Ford Wiring/Electrical :: 1984 F150 4x4 - Died While Driving - No Spark?
My '84 F150 4X4 inline 6 Died last night while driving. just conked out and died right there on the spot. no sputter... no gasping... just instant death...
after some investigation i found i wasn't getting spark anywhere. not at the plugs, not at coil. I have replaced the ignition module to no avail. still no spark I am going to swap in a the coil tonight. sure do hope this works.
Ford Wiring/Electrical :: 1984 - Clicking Sound Under Dash?
I have a '84 Bronco and before I redid all the ignition wiring when I turned off the key the engine would stay running for about 6 seconds and then turn off. Now when I turn off the key and turn off a switch about 6-8 seconds later I here a click sound that comes from under and about center of the dash. And sometimes it clicks on and off in rapid secession kind of like when you flip a light switch on and off quickly. Some days it does it and some days it don't.
If I leave the battery hooked up then it drains the battery overnight or within a day, and sometimes its just fine. So to be safe I unhook the battery whenever its not being driven or started periodically. I am wondering what is in the center of the dash that needs power and that controls the ignition stuff?
Ford Wiring/Electrical :: 1984 F250 - Indicator And Warning Lights Are All Out
My indicator lights are all out. The turn signals work correctly, as do the dash lights themselves, but all of the warning lights are out. The truck sat for three years and I have just gotten it back on the road.
View 7 RepliesFord Wiring/Electrical :: No Spark When Cranking Until Key Let Off?
I have a 1988 Bronco II 2.9 5 speed 4x4. Ive had it for about 2 years and the other day I put on a new cap and rotor and plug wires. I also cleaned the IAC. After that it ran fine for about a day and then I made a 2 hr trip and cut it off at a store. When i tried to recrank it, it just turned over and over and over for about 10 minutes and then it finally just cranked and ran like nothing was wrong. Its done the same thing twice since then (past 3 days) .
Yesterday when it did it, I pulled the coil wire and put a "spark tester" plug in the wire and tried cranking it. It only sparks right at the end when u quit cranking, itll spark 1 maybe 2 times. It'll crank if you just do a few short bursts of turning the ignition key to on. What else to check, or what the problem probably is? At first i was thinking it was the coil or module, but its only when cranking so maybe an ignition key problem or relay between there?
Ford Wiring/Electrical :: Cranks But No Spark If Voltage Is Down Around 12v
So I've been having problems with my old duraspark 2 ignition box and I replaced that but it didn’t seem to fix the problem. The truck doesn’t start if the voltage is down around 12v, it cranks but no spark. So I put it on the charger a couple hours ago and came inside and was reading old posts on here about testing the ignition system and then just went out to test the negative side of the coil with a test light and low and behold when my assistant went to crank it over the truck started right up like everything was fine. I took off the charger.
So then what I did was I checked the charge at the battery while the truck was running with a dvm and the voltage was 14.33 then I turned on the electric fan and it jumped up to 14.88 and spiked at 15 then held at 14.88. is that normal or is the voltage a little on the high side? If it is high then could it be the voltage regulator or alternator? And could that have been my problem all along instead of the ignition module?
Ford Wiring/Electrical :: 1983 F250 - No Spark At All
I have a friend of mine that has a 1983 and he had me change the water pump in it because it started leaking and it has been sitting for 7 Months now. I changed that but I can't get this bugger to start. I used to be a mechanic in a past life so I know what I'm doing most of the time so let me explain what has transpired here.
I attached my remote starter, turned on the key and cranked over the engine after shooting a little bit of starting fluid in the carb and she cranks over but won't start. I then pulled the #1 spark plug out and then did the same thing to check for spark and nada. I put my light tester on the coil and there was power. I have run into this kind of problem years ago with other vehicles so I thought I would just go ahead and replace the Coil and also the Control Module. After replacing these parts, still no spark. Since the distributor is there only to distribute the spark (meaning no electrical connections to it) I'm assuming that the Pick Up part that is down by the Crank shaft might be bad.
How to test either the Control Module or the pick up. I'm trying to diagnose this problem without needing to remove the module and taking them to the parts house for testing. (long drive). These wires should have 12 volts when the key is off and these wires should have 12 volts when the key is on.... and so on.
Ford Wiring/Electrical :: 1987 - Died While Driving - No Spark?
So I bought my 1987 F150 XLT 4X4 (4spd) about two weeks ago and haven't had any issues with it so far... until now. As soon as I got it I did a full tune up. Changed plugs, cap, rotor, fuel filter, new battery, sea foamed it, fuel filter, ran a bottle of fuel stabilizer through it, new pvc valve, cleaned the throttle body, oil change, etc., ( all the usual things).
Was running fine up until two days ago when I was driving down the highway doing about 90km/hr in 4th when the truck suddenly lost power, sputtered and died. Tried to start it again and it will turn over but not start. So I get a nice expensive tow home and start to diagnose the problem. It is not a fuel issue. I can hear the pumps coming on, and fuel is coming out of the fuel filter so I cross that off the list.
Next I check for spark. No spark at all. So I run some tests. Battery is putting out 12V, about 10 when cranking. The solenoid is getting power and putting out power. No visible damage to any of the wiring, and all the grounds look good.
Next I just went ahead and swapped out the coil thinking that could be the issue. Didn't work. So I preform some more tests on the old and new coils. Both are grounded and having voltage pass through them. Next I take the TFI module off the distributor and check for resistance. Everything still checks out fine. Now I am thinking that the only thing left could be the PIP in the distributor. So instead of taking the dist apart and screwing around I go ahead a get a brand new dist and throw it in.
Now I am stoked and thinking that I finally fixed my truck and go to start it up and.... no spark. It still turns over but no start. I am trying to provide every bit of detail that I can. When I say I tested all the components I mean I REALLY tested them. I did both tests from the Haynes manual and from various sources off this site.
I am almost at the point of getting it towed to the shop, which I really do not want to do. A day before this happened I degreased the engine and VERY carefully sprayed it off with water. In the process I am thinking I may have damaged something?
Ford Wiring/Electrical :: Crank But No Start / Not Getting Spark From Coil
1996 Ford F150 5.0 ... New battery, new alternator, new starter, new coil, