Golf IV / Jetta IV :: 2001 1.8t Stopped Running - Check Engine Light Blinking Because Of Misfire
So last Thursday I started my car up in the blistering cold and it ran fine for about a minute and started to misfire so I shut it off. It hasn't ran since. When that happened the check engine light was blinking because of the misfire. I didn't have a code reader at the time to read it. now that I got a code reader the damn thing isn't throwing any codes. it spits and sputters sometimes. I've had no previous problems with the car. Thinking It might be a weak fuel pump or bad coils and in not sure how to test them.
View 1 RepliesPassat (B5) :: 2002 Running Rough And Yellow Engine Light Blinking Then Turned Off
Drove fairly fast (160km/hr or 100 miles/hr) then took an exit down a ramp and had to stop at a red light. Noticed all of a sudden that the engine was running bit rougher and then noticed the yellow engine light blinking. I know to turn off the engine immediately when this occurs but then all of a sudden engine light turned off and car was running smooth again.
Car has been reliable for 7 years - proper maintained, synthetic oil, 171000km, timing belt changed, burns very little oil, good torque. Should I have it checked by the dealer (fantastic fair vw dealer)?
Mazda :: Check Engine Light Blinking And Idling Rough Almost Cutting Out
Today I went to the gas station and after I gased up and turned the car on my car started idling rough, almost to the point of cutting out. I started out on the road and my check engine light started blinking. After some time it stopped and just stayed on. The whole front end shakes pretty bad when at idle. The car has trouble accelerating till roughly 35-40 mph then seems to ride ok. I'm not very car knowledgeable, but I do take care of my car. I know I need to replace some of my hoses and spark plugs soon, but am worried that it may be more serious.
What I would like to know is: 1. What could possibly cause these issues and 2.
2003 Mazda Protege
Mercury - Monterey :: Rough Ride / Check Engine Light Blinking
Our 05 mercury monterey is riding rough and the check engine light is blinking all of a sudden. Two days back while driving home it was raining and we accidentally drove through a puddle, did not notice due to night time. After that it suddenly the light started to blink and engine felt rough. Checked the code yesterday morning and it showed cylinder 3 misfiring, no other codes came up. No one was available to check it yesterday and today. Have not started it again. Anything can be done before taking to the mechanic? I believe the number 3 cylinder is at the back side and not accessible easily. What could have happened?
View 19 RepliesWindstar :: 2002 - Car Running With Blinking Check-engine Light / Code P0306
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
Honda - Accord :: Check Engine Light On - Engine Surging / Running Very Rough
My mechanic tells me I need the intake manifold gasket replaced (check engine light on, engine surging, running very rough). How much damage can I do to the car by doing this repair myself and screwing it up? I've done lots of repairs on my car before -- brake pads, rotors, replace oil pan. I also have a copy of the manufacturer's shop manual.
View 2 RepliesTouareg :: Running Rough At Idle Then Check Engine Light Comes On
Filled tank with 8 gallons of 91 octane to top off. One hour later noticed car running rough at idle then check engine light comes on. Could it be the coil pack? Car has been running very well until now, and this Gremlin appears. I don't think it's the gas.
2004 -V8 Treg
52,000 on the odometer
Golf/GTI VI :: Choking Whenever Hit 3000 Rpm - Check Engine Light Came On Blinking
This morning on my drive to work my car would choke whenever I hit 3000 rpm right when the car is sucking the most air from my intake, and especially on 3rd gear and up. After being on the road for quite some time my check engine light came on blinking but went away right after I stop pushing the car to 3000 rpm to switch gears.
The car is on APR Stage 1 with AEM Filter + Nuespeed Intake + BSH Inlet Pipe.
Recently added was a VW Diverter Valve D Version due to an oil leaking from my Old Diverter Valvue G version.
Golf IV / Jetta IV :: 2004 - Blinking Check Engine Light
2004 VW jetta 2.0 ... So my vehicle stalled on me i replaced the battery, the alt, and then when i started it after installing the new alternator it didn't sound right so i checked it out and saw a spark plug wire was in very bad condition and was causing a spark where the spark plug and the spark plug wire connect so i bought a new set of spark plug wires and swapped the old ones for the new ones. Now when i start my vehicle the check engine light is blinking and the car definitely does not sound right. i am positive i did everything correct when swapping the spark plug wires but i am lost as to what could be the issue.
View 1 RepliesGolf IV / Jetta IV :: Oil Level And Blinking Check Engine Light
I just bought a 2000 GTI with the 1.8 turbo. It was very affordable, but it had a few problems. On hard rides, the check engine light was blinking AND I think there was too much oil in the crankcase (I say "think" because the dipstick funnel is gone and I'm not sure how far down the dipstick should go -- new one is on order).
I got rid of the extra oil, and now if I keep the oil in the hatched area of the dipstick (with the dipstick pushed down as far as it goes), the check engine light will never blink even under hard driving. But with the oil that low, the oil light will flash and beep on hard turns. I was experimenting, adding a little oil at a time, and hoping to find the magical sweet spot where neither the check engine light nor the oil light would go off. Instead, tonight I found the opposite -- the sour spot where BOTH of them go off.
