Elantra HD (2006-10) :: 2008 GLS Squeals On Cold Start
I have a 2008 Elantra GLS, about 110,000 miles. Just got a timing belt and water pump change about 3,000 miles ago. Over the course of the last six months or so, she's started squealing a bit on cold starts. Originally it was only for a few seconds or so about once a month. However, since I returned from a 1500 mile road trip, the squealing has started happening on every cold start. Turning the wheel full tilt to either side does not seem to have any bearing on the noise, only when I rev the engine gently up past 2500rpms. What this could be?
View 6 RepliesTouareg :: Loud Metallic Rattling Sound Under Moderate To Heavy Engine Load When Cold
Problem description: A loud metallic rattling sound from under the car under moderate to heavy engine load, only when engine/exhaust is/are cold. It is noticeable from within the cabin with the windows rolled up and the sunroof closed. Crack a window or the sunroof and it's pretty loud. The first time I heard I, I thought "this is not good".
This is not an octane ping or valve train noise. It sounds like a coffee can with marbles being shaken in concert which what might be the rapping of a V8 engine's exhaust. I had a Sunbeam Tiger that rapped in the upper rpm ranges and this reminded me of that but instead of rapping, it shakes a can with marbles.
There has been much discussion and speculation as to what causes this. It does seem to occur only with late - 04 and up V8 Touaregs with the "sport" exhaust that replaced the "std"(?) exhaust used on the majority of the 04s.
Observation: I looked very closely at the heat shields, looking for ways they could rattle. On the passenger side (LHD), the heat shield has three main sections:
- Front: around/near the secondary cat (tightly secured)
- Rear: around/near the rear differential (tightly secured)
- Middle: between the two mentioned above (loosely secured)
The three sections overlap a little where they meet. It was very easy to tap on the middle shield and make a loud metallic sound. I put my finger between the two shields (where they meet) to isolate the two metal pieces and tapped again, and the noise was gone.
Theory: The harmonic resonance of the exhaust under load vibrates the middle heat shield and it rattles against the front and/or rear shields. As the shields heat up, they flex enough to provide clearance between each other and the noise goes away. This may be unique to the "sport" exhaust if (and I am only speculating) the heat shields were changed (in design or fitment) when they changed the exhaust.
Experiment: I tried a very simple experiment. I slightly bent the edges of the middle shield (~1/2 inch) where it was coming in contact with the front and rear shields. The allowed me to tap rather hard on any of the shields without them rattling against each other.
Result: I make the tweaks to the shields Sunday night. When I drove to work this morning, I put the transmission in sport mode and ran WOT until it shifted. Normally, I would have heard the sound (very loudly) but it was gone. No metallic sound. Not completely convinced, I repeated the experiment on the way home and, again, the sound was gone.
Summary: It was cool out when I was going to, and from, work (64F) and this would normally be the perfect set up for making the sound. I think that tweaking the heat shield has solved the noise on my Touareg. I am tempted to go back under there and pop-rivet a little brace between the shields so that they cannot rattle against each other again. On the other hand, I may just leave it be and do the pop-rivets if the noise comes back.
Anyway, I was excited to find a potential solution for my Touareg and wanted to share it will you all. I will post back after a while and report how it goes in the long term. Lastly, I really liked being able to put the air suspension in xtra-offroad and get under the car (easily) without using a jack....
Golf IV / Jetta IV :: Belt Squealing On Cold Start Up
I have a mkiv and before I got to work in the morning, I warm up my car for about 10 min. When I start it up the belt squeals. I do believe that it only does it in the morning. Should I have it checked out? i put belt dressing on it last night but it squealed when i started it up this morning so I don't think that worked......
View 10 RepliesPassat (B6) :: Hesitation And Misfiring Only During Heavy Load
I have a 2008 Passat Komfort Wagon with the 2.0T. At 40,000 miles, yes it only has 40,000 miles, the thing started hesitating and misfiring on me only during heavy load. I ran the codes and it said #4 cylinder misfire. The check engine light was only on during the time it was misfiring and hesitating. Took it to the VW dealer to have them run it again and get guidance and they verified the #4. When I picked up the car the CEL was illuminated. They said it does it when it misfires. I explained that it was not on when I dropped it off and they basically said tough cookies. So I replaced the #4 coil pack and all 4 plugs. CEL light still on, but wasn't misfiring. Next day it began misfiring again under heavy load. Took to Autozone to run the codes and now says misfiring on all cylinders.
