Prius (2010-12) :: Installed LED Blinkers But Blinking Fast?
I just bought some LED blinkers for my tail lights and after I installed them, I'm getting a fast blinker thing like my lights are out. I know that LEDs don't draw as much power but is there anyway to fix this? Also, if I buy the Valenti tail lights that are LEDS, will I have that issue with them?
View 13 RepliesGTI 337/20th Anniversary :: Downpipe Installed / Car Started Rattle
I just installed a brand new 42DD downpipe in my car about two weeks back. About a week later, I started noticing a rattle that I hadn't heard before, coming from the undercarriage, about mid way back, where I assumed the downpipe is. I only hear the rattle at low RPMs, like 1000-1500 revs, when I pull away from a light. I can stop the rattle by giving it more gas before letting the clutch all the way out, but if it's something I can easily fix myself, I'd rather just do it.
I searched some DIYs and found this. [URL]..................................... I bought new sets of stage 1 dogbone mounts that I need to put in soon, probably next week when I'm on break, if that will remedy it.
GTI 337/20th Anniversary :: Fuse For Blinkers Keeps Blowing
My fuse keeps blowing for my blinkers i legit changed it probably five times and it blows after i use them once. What good the problem be?
View 4 RepliesGTI 337/20th Anniversary :: Brake Light On Dash Blink And Beep After Every Stop
What makes the brake light on the dash blink and beep after every stop? I've checked my e brake and made sure it was off so I know that cant be the issue
View 2 RepliesGTI 337/20th Anniversary :: 2002 - Installed 3 Inch Down Pipe Now CEL Came On?
I have a 20th anniversary gti and recently installed my 3 inch down pipe.. but after i got it installed my check engine light comes on. the code says its an 02 sensor. i got that o2 sensor spacer from ecs tuning.. but the light keeps on coming on.. what should i do? this light bugs me so much....
View 10 RepliesGTI 337/20th Anniversary :: Installed HIDs, No Longer Have High Beams
Ok so I installed HIDs in my stock housing, I no longer have high beams since I bought the low beam ones only and I think since there is nothing running to where the high beam wire on the oem harness my high beam light on the cluster is stuck on no matter if its on low beams or high beams and its causing my Fogs to not work.
View 7 RepliesGTI 337/20th Anniversary :: Installed Downpipe - Smoke Coming From Turbo
i just installed my downpipe and i took it around the block and i opened the hood and there was smoke coming from the turbo could it be b.c i didnt put the washers witht he bolts to connect the dp but i put them on really tight or could it be the wd40 i sprayed on to loosen the bolts?
View 7 RepliesGTI 337/20th Anniversary :: Installed FMIC Now Temp / MPG Gauge Reset?
I just installed a eurojet race FMIC (bumper fitting was horrible but thats another story) and now my outside temperature and mpg readings are all off on the cluster computer. The temperature actually just rises when i start driving and the mpg doesnt change at all? Should I just disconnect the battery so it resets? ]
View 1 RepliesGTI 337/20th Anniversary :: CEL On And Car Starts Pulling Back When Accelerate Fast
I just recently put in an APR chip on my o4 gli from one of their dealers, a day or two later I noticed when I try to accelerate fast my check engine light comes on and the car starts pulling back. That was almost a week ago, today I went back to the same place to get a short shifter, I told them the problem while I was there and they said it was my coil packages. I replaced all 4 and im still having the same problem...
View 2 RepliesPassat (B5) :: Blinkers Blink Once Or Twice Then Stop
They blink once or twice then stop. What needs to be done and is it a job a backyard mechanic can easily handle?
View 10 RepliesPontiac :: 1966 - Lights Malfunction / Blinkers Don't Blink
the blinkers keep working and not working now they aren't of course.. but the left one only worked then something happened and the left only stayed on (not blinking) when the head lights were on. then it switched now they don't turn on at all. the fuses are good the relay is good all the wires are good I got new bulbs in as well and pointers. it's a Pontiac starchief 1966 and the flasher is good
View 1 RepliesFord Ranger / B-Series :: 1997 - Blinkers Are On And Light Up But Does Not Blink
1997 Ford Ranger Manual. The blinkers are on and light up they'd just don't blink . Don't know what to do all fuses seem to check out.
