Lexus RX 2010-15 :: Loose Lower Side Molding?
I recently discovered that my lower side molding on my front passenger side door was loose while cleaning away some of the salt stains from the winter storm . how to fix it or do I need a replacement.
View 11 RepliesLexus GX 2004-09 :: Rear Cargo Door Glass Chrome Molding Installation?
How to install the rear door glass chrome molding? Do I need any special instructions?
View 14 RepliesLexus RX 2010-15 :: Passenger Side View Monitor Installation On RX350
How to install passenger side view monitor of 2010 RX350? I have bought OEM side view camera and steering wheel control button. I don't know to connect the wire. My car had navigation and parking assist already. How to install it?
View 14 RepliesSonata I45 (YF - 2011+) :: Passenger Side Chrome Molding Near Headlight Popped Out
Chrome trim on passenger side near headlight popped out some of it broken (only the pieces on the inside) any way I could salvage this trim without having to buy a new 1?...
View 4 RepliesLexus RX 2004-09 :: 2008 Chrome Body Side Molding?
My car is Lexus Rx 400h, 2008, AWD, European version.
Looking for installing this chrome "molding" under the doors?
Lexus GS 2006-11 :: Drip Molding On Right Side Of 2007 GS350 Peeling
Over the weekend I was attempting to detail me car and install my HID Fogs when I noticed that the "Drip Molding" on the right side of my 07' GS350 was peeling. It looks almost like some type of thin cheap painted tape.
Here are the pics...
When I took it to Lexus of Cherry Hill, they told me that they were "puzzled" and that a service tech that has been there since 1989 has never seen this before. Asked if the car was involved in any accidents......
The car was purchased from a lease. All service records come from Lexus w/ a clean CarFax.
Lexus GX 2004-09 :: Driver Side Door Molding Clip Missing
My driver side door molding is missing a clip. This is the bottom half of the mold and one of the clips snapped off. I've checked junk yards and they never have any GX's. Just to elaborate the clip I'm missing is on the exterior side of the door, down by the bottom edge.
View 2 RepliesLexus GS 2006-11 :: 2008 - Peeling Drip Molding On The Passenger Side
My 2008 460 has the damn peeling drip molding on the passenger side. I found a wrecked 07 gs of the same color in a local wrecking yard and I was wondering how hard it is to pull off the drip molding myself. Do I need any special service tools? Don't want to damage my car.
View 2 RepliesFord F-150 (2009-2014) :: Winch Mount Installation - Removal Of Plastic Molding?
Installed the Rough Country winch mount yesterday. One hour, by myself. Used a floor jack to lift it in place.
Only problem was removing the plastic molding which came in the spot the fairlead will be. Just a small rectangular plastic molding with a couple of bars down the middle for looks. It had two screws on top edge, and two pushpins on bottom , but also was molded with two catches on each side on the back I did not see. When I figured it out, and squeezed with just my fingers, little too hard and snapped one catch on each side. They slide into a slot and catch but wont be doing that ever again. Oh well.
As for mount, solid and easy to install. I used hand tools as the air gun would only hit one of the bolts for the front tow hooks. The other was blocked by plastic molding. No big deal.
Hidden Winch Mounting Plate for 09-14 Ford F-150 Pickup [1010] | Rough Country Suspension Systems.
Lexus RX 2010-15 :: Rubber / Felt Window Molding Pops Out On RX350
Our new (got April 2014) RX350 seems to have an issue with the rubber/felt window molding getting caught between the glass and metal incorrectly. "Pinched".
View 1 RepliesLexus RX 2010-15 :: 2011 - Driver Side Rear Door Child Safety Lock
I have a problem with my driver side rear door's child safety lock. The safety lock is STUCK/BROKEN on the lock position and i cant get it back to normal... The door could only be opened from the outside right now at all times.
I took the door panel off too see if i could do anything to make it unstuck but very unfortunate...
The safety lock is a whole module itself. I bought it to my mechanic he checked it out and said it cannot be fixed and has to be replaced and he quote/estimated me just the part alone is roughly $300?
How much the part would cost in Sewell? I tried looking it up but cant locate it
Lexus RX 2010-15 :: 2011 RX350 - Seat Belt Buckle Vibration On Passenger Side
Having issue with seat belt buckle vibration, passenger side, when the vehicle speed is between 40-50 miles/hr ? It feels like an exhaust vibration transferred through the floor connection of the seat belt. How can I get rid of it ? The vibration feels like a cell phone set on vibrating and is very annoying for the passenger.
View 2 RepliesPrius (2010-12) :: Seat Side Trim Panel Installation
The side trim panel on the passenger side seat was accidentally pulled away in the front. Checked the tabs and clip are intact, is there any special way to push that in? Or just by brute force?
View 1 RepliesLexus RX 2010-15 :: Installation Process Of Eyeglass Holder Instead Of SOS?
I wonder if I could remove the SOS system and install eyeglass holder in its place?
View 1 RepliesCamry 2012+ :: XLE - Adding Body Side Molding?
I have a '15 Toyota Camry XLE V6 Blizzard Pearl
I was thinking of adding on Body Side Molding.
How does it look in person? any pictures?
I had cars with it that I've added on after. I like the look of it either way [on or off]
Passat (B6) :: How To Remove Side Chrome Door Molding
How do I remove side chrome door molding? Do they clip off?
View 3 RepliesFord Aerostar :: 1996 - Body Side Molding?
I need a piece of the orig body side molding or something close. Where I might find something that will work? I'm reconditioning all the rockers on my white van and I need a piece on the sliding door.
View 8 RepliesFord Excursion :: 2005 - Securing Side Molding On The Doors?
Our 2005 Excursion has these side moldings (mouldings? whatever) on the doors. Plastic things, probably intended to absorb impacts from shopping carts, etc.
My driver side one is just hanging by the top. Looks to me like these are just taped on?
What I have to do to properly secure this bad boy? Should I remove the whole thing, remove the old tape, and use a whole new set of tape in both places? Does one apply the tape door-first, or molding-first?
And, most importantly, what kind of tape should I use, and where should I get it?
Camry :: 2010 - Chrome Window Molding Removal?
I would like to remove the chrome window molding around the front and rear doors of my 2010 Camry. Is it difficult to remove? More importantly, when I go to reinstall it - is it difficult to get straight like OEM fit and finish?
View 3 Replies