So now I'm thinking maybe I need to change to a thicker oil. This car has 124,000 miles on it and was recently refilled with 0w-40. On my last car (a 1994 Golf with the 2.0 liter and 140,000 miles), the oil light would beep on hot days. I solved that permanently by changing from 0w-40 to Mobil 1 15w-50.
Finally, I checked the codes and it said there was a misfire in #2 cylinder as well as general misfiring So I checked the plugs and discovered that the previous idiot had gapped the #2 plug at 1/8 inch! So I (the present idiot) regapped them all and the engine seems to run better, but maybe going for months with such a huge gap has already fried the #2 coil. Should I just replace it? (or all of them?)
Malibu :: Running Rough At Stop Lights - Check Engine Light Came On
I recently replaced the head gaskets in my 2003 Malibu. First time and all seems other than it runs rough at stop lights. The check engine came back on and so I had it read and there is an air flow issue. Is there anywhere that I can get a schematic for the vacum lines? I have all over and cannot seem to find a loose or broken one.
View 3 RepliesAvalon 2005-12 :: Misfire And Check Engine Light Came On - Car Is Running Little Rough
My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.
View 1 RepliesTouareg :: 2004 VW - Check Engine Light Is On / Running Rough At Low RPMs
I have a 2004 VW Touareg with 116K miles. Yesterday the check engine light came on and she is running very rough at low RPMs. The manual tells me that there is either a problem with the exahust manifold or an O2 sensor is bad. It feels as if she is struggling for air. When you start the vehicle the check engine light flashes then stays on in the cluster. What can I expect when I take it in to the dealership? Is there anything I can check before I take it in?
View 4 RepliesPassat (B5) :: 2003 - Check Engine Light Came On And Car Is Running Really Rough At Stops
I have an 03 Passat with about 70K miles on it. My daughter put rug in it this morning (about 7 gallons) and since then the check engine light came on and the car is running really rough at stops. While accelerating, it seems to be fine. It is also getting about 10 mpg less than normal. MIL codes: P0300, P0301, P0302, P0303, P0304, and P0171. He said the P03xx codes were related to misfirings on each cylinder. The P0171 is a bank 1 failure (?). What do those codes really mean and could they be related to bad gas? Sent her off in my TDI JSW so she's not out on the highway if the Passat decides it doesn't want to go anymore.
View 6 RepliesAccent MC (2006-11) :: 2007 Running Rough / Check Engine Light Came On
The check engine light came on after cleaning the engine and the engine runs rough. Where to look. 2007 Hyundai Accord.
View 5 RepliesElantra MD (2010-15) :: Running Rough / Check Engine Light Came On And Misfire Code
In the last month, my car has had an awful time starting on 2 different occasions. The first time it ran really rough for about 1 minute then was ok. The second time was the same but the engine light came on. Took it to an out of town dealer and he said it showed a misfire code but could never find anything else and all looked OK. Spark plugs?
View 4 RepliesNissan - Maxima :: 1998 - Check Engine Light Come On And Car Started Running Very Rough
1998 Nissan Maxima had a check engine light come on and started running very rough. I took it to get a code read and came up with P0320 and P0325. I'm not worried about the 0325 since that's a knock sensor. 0320 is a misfire on cylinder 2.
With the car idling, I pulled the power connector from coil pack 2 to see if it made a difference in the idle - nope. I did the same for the other cylinders, and each responded with a noticeable change in the idle, which was remedied when it was reconnected.
I moved the coil pack from #2 to #4 (swapping them) and the same problem existed - idle was rough and didn't make a difference when I pulled the power on 2, but it did on all other coil packs. So, it seems the coil pack ins't the problem since multiple packs don't seem to make 2 work, but they work on other 4 and 6.
I then pulled the spark plug from cylinder 2, it was very black and looked in bad shape. I replaced it. Still no love.
I then put a spare plug in the coil and was able to see spark as the engine ran, so it seems that the coil pack at 2 is getting juice.
So, I have gas (big odor when the car is running - seems super rich) I have spark. Still running very rough and the 0320 code remains.
Ignition - Kia - Rio - Sparkplugs :: Check Engine Light Came On And Car Started Running Real Rough
I have a 2008 Kia Rio, 4 Cyl 1.6L, and recently the check engine light came on and the car started running real rough after getting the timing belt replaced at firestone. I took it back to Firestone and they said that 2 of the cylinders where misfiring and i need to replace the ignition coils and the corresponding spark plugs, but that i also want to get a catalytic converter cleaning or flush or something like that because of the unburnt gas that was running into the converter. Is this true? They want to charge me another 100.00 for the cleaning on top of the 300.00 to replace the 2 ignition coils and spark plugs, should i get this done or can i clean it out myself?
View 6 RepliesFord F-150 - 1997-2003 :: 2002 - Running Rough And Check Engine Light On
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?