Hyundai - Elantra :: 2004 - Jerks When Driving Uphill / Accelerating
I have a 2004 Hyundai Elantra with 130000+ mi on it. The current engine has 96000+ mi; the original was replaced because the previous owner allowed it to overheat, blew a gasket, and apparently warped the engine itself.
I have owned this car for about 6 weeks now. The car was driven roughly 160 mi from where it was purchased to my residence; no trouble on that trip. However, within the first few weeks of owning it, the car started making a squealing noise when I turned the steering wheel. I took the car to a mechanic and had the belts adjusted. This eliminated the squealing, but I was also told that the CV boot needed to be replaced (they asked if I had been hearing a clicking noise when turning, which I had but had thought nothing of), so I also had that repair done. Problem solved. Car seemed to be running fine.
Okay, on to the current problem. Something else I had started to notice, before I had the belts adjusted, was that it seemed to hesitate a little when going up hills, and sometimes when accelerating. It was a small thing, and I attributed it to my driving style (which probably isn't the best) and the fact that my area is very hilly and the car might be having a harder time with that. Well, this problem has gotten worse; I can definitely feel the car jerking, especially when accelerating (very noticeable when going uphill). The problem also seems to be worse at lower speeds, but I'm not entirely sure that I've nailed that down.
One thing I noticed is that it seemed to become much more noticeable after the last time I gassed up the car. It seems like it's getting worse as the fuel is used up, but that's probably just a consequence of using up fuel as I drive and I'm just looking for connections where there aren't any.
Hyundai - Elantra :: 2002 - While Running Car Will Lose Power And Will Not Respond To Throttle
My Elantra has been doing this for a while: While running (idle, driving slow, driving fast, doesn't matter) the car will lose power and will not respond to the throttle. It does this a few times in a row usually and then starts running normally. When running normally it runs perfectly fine, nice smooth low idle and good acceleration.
I started by doing a basic tune up: plugs, wires, oil change, air filter. No change. I then swapped the throttle position sensor. No change. You can see the symptom on youtube here: [URL] ....
What could be causing this?
Gasoline - Hyundai - Elantra - Transmissions - Clutches :: 2002 - Losing Power When Climbing Hills
Our 2002 Hyundai Elantra is having issues. It shifts fine, no need to double-clutch. It stays in gear. Doesn't grind or anything crazy like that. It does seem like it isn't getting power to the drivetrain, and is having trouble climbing hills. This all came on very suddenly. Hubby thinks it's the clutch -- I think it may be the bushings. Though now, I'm wondering if it's something else? Since it's not having trouble shifting, should we be looking at the fuel system? Sensors? Engine seals?
View 10 RepliesHyundai - Accent :: 2008 - Radio Just Loses Power Altogether Sometimes
I've got an '08 Hyundai Accent, and the radio just loses power altogether sometimes. At first I thought it was a fuse, but then it came back on after a while. I realize it's likely a bad connection, but where specifically to look for this connection before I take the dash apart?
View 3 RepliesHyundai - Excel :: 1994 Loses Power And Stumbles Uphill Going Forward Only
I am having problems with my 1994 hyundai excel 5spd man. trans...when i drive the car it seems fine but if i go up a hill it stumbles and loses power very quickly and cant make it up the hill. It feels like the motor starts jerking and stumbling but if i put it in reverse and reverse up the same hill it has tons of power and doesn't run rough.....the car hasn't been driven much in the last 6 months or so and the fuel gauge says 3/4 full...the motor also idles good but takes a long time to warm up (like 20 mins or so even when driving it around in 75-80F weather).
View 11 RepliesHyundai - Sonata :: 2004 - Loses Power While Driving With Click And Lights Shuts Off Completely?
I was driving my Sonata this morning to work as usual. It was a wet morning but not raining. I hit a pothole (which I've hit before) going 35-40 mph. About 1-2 minutes later I was driving about 30-35 mph when I heard a click, lost power and then everything came back on. I believe during this "power loss" that I couldn't accelerate since I remember the rpm going down but I know that I took my foot off of the accelerator when this happened. I kept driving to work and about 2-3 minutes later while coasting down a hill at 35-45 mph. It happened really fast twice in a row.
