Ford F-150 (2009-2014) :: Fuel Injector Cleaner?

So whats everyones favorite? Reason? Its been a while since I had to buy any for a gas engine.

View 14 Replies

Lexus LS 2007+ :: Fuel Injector Cleaner Pushed More Power Than Usual

I was out driving my brothers Escalade today and notice that it had a lot more power than the last time I'd driven it. When I asked him about it, he said that he poured a bottle of fuel injector cleaner in about 2 weeks ago but hadn't noticed any difference. We thought maybe it was because he drove it all the time. He let his wife drive it and she noticed the difference as well.

View 14 Replies

Ford Fuel System :: 1991 F150 XLT - Low Idle With AC On

1991 F150XLT, 5.0, E4OD....Should the EFI system bump up the idle speed when the AC system is operating to compensate for the compressor load? Obviously I'm asking because mine sure doesn't. With AC on, the idle speed will drop to around 300rpm in Drive, like when sitting at a red light for example. Surely this isn't normal operation...is it?

View 4 Replies

Ford Fuel System :: Flat Spot When Accelerating Off Idle

I have a 4160 on a 351 Ford. I confess, it's a boat!

I had a major flat spot when accelerating off idle. I found it wasn't pumping on the accelerator circuit.

I replaced the accelerator diaphragm and cleaned the squirts and the passages. It squirts great now, but if I floor it, it completely bogs. If I baby it really carefully, once the engine gets over about 1800 rpms, it acts fine.

I thought it over, checked the travel on the arm that presses the diaphragm, and figured my pump cam was worn. It "seemed" like the duration of the squirt was not long enough.

I got a new cam kit. The orange cam on my carb was not a bit worn compared to the cam in the kit. Not encouraging. I put the only other cam in the kit that I thought might work. It was blue, and it gave more lift but no greater duration. It did not make any difference that I can tell. Is there a transition circuit I might have problem with? I don't know enough to go any further.

View 9 Replies

Ford Fuel System :: 1963 - 2100 Carburetor Won't Idle?

I rebuilt a 1963 ford 2B crburetor with manual choke. Put the carburetor on and it runs very rough. Won't go below 800 rpm or it dies and I need to choke it to start. Thought it was a vacumn leak so sprayed WD -40 and no change in idle. So pulled off the carburetor and put on the previous carburetor (with electric choke) and it runs great. I want to use the manual choke to hook up the cable though. I replaced everything in the carb. What do you think it is?

View 5 Replies

Ford Fuel System :: 1990 F150 Won't Idle Without A Little Throttle

I picked up a 90 f150 with the 302. it wont idle without a little throttle, so after a quick look under the hood i noticed alot of broken torn and missing vacuum lines. Where I can get some sort of diagram for routing?

View 1 Replies

Santa Fe (CM - 2007-12) :: 2008 - CEL On / Fuel Trim System Lean At Idle

I just got this 2008 santa fe a month ago from the dealer with 80.000 miles , and then yesterday the check engine light came on, i took it to auto zone and the put the computer and this 2 codes came up:

P2187
Fuel trim system lean at idle
explanation
the average long term fuel trim values at idle are more than 30% for 10 seconds

probable cause
- low fuel presure
- failed MAF sensor
- large vacuum leak
- cylinder misfire due to ignition system failure

P2189
System too lean at idle bank 2
explanation
failed MAF

probable cause
- low fuel presure
- vacuum leak on engine
- failed HO2S ( heated oxygen sensor-bank2 )

View 9 Replies

Ford Fuel System :: 1984 F150 - Truck Absolutely Will Not Idle

I have a 1984 Ford F-150 with an I6 engine and a motorcraft carburetor. The truck absolutely will not idle. So I got to looking at the carburetor, and found this red hose going from the carb to a metal pipe, the pipe was just dangling there not connected to anything, and the end it rusted off. I'm pretty sure I know where the other end is supposed to go to, I just don't know how to get there as obviously I am missing some parts and I can't find them so they must have been lost on the road somewhere.

Here's how it looks:

The end of the pipe:

Where it is supposed to end (I think)???

View 1 Replies

Ford Fuel System :: 1988 F250 / EFI - Slow Return To Idle?

Its an 88 F-250 4x4 with a 302 EFI 5-speed. Fair compression, runs smooth. When I press the gas pedal it takes about 5 seconds for the old girl to return to idle. I know nothing about EFI. My buddy,s out of town with the hand held mechanic. Is there anything I could check till he gets back.

View 6 Replies

Ford Fuel System :: Truck Won't Idle And Wants To Die / Bog Down When Accelerating Up Past 1200 RPM

Engine is a late 60's 390 with a C6 auto in good shape with a purported rebuild of about 10-15K miles on it. I picked up a nice condition Autolite 4100 and rebuilt it. Original tag states "C5AF AV" and below that in smaller font: "A 5AC" The base is stamped 1.12. It has the auto choke and auto tranny kickdown.

Truck has been sitting for 4 years so I drained the gas, primed the oil and added 5 fresh gallons. Started up on the second try!! But it won't idle and wants to die unless I feather the gas until it warms up. Also has a bog when accelerating up past 1200 RPM. I've been checking for vacuum leaks but none so far found.

I have a number of questions. But one of the areas I believe I need to correctly adjust is the float level, and here is where I can't get a clear answer or clear explanation of the correct procedures. What is the correct float level? My Sorensen rebuild kit actually had multiple values and the one that looked best had different primary and secondary values. I tried setting it "dry" by the upside down check with the cardboard supplied gauge. Good news is that it is not overflowing so needles and floats seem to be working correctly.

