Ford Wiring/Electrical :: 2001 F250 - Auto To ZF6 Swap Cruise Not Working
I have a 2001 F250 with 7.3. We swapped the auto for a zf6 manual. We left the auto's shift position sensor tied to the frame and left in neutral. I did install a pcm from a manual transmission pickup. Also have the clutch position switch hooked up. I have an Edge Evolution CTS2 reprogrammer, and on the display the gear indication always shows P. I suspect that is why my cruise doesn't work. For interests sake, I tried manually adjusting the shift position sensor through all gears, and the reverse lights come on when in reverse but the Edge's display always shows P. My question is with a manual transmission, how does the pcm know that it is in gear? The only sensor that I am aware of is the reverse sensor on the zf6.
View 4 RepliesFord Wiring/Electrical :: 1973 F250 - 3G Alternator Swap / Adding Relays To Keep Headlights From Shutting Off
I'm working on the '73 F250 in my sig. I'm not very skilled when it comes to electrical work and I don't want to hack things. First up is I'm wiring a 7-way trailer connector with brakes. I need to tap into the brake light switch at the pedal, what is the cleanest way to do this? I was thinking of sticking a blade connector in the existing connector or adding a plug pigtail.
Also in the future I will (hopefully) be doing a 3G alternator swap and adding relays to keep my headlights from shutting off. I'm looking for suggestions on a junkyard or aftermarket fuse block that will accommodate the circuit breaker for the trailer brake, the 100 amp fuse for the 3g swap and the relays for the headlights.
Ford Wiring/Electrical :: 2008 F250 - Power Mirrors Not Working
I have a new to me 2008 F250 XLT. Neither side on the power mirrors is working. The manual shows fuse number twelve on the passenger side fuse block is the one that controls this circuit. The fuse is good (continuity wise). What I need to know is what color is the wire that feeds power to the switch block on the driver's side door panel. Pulled it out of the door panel and wiring was intact and corrosion free. I need to find out if there is power there or is it an issue between the fuse block and the switch.
View 2 RepliesFord Wiring/Electrical :: 2008 F250 - Side Mirror Will Not Fold
My 2008 F250's passenger side mirror will not fold/unfold with the switch. Also the motor continues to run when the switch is moved to fold/unfold the mirrors.
View 4 RepliesFord Wiring/Electrical :: 2004 F250 - Airbag Light Flashes And Stays On
I have a 2004 250 SD. Supercab. Took out the bench and replaced with captains or buckets, whatever you want to call them. Perfect fit. The new seats have their own seat belts built in to them. The old ones, were mounted to the floor and roof. Now the air bag light blinks for a fairly long time, then stays on! What? OK, So, what do I NOT know about this project? I did have to make the wires longer in order to reconnect the plugs. Not a problem, I am an electrician. Trouble shooting is ok, when you know where to start.
View 10 RepliesFord Wiring/Electrical :: 1997 F250 - Rear Tail Lights Wiring
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesFord Wiring/Electrical :: 1999 F250 - Door Courtesy Light Wiring Diagram
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 RepliesFord Wiring/Electrical :: 2004 F250 - Turn Signals And Hazards Stopped Working
So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 RepliesFord Wiring/Electrical :: 1990 F250 Hard To Start - Glow Plug Controller Relay Wiring
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 RepliesFord F-150 (2004-2008) :: Engine Swap From 2005 Model To 2010 F250 5.4?
Will an engine from a 2010 f250 5.4 work in my 2005 f150 5.4? f
View 7 RepliesFord Wiring/Electrical :: Wiring 2008 Seats In 2001 Model?
Let me start by saying electrical is something I really have no knowledge of....(never used any kind of an elec meter and don't have one) simple, Pos-grd and fuse, NP. I really don't want to fry something in these expensive new seats w/my normal trial and mostly ERROR!
The 08 (drivers) seat has 4 wires in the input clip.
GRN-RED (heavy gauge)
BLK-PURP (heavy gauge
BLU-RED
BLK-WHT
and my 01 whip out of the floor has a 3 wire setup.
GRN (heavy gauge)
BLK (heavy gauge)
BRN-BLU
I can wire PS side seat from fuse box and ground it NP. It only has a 2 wire set-up in the new seat.