Each time there was a click, the lights would dim or shut off completely (not sure since it happens so fast), the check engine light would flash, and I believe the radio turned off. Since it happened so fast (click, shut off, and back on) I didn't get to see if I could keep driving (accelerate) or if power steering was gone. I am guessing that they would be gone with my limited knowledge of what I was experiencing. I was able to drive 8 minutes to work without it happening again. I popped the hood looking for a loose connection around the battery but nothing was popping out at me. My car has 117,000 miles and has regular maintenance done. Any ways I could diagnose it further? Can O'reilleys check the code that flashed on and off if it isn't on anymore?
Elantra MD (2010-15) :: 2013 - Stereo Loses Power
13 Elantra sedan. When I turn the key to on (engine not running) The stereo turn on normally.(NON -NAV) Start the car and it turns off, no screen, no audio, just like i hit the power button. Load up the electrical system, max A/C, headlights, Etc. It turns back on like nothing happened. Voltage on the battery is 14.3 with no load and right around 14.0 when everything is loaded and i finally get it to turn back on. Do these head units have an over voltage protection? 14.3 doesn't seem that high to me.
View 2 RepliesHyundai - Elantra :: 2002 - Misfires On Cylinder 1
I have a 2002 Elantra that has been in shop 3xs for same thing. The car says it is missfiring on 1 and I have changed wires, coil pack and spark plugs with no success.
View 2 RepliesHyundai - Elantra :: 2002 - Revving At Idle
I have a 2002 Hyundai Elantra that is exhibiting some strange behavior at idle.It wants to rev from 1500 to 3000 rpm, then back down, over and over again, every two seconds or so. This does not occur when the car is in drive or reverse; it purrs along at a consistent 1200 rpm.It all started with overheating and a water pump change, which was completed and reassembled.Then on startup, we began getting this revving. We double and triple checked the timing belt. We sprayed plenty of carb/choke cleaner in the areas of the vacuum hoses searching for a leak to no avail. Whenever we hookup the OBD code reader, there are no codes.Why does my car want to challenge everyone to a drag race, and what is causing this?
View 8 RepliesElantra XD (2001-06) :: 2002 Hyundai Will Not Go Into 5th And Reverse
i have a 2002 santa fe which will not go into 5th and reverse So i have put a new clutch in and new oil ....
View 8 RepliesHyundai - Elantra :: 2002 - Turns Over But Cannot Get It To Start
Can not get it to start. Turns over. Replaced wires, coils, ECM, check fuses and fuel pump is on. Power to coils.
View 5 RepliesSaturn - Vue :: 2002 - Loses Power When Put Car In First Gear And Tried To Accelerate
My wife has a 2002 Saturn Vue with the 2.2L 4cyl engine and a manual transmission. Yesterday she started it in the morning and backed out of the driveway. When she put it in first gear and tried to accelerate, the engine lost power and the car crept along around 5mph. The SES light came on as well. She took it to Autozone and they plugged it in but did not get any codes from it. I disconnected the battery today for about an hour, reconnected it(thinking it might be a computer issue?) and then test drove it and got the same result but this time without the SES light. The engine revs just fine out of gear or when in first gear and not trying to accelerate. It seems to only lose power when under load. I'm lost.
View 1 RepliesHyundai - Elantra :: 2002 - Brake Pedal Goes To The Floor Without Much Force
Working on a 2002 Hyundai Elantra GT. 4 disc, no ABS. Problem is the brake pedal goes to the floor without much force. I bled all 4 lines, but no improvement. Rigid lines from the brake master cylinder to the rear wheels were very corroded, so I ran new lines. The old ones pretty much fell apart when I took them off the car. I also replaced the brake master cylinder. I tried to bleed the brakes again, but couldn't get much (if any) fluid pressure at any of the wheels. Yes, I found a couple leaks at the junction points for the rigid lines, but I re-flanged those connections and got rid of all the leaks. Still no real pressure when trying to bleed.
