faulty cams or springs or any other common problems. I am going to do a compression check this weekend I'll update that info.....
View 9 RepliesPassat (B5) :: Random / Multiple Cylinder Misfire Detected
What is going on with my sisters passat 2002 V6 GLX Auto 4Motion. Here is the codes:
16730-Camshaft Position Sensor (G163) Implausible Signal
P0346-35-00
16684-Random/Multiple Cylinder Misfire Detected
P0300-35-00
16688-Cylinder 4: Misfire Detected
P0304-35-00
16690- Cylinder 6: Misfire Detected
P0306-35-00
16689-Cylinder 5: Misfire Detected
P0305-35-00
I changed Both sensors and it still same problem. Car only has 40,000 miles didnt change timing belt.
Passat (B5) :: Random Misfire Only At Idle / CEL Starts Flashing
Ok. Im going to keep this as short as possible. I bought my 05 passat 1.8t AWM TIP used in 09 with 44k
At around 90k I started getting a Random misfire only at idle. And it would be a different cylinder, not always the same would come back after clearing. The RPMs would be very low like around 840. And i think it should be around 920-960. That seems to be one of the main issues. Everything on the car is stock.
So basically, If my CEL starts flashing, and I clear it, I could drive a million miles with no misfires, but as soon as it starts to idle they come back ( I do have vag-com) and know how to use it for basic functions.
This is what has been done:
July 2011:
Engine rebuild (bad piston rings due to clogged cat converter)
Timing belt Kit (Timing was off 5 degrees!!!)
brand new turbo KO3, and Oil feed line
DV
N75 valve
Fuel Pump
Fuel Filter
Fuel Pressure regulator
MAF sensor
ECU swapped out (old ECU would not go through all steps for Throttle body alignment)
So, after all this and 3 weeks later, I get the car back and it ran great the whole way home. Put it in park waited 5 seconds, and the random misfires came back. So it went back to the shop the next day.
September 2011
These things were done:
Crank Position sensor
Cam position sensor
Compression test ( to make sure he didn't make a mistake while rebuilding motor) Results were Perfect
Leakdown test
Map sensor
Another MAF
2 O2 sensors
Upgraded DV
Fuel injectors
Removed engine wiring harness and OHMed every single wire. Nothing wrong
OEM Coilpacks
3 sets of copper plugs
Throttle body was swapped with 2 others from known working cars.
Trans pan replaced fluid flushed and new trans filter
I have heard this is a fairly common thing on the B5.5 models...
Passat (B6) :: Random / Multiple Cylinder Misfire Detected?
my car was running fine yesterday. Today the check engine light came on and it started to run funny.. I checked the diagnostic code and it says the the cylinder is misfiring and that oxsygun sensor is malfunctioning. (Random/Multiple Cylinder Misfire Detected)
View 4 RepliesPassat (B5) :: 2004 - Random Misfire At Idle Like One Hard Knock
2004 Passat 1.8t 4motion ... I am getting random misfire at idle like one hard knock then every thing is ok. I also have no MIL light or retrievable codes. I checked for vacuum leaks don't see any. Change out some old vacuum check valves. Replaced oil breather hose had crack. I Changed timing sensor, timing belt and fuel filter fuel pump died changed out. The old fuel filter had something rattling around in it is that normal? Also when I get gas no matter where, 91 octane only the car idle stumbles about 5 minutes after fill up then smooths out after a mile or so. EVAP purge valve clicks some times? Haven't check EVAP canister for saturation. Fuel regulator? I haven't checked fuel pressure. Car was not starting after sitting for week end hard start took 3 to 4 tries then starts up ok for some reason that is not happening now?
View 6 RepliesPassat (B5) :: 2006 - Random / Multiple Engine Cylinder Misfire
I have a '06 Passat 3.6. I had the intake and valve cover off the other day and when I put it back together it started missing bad. The code it is throwing is a P0300/ random/multiple engine cylinder misfire. What is wrong?
View 2 RepliesPassat (B5) :: Error Code 16684 And 16686 - Random / Multiple Cylinder Misfire
I was driving along and the engine started missing really bad. The whole car was bouncing around. At first I thought I had a flat, but when I stopped I noticed it was the engine. I checked the error codes and got 16684 and 16686 --- Random/Multiple Cylinder Misfire.
I had a problem recently with the vacuum hose broken and was causing an error code. Replace the hoses and it has been fine. Checked to make sure that the hoses were secure and they are fine. Doesn't seem to me to be related. So many problems for a car with 57,500 miles
Golf IV R32 :: Random Misfires On Cylinders 4 / 5 And 6
I am getting random misfires on cylinders 4, 5, and 6. Mostly on 6, less on 5, and even less on 4. Cylinders 1-2-3 show ZERO misfires. I am using vag-com to monitor these. Mostly doing it on idle, cruise seems fine but occasionally when shifting I feel it when engaging the next gear. It doesn't buck but I feel a little hesitation. Cruising and accelerating I do not feel it. Its very strange. A couple times during extended idling I have even gotten a flashing CEL. Fuel mileage has been pretty bad ever since I got the car in December. Average tank gets me 250-270.
I tried swapping coils with 123, and the problem stayed on 456. Coils are all new since I got the car. Plugs are fairly new (under 5K) and I pulled a couple to check, they looked fine and gap was about .028. I might try a new set but my gut is telling me the problem is some where else. I would like to verify/test grounds but I don't know where the harness grounds out.
I also want to get a vacuum gauge on the FPR, or check fuel pressure at idle. I replaced one cracked vacuum line, i am thinning there might be others since there seems to be miles of vacuum line on MK4's. Also have a new fuel filter to install, mine appears to be OEM and the car has 97K.
Tiguan :: Random Cylinder Misfires On All Cylinders With Rough Idle
I have 11 tiguan 2.0T. When I start it up is runs rough below 1200 rpm. The check engine light starts flashing. The codes are all 4 cylinders for random cylinder misfire. When I go drive it around the roughness calms down but doesn't go away and the idle will start jumping up and down. It goes to 1500 back to 800. Then 1700 back to 800. It had even hit 2400 once. I have changed the pcv about 2 months ago. I checked it and it looks fine. One place said maf. I cleaned it and no change. Running out of options.
View 2 Replies