View 2 RepliesGTI 337/20th Anniversary :: Getting Too Many Error Codes?
Ok, It doesn't start, it tries to but doesn't get there, its not the battery the alternator, the starter or the battery terminals which goes to my second question...for error codes do I just pop them in google to see what they mean or is there a better site??....reason why I'm removing the lip its because its being towed to the mechanic, its at my job's parking lot right now, first time ever my VW leaves me stranded but I guess it happens:
Error codes I got:
p0261
p0267
p0270
p0264
p0445
p0037
p2257
p0010
p0414
p0141B
GTI 337/20th Anniversary :: Backfire - 11 Codes Appeared / ECU Is Going Out?
For about two months I've been having a backfire problem but only when I get on it. We checked for leaks and nothing . The car had 11 codes and were all short to ground. Mechanic is saying my ecu is going out and I need a new one. Is it possible?
View 8 RepliesGTI 337/20th Anniversary :: Receiving Awp Engine Codes During Ecu Swap
I am trying to swap my ecu for a chipped one out of an 04 gti 1.8. Both awp engine codes. I programmed the immobilized and the car doesn't start. I am thinking it has the ignition kill feature but the guy who sold it to me doesn't think it does. i was just wondering if the ecu's are compatible even though the part number is different.
View 8 RepliesGTI 337/20th Anniversary :: Cylinder Misfire Codes For OBDII?
I changed my sparkplugs and coil packs last month. Was getting CEL light but it would go away after a while. I figured out that I had gapped my spark plugs way to small (almost touching) so I took them out two nights ago and regapped/ reseated them.
My car was running fine yesterday, but today when I started my car up, the engine was shaking a lot for about 10 seconds and the CEL was blinking. After 10 seconds the shaking and CEL went away...
It drove fine. I'm just wondering what could be throwing these CEL's and causing the shaking? Plugs are gapped to 0.32
Also, I had my timing belt and water pump replaced almost two weeks ago now. Any chance that could be lending to the problem?
My guess is that one or more cylinders are screwy. I'd rather not bring it into the vw mechanic since I'm tight on cash.
GTI 337/20th Anniversary :: Over Boost Codes / Limp Mode
There ended up being 6 or 7 codes. Originally the first O2 sensor and wire seemed to go bad, I replaced them and it ran well for a couple days and then started running like ass again...Now there are a few codes, none for the 02 sensor, but for over boost issues...Does this mean my n75J valve is causing the problems? Is it possible that my software is just going bad? ...I bought the car somewhat molested and don't quite know the extent of the parts on it, nor the brands( specifically, the software...).
The current codes being thrown:
P0238 mani pres g31 sig to high
P0234 overboost
P0106mani barometric sensor g31
We replaced the manifold pressure sensor, and am not having the issues but they could and probably will come back after 50 or so miles...Previous code also was P1114 02 sensors and we replaced the front sensor. It may be that the software that is on the car is starting to go..
GTI 337/20th Anniversary :: AC Vents Has Started To Peel
The center AC vent has started to peel. Any tricks to repainting it or good place to get the part to replace it? Any good tips for it's removal before I just dive in?
View 15 RepliesGTI 337/20th Anniversary :: After Installation Of Intake Getting Codes 16485 / P0101
I am having an issue after my intake install, it was working fine all day and last night i get a light on the dash bored (looks like the one when you take off the esp) and I get this:
code 16485 Mass Air Flow Sensor (G70) Implausible Signal : P0101
Static - No
What could be the cause of this because i ran this intake before no issues I only took it off and put the stock intake back in due to the rain but now since the rain is gone i decided to switch