View 6 RepliesFord F-150 (2004-2008) :: New Exhaust / Sound Under Load And At Cold Start
So I finally went and put the exhaust I had been wanting on my truck. Pretty simple set-up. I had the factory muffler cut off and a flowmaster 40 series on it previously. I liked the sound under load and at cold start but normal driving I could not tell a difference from a factory muffler. So I had the flowmaster removed. I still have 4 cats so it's not crazy but it is loud. The only time I have cackle is on initial start-up not even at WOT which was a pleasant surprise. I just like the look of a single exhaust but still want some sound. I have been gone awhile as I needed a little break from starting and also being drawn in to arguments.
View 7 RepliesSanta Fe (CM - 2007-12) :: Vibration As Engine Is Under Heavy Load When AC Or Air On
Question about my 2012 Hyundai Santa Fe SE. The car has 25,000 miles on it, and just recently like in the last 1,000 miles I have notice when I use the AC, or even the air without the AC the engine reacts very poorly like it is under extremely heavy load. The car shakes and vibrates.
I completely understand that in AC mode, the compressor kicks in, but this to me seems excessive. The car vibrates and the idle drops substantially. AC on is worse that no AC.
In addition, idle or under 35 is worse that HWY driving. The vibration is so pronounced that I sometimes wont turn the AC or air on as the vehicle feels like it is going to rip itself apart.
This is something new and never vibrated this much before the 25,000 miles. Anything I should look into or have the Hyundai Dealer look into? What I may be over looking? Would more stout battery work?
Prius (2004-09) :: Engine Knocks In Summer Under Heavy Load
I am the original owner of a 2006 Prius with 265k miles. I use Mobil 5-30 synthetic oil and I drive a steep hill every day and the engine knocks in the summer afternoons when I use cheap 87 Octane gasoline from Safeway or Costco. If I use better 87 octane gasoline (Chevron, Shell) generally there is less knocking. Also during the winter months no knocking even with cheap gasoline.
During summer I can sometimes make the knocking go away by accelerating or decelerating. The knocking is intermittent and generally occurs only during the steepest parts of the commute. The engine might knock for 30 seconds to 60 seconds before its goes away as I try to change the engine RPM.
Unfortunately I am burning some oil at a rate of approximately half a quart every 5k miles. Generally I watch the oil level, but there have been cases where the oil level has fallen below the lowest mark on the dip stick so I suspect I have some carbon build up.
I've read posts where others have used additives like gumout regane and I've read posts that say not to use additives.
Ford 6.0L Power Stroke Diesel :: Whistle Under Heavy Load
I posted earlier about a whistle that appeared when I was towing my old travel trailer (6000 pounds). It only happened a couple of times, and I had a hard time replicating it, so I elected not to waste any money with the deductable, and possible additional costs for a non-covered issue at the stealership.
Now, I am towing a larger 5th wheel trailer (11000 pounds), and am experiencing this whistle on every steep grade, while towing. Below are a couple of things I noticed, that had to be, before I would get the whistle:
* It only seems to happen while the cooling fan is engaged, and also only when the rpms reached 2800 and above.
*If the fan was on, but the rpms were turning below 2800 rpms, then it would not whistle. It would, however, after the transmission downshifts, bringing the rpms back up, while climbing.
*If the engine was spinning at 2800 rpms, and the engine fan was not engaged, then it would not whistle, until the fan would kick in.
* It only seems to occur when I am climbing a steep grade, on a warm day. Although, I haven't experimented on steep grades on a cold day...
It sounds to me like there is an issue with the engine fan system, but I thought I would put it out there, just in case any of the diesel guru's out there might know of something else that would cause a whistle like this, i.e., turbo?
Oh by the way, I also think that I have a performance reduction lately. However, I can't know for sure, as I have never towed this much weight with my truck before. I just kind of expected that I would be able to pull to the top of these grades, with a little extra peddle to spare. I have to floor it, just to "try" and keep up with traffic. And I haven't calculated my fuel mileage while towing this beast yet, but WOW, that fuel gauge needle sure does drop like a rock!
Ford Transmission :: Pulled Heavy Load Now Trans Oil Dripping?
I have a 1991 300 6 with an e40d trannsmission, our 4610 Ford tractor broke down in the field so i pulled it maybe 50 yds with my truck, it didnt like it but it did it. Now my tranny is dripping at a decent pace it looks like from the hole in the bottom of the trans, drove it ten miles home and it shifts fine. What could i have done??
View 4 RepliesSilverado :: P0307 - Check Engine Light Comes On When Going Up Hills / Under Heavy Load
I have a 2001 chevy silverado 3500 6L gasoline engine.
I have been getting a P0307 random multiple misfire #7 on and off for a few months now, occasionally the P0300. Check engine light comes on when I am going up hills, often under heavy load and sometimes when the truck is cold in the morning and the truck starts to run rough until the code clears, which it does pretty quickly usually. I have replaced coil, crank sensor, cam sensor, fuel injectors. If I unplug the battery overnight the code will be cleared and the truck will be running just fine the next day.