However, how do you do a more accurate wet setting? Appears to be two methods - one is the float setting and the other is the fuel depth. One good thread seems to state that both wet floats should be at 11/16". An engine builder locally said they should both be about level/parallel. Autozone says the primary should be 20/32" and the secondary should be 1 1/16". My rear wet float is almost level and it measures about 15/32". NONE of the data I've been able to find agree on the right setting nor do they explain in detail the correct way to measure using the wet float method.

I've got more questions like the choke settings and the vacuum port for hot air intake (currently open) and only getting 14 inches vacuum (I believe it should be 18 inches) etc., but I'd like to get the floats right before tackling them.

View 12 Replies

Ford Fuel System :: 1978 F150 - Idle Drop Down And Stall

I have an ambient temp switch connected to the vac port on my throttle emissions control solenoid for my 2150 carburetor. It's a 78 F-150 with a 5.0L 302, automatic 2WD. Would a bad ambient temp switch screw up my idle? I've disconnected the vac hose and it won't idle at all, and it does the same thing when I disconnect the two wires from the ambient temp switch. If I leave everything alone, I can get the idle down to around 1800rpm, but any lower than that and it stalls.

Is it possible to swap out this throttle emissions control solenoid with another type? I've looked everywhere and can't find an exact replacement, and I have no instructions on how to tune it.

View 4 Replies

Golf IV / Jetta IV :: CEL, TC Light Never Went Off / Sprayed MAF Cleaner On Sensor

.About a week ago NC got some really bad rain and in about 5 minutes the roads were under water. I had to end up driving through about a foot of water to get home, then parked the car. On my way home from work the next morning my car barely made it home, would cut out over 2k rpms and die if i didn't push the clutch in.

I sprayed some MAF cleaner on the sensor and tried that, it now will not idle when slowing down and will shut off every-time while rolling. (Also, while it is running it idles HORRIBLY and doesn't seem like it wants to pull boost efficiently)

I unplugged the maf and it does run a little better but when i pull the full 21lbs of boost then let off of the gas it dies.

Also i scanned the CEL and it says something about the MAF, i cleared it but the TC light never went off. and the CEL came back on in minutes.

View 3 Replies

Ford Fuel System :: Location Of Check Valve That Maintains Fuel Pressure On The System?

I have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?

I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.

My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.

So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?

BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).

View 8 Replies

Ford Fuel System :: 1988 - Got Code 41 - Lean Miss At Idle - ECM Or Injectors?

1988 F250 351 5.8

I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.

The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?

View 9 Replies

Ford Fuel System :: Truck Vibrate At Idle But Not Very Noticeable Seems Like A Regular V8 Rumble

I have an 07 F150 with the 4.6L engine and i was wondering if theres any need to clean my injectors at 30,000km the truck seems to vibrate at idle but not very noticeable seems like a regular v8 rumble but two ppl have pointed it out recently and have riden in my truck a bunch, should i be puttin some injector cleaner in my fuel?

View 3 Replies

Ford Fuel System :: Holley 4150 Choke - High Idle After Restarting?

I bought a new Holley 600 CFM 4150 with electric choke for my 79 ford F 250 with 400 engine. If I start the truck cold the choke works as it should and after driving 10 or so minutes it runs fine off choke. When I restart the truck after stopping for gas or food it goes back on high idle even with the engine temp at 180 degrees. Should it go on high idle even on a hot day fully warmed up every time i start it? I don't remember my last 600 doing it.

View 3 Replies

Ford Fuel System :: 1993 - Idle Erratically - Miss And Surge And Basically Tries To Die

1993 f-150 with 1988 5.0 with no pollution stuff fuel injected. here's the problem. Starts fine and idles great for about 5 minutes , check engine light comes on and it very nearly stalls at which point it begins to miss and surge and basically tries to die.

If I feather the Throttle i can keep it running but not smooth!! Can't find and vacuum leaks and the egr seems to be working (push plunger up - trk). dies. Ran fine when I bought it this way about 1 year ago and all of a sudden this. note.... It started doing this after it ran low on coolant but did not over-heat.

View 1 Replies

Ford Fuel System :: 1998 - Extreme High Initial Idle At Start Up

I have an issue with extreme high initial idle at start up. I took my 1998 Ranger with a 3.0L to the local dealer to have some work done about a month ago. Long story short, my number six plug wire got burned against the exhaust rail.

Anyway, I guess they re-flashed the computer to the newest *.bin, or flash version. After that when I start the truck the tachometer jumps up to 2200 - 2300 RPM and then it settles down to about 1500 after a moment or two, then it finally adjusts itself to about 1100 for a few more seconds and eventually ends up at 900 - 1000 RPM.

I confronted Ford about this and they said that Ranger's and F-150's do have a tendency to do that at start up. Ordinarily I wouldn't be too concerned, however I believe that the 2200 - 2300 RPM high idle at start up at 0 F, a bit much.

View 2 Replies

Golf V R32 :: 2008 - Vacuum Cleaner Sound Coming From The Engine At Start Up

I recently started to notice what sounds like a vacuum cleaner coming from the engine at start up, usually in the morning. The sound continues for about a minute or less then goes away. Haven't noticed it after repeated starts during the course of the day. Car runs fine, no CEL's.

View 4 Replies