So, I tried a second, then a third master cylinder with a new attached resevoir. No improvement. I bench bled the snot out of this third master cylinder because the symptoms clearly suggest air was likely trapped somewhere in the system. I used a wood dowel to fully actuate the cylinder many times after all the air had been released while I had short clear hoses running from the master cylinder outlets into a little plastic cup filled with clean brake fluid. I wanted to make sure there was no way air could be in the MC, and no air drawn back in when I released the wood dowel.
Next, I quickly capped off the MC outlets and connected a hose to each brake line individually where they normally screw into the MC. I then let clear fluid drain through each line until it was spilling out clear of each caliper bleeder with no air bubbles. So, no lines are kinked, clogged, or contain air.
I took every precaution to keep air out of the system, yet when I push the brake pedal, there is still virtually no real pressure generated by the MC. The power booster rod is shoving the master cylinder in as it should. I don't think there's any problem with the power booster.
I've used gravity bleeding, manual "push & hold the brake pedal" bleeding, vacuum bleeding, and I'm certain there is no air in the lines or calipers. Still no significant pressure coming from the MC when I push & hold the brake pedal to the floor. It takes maybe 20-25 pounds of foot pressure, but always goes completely to the floor with all the bleeders closed. If the pedal is held to the floor, fluid slowly seeps from the bleeders. I'm used to it spraying when doing this on a healthy brake system.
Hyundai - Elantra :: 2002 - Loud Noise From Front Tires
I bought an 02 Elantra last August with 128,000 miles on it. The front tires make a noise at almost any speed that reminds me of a 4X4 with mud tires going down a highway. I have replaced the axles, front struts, outer tie rod ends and one irregular rim, and I will replace the rear struts this weekend. Varying the tire inflation has no effect on the noise. When I got it aligned, the mechanic told me they had to swap the front tires to get the alignment within spec, and the uneven wear should cancel out. That was 3,000 miles ago and the noise level hasn't changed. The front tires still have 5/16 of tread on them. Should I keep waiting it out, get new tires, look for some other cause, see if there's a hole in the firewall I can soundproof, or what?
View 2 RepliesHyundai - Elantra :: 2002 - Low Beam Headlight Burned Out - Bulb Replacement
The headlight on the driver's side has burned out, should i move the battery in order to get to the bulb?
View 3 RepliesHyundai - Elantra :: 2002 - Rough Idle And Misfire When Hot / Intermittent Hesitation When Accelerating
2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
Hyundai - Elantra :: 2002 - LED Versus Halogen Headlight Bulbs / Wipers Shudder Across The Windshield A Lot
Looking for a rundown on LED versus halogen headlight bulbs, especially output and life? Stock halogen bulbs using 55 watts have a 4000K output, and I notice the Chinese imports' output is 3200-3500K. Does that translate into less bright? Also, the windshield wipers shudder across the windshield a lot unless there's a huge amount of rain--changing to new blades didn't make any difference.
View 5 RepliesHyundai - Sonata :: Jerks Decelerates To About 20 Mph
When my 2009 Sonata decelerates to about 20 mph, the car jerks. This happens when my foot is off the brake. What's going on and how can I fix it?
View 8 RepliesHyundai :: Jerks And Turns Off While On The Move
I own a Hyundai hatchback which i converted to a LPG sequential kit 6 months back. The car was running fine till a couple of weeks back. Now I experience jerking at 2nd and 3rd gear and sometimes the engine just turns off while on the move at these lower gears or if the car encounters a pothole(I then have to restart the engine ).
So far, I've changed the ignition coil(6 months back) and spark plugs(1 week back) but I still experience the problem.The Hyundai mechanic says that it could be a problem either with the wiring to the ECU( since soldering instead of couplers have been used) or with the injectors. He says the cord wires and ignition coils are just fine.
The Lovato authorized mechanic who fitted the LPG sequential kit says that it could be a problem with the spark plug cord wires or the ignition coil.
The reason I don't see a rationale with the Hyundai mechanic's argument is that the car has been running perfectly for 7 months. Initially , when the car was fitted with the LPG sequential kit, there was a slight jerking problem but was gone once I got the ignition coil replaced.
The reason I don't see a rationale with the LPG mechanic is that the ignition coil is just 6 months ( 4k kms ) old. I've been struggling with this problem for a while since each mechanic is giving his own version of the problem. I might be wrong in my rationale above.