Ford 6.0L Power Stroke Diesel :: 2003 - Misfire Under Heavy Load?
I have a 2003 f 350 6.0, when under a heavy laod such as towing a 3000-pound trailer up a long hill at approx 60mph and 2000 rpm it intermittently mis fires.The boost gauge bounces up and down and i here a poping sound from the engine compartment.I have had it to several dealer and independent shops but with out the trailer or a heavy load it runs perfectly.They have told me fuel pressure is good and changed all fuel filters with OEM parts.
View 3 RepliesYaris/Scion & Vitz :: New Fan Belt Squealing During Cold Start
I installed a new Goodyear alternator belt on our 07 Yaris couple months back and it started squealing after the first day and only during a cold start. My past experience has taught me that it's normally due to a loose belt (when belt is new) so I tightened it just a bit. After 3 days it started squealing again. I've increased the tension on the belt three times now and the squealing has not gone away. It's only on cold starts and only for about 1 minute. If memory serves me right there is no tensioner for the alternator belt. It would appear that it doesn't matter how tight the belt is, it still squeals on cold starts.
View 4 RepliesAccord :: 93 LX - Belt In Engine Squealed Every Time On Cold Start
I have a belt in my engine that squealed every time I started the engine cold or got water on the engine (rain etc).
The belt itself has no cracks or fraying. I loosened the adjustment bolt on the alternator which raised the alternate up slightly and tightened the belt.
The squeal is completely gone even when starting from cold now.
Should I just conclude the belt was loose, or is there a precaution I should take?
Camry :: 2005 - Short Belt Squeak During Cold Start Up Only
I took my wife's 05 Solara to the dealer for the pully recall recently and had the serpentine belts replaced while they had them off. Now there is a short belt squeak during cold start up only. I called the dealer and they said to bring it back which I plan to do asap. 2005 3.3 V-6 Solara ....
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Loss Of Coolant When Pulled Heavy Load
Loss of coolant! I have a 2003 6.0 diesel with 200,000 miles. I put in a new oil cooler and ipr egr delete two years ago also flush the system and added a coolant filter. I filed it back up with the red antifreeze. Now the problem I have never lost any coolant since then and my deltas are about 5 degrees. But the other day I pulled a heavy load the first one since I did the repairs (coolant got up to 220 degrees and would drop back down) when I got home the coolant tank was about a inch low. I let the truck sit about 3 hours and checked it again and it was back at the full mark. Drove it the next day and it's back low about a inch, Any clue what's going on.
View 3 RepliesCorolla :: 2005 - Serpentine Belt Making Noise At Cold Start
I was wondering because serpentine belt is a big thing for 05 corolla since everything runs on it. I also had a 94 camry which had a alternator connected to a belt. and if i wanted to tighten up that belt i would just loosen the alternator and pull it. Is there a way to tighten up serpentine belt in my 05 corolla in the same way?.
View 1 RepliesAccent LC (2000-05) :: No Power Steering - Belt Screech During Cold Start
Awful belt noise that erupts during cold starts. I realize that this usually means a replaced belt. I want to know how to go along diagnosing which belt and then how to replace it. Here's the symptoms:
1. Awful belt screech when turned on, goes away within 20 seconds
2. Belt noise comes back when turning the wheel to back out of a right driveway
3. The STEERING WHEEL feels like it has no power steering WHILE the screeching is happening.
4. The headlights (when on) dim for about 3 seconds
5. All these symptoms happen when the temperature is below freezing and it's a cold start.
How is the belt screeching connected to the steering wheel being tough I turn?
Ford Super Duty (1999-2016) :: Trans Fluid Leak After Pulling Heavy Load
I have a 2000 SD F250, gasser, auto. Last week I pulled a heavy load and developed a tranny fluid leak. The fluid appears to be coming from what looks like a freeze plug on the bottom of the casing forward of the (torque converter?) pan . Is that plug easily replaced by a DYIer. Small leak. 150K on the motor. First time it has leaked. Heaviest load I've pulled.
View 2 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Misfiring Under Heavy Load Or High RPMs
So basically I thought it would be a great idea to degrease my motor from the top down.... After washing I start it up and drive down the road to head abunch of misfiring under heavy load or high rpm's.
My problem is that the misfiring won't throw a code. I then proceeded to buy a new ignition coil (thinking this was the problem) but with no code to go off which cylinder was bad I just switched the good ignition coil into each cylinder and starting it.
Up each time. None of them seemed to make it better. Also the injectors all seemed to be good. So what to do ?
2002 Ford F-250 5.4l