Ford Wiring/Electrical :: 2004 - Instrument Cluster Wiring Diagram?
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 RepliesFord Wiring/Electrical :: 2004 - Installing Seat - Wiring And Functions?
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 RepliesFord F-150 (2004-2008) :: Steering Wheel Controls Wiring For Head Unit
Looking for the wiring diagram for the steering wheel controls for the head unit, mainly which wire is volume. I bought a new head unit for my 04 f150 truck and cant find the wiring diagram online to figure it out. I know there are 3 separate connections.
1 main one for power, gnd, ant, speakers, etc..
1 for the subwoofer if your truck came with it which mine did.
1 for the steering wheel controls if your truck came with it which mine did.
I want to know what the different color wires are connected to on the steering wheel control connection. i have had no luck searching online for about an hour. I know I could buy an adapter but really only want the volume to work and figured if I could just tap into that one wire and connect it to my new head unit.
Ford Wiring/Electrical :: 1983 F250 - No Spark At All
I have a friend of mine that has a 1983 and he had me change the water pump in it because it started leaking and it has been sitting for 7 Months now. I changed that but I can't get this bugger to start. I used to be a mechanic in a past life so I know what I'm doing most of the time so let me explain what has transpired here.
I attached my remote starter, turned on the key and cranked over the engine after shooting a little bit of starting fluid in the carb and she cranks over but won't start. I then pulled the #1 spark plug out and then did the same thing to check for spark and nada. I put my light tester on the coil and there was power. I have run into this kind of problem years ago with other vehicles so I thought I would just go ahead and replace the Coil and also the Control Module. After replacing these parts, still no spark. Since the distributor is there only to distribute the spark (meaning no electrical connections to it) I'm assuming that the Pick Up part that is down by the Crank shaft might be bad.
How to test either the Control Module or the pick up. I'm trying to diagnose this problem without needing to remove the module and taking them to the parts house for testing. (long drive). These wires should have 12 volts when the key is off and these wires should have 12 volts when the key is on.... and so on.
Honda - Accord :: 2007 - Electrical Arcing / Clicking Sound Coming From Steering Column
In the past few weeks I have noticed that as I turn the ignition of my 2007 Honda Accord, I hear a strange electrical arcing/clicking sound coming from the steering column. The car starts normally and the sound goes away once the engine has started. I have taken the car to my mechanic and had the ignition checked out and they could not find anything wrong. How to identify the source of this noise/fault?
View 4 RepliesFord Wiring/Electrical :: 1992 F250 - Blinkers Will Not Work
I recently bought a 92 F250 and love it but the blinkers will not work. I have replaced both flashers and the multifunction switch. (the wipers had issues too that were fixed by the switch...) Now what? Im at a loss..
View 7 RepliesFord Wiring/Electrical :: 2003 F250 - Flashers Won't Work
My work truck is an 03 F250 5.3L. My flashers recently stopped working. I turn them on, and they will work anywhere from 5 seconds to a few minutes, then either blink rapidly and shut off, stay solid for a few seconds and shut off, or just shut off. I push the switch off and on again, and the cycle repeats. All my other lights and turn signals work fine with no issues.
This wouldn't be a huge issue, but where I work I need the flashers a lot. The truck has a bar light and siren/pa system wired into it, but not to the lights or anywhere near that. I can't say exactly how it's wired because I didn't install it, but I followed the wires and they don't go under the steering wheel where I would assume the relay and wires for flashers would be.
What sounds like is wrong? I wouldn't think it would be the relay because then I would think that I would be having problems with more than just the flashers. So I'm not sure if there would just be a ground issue or if it's the actual switch that turns on the hazards. Also, there are no lights that are burnt out.
Ford Wiring/Electrical :: 1979 F250 Starter Keeps Running
I have a 1979 f-250 4x4 with a 351m. The problem I am having is my starter keeps running after the truck starts and also after I shut off the key. I didn't get the battery unhooked in time today and it completely melted the lug off on the solenoid, but the other wires were barley warm. What could be causing this problem? The battery is new, the cables are new and the Sol. was new. Maybe the switch or the starter?
View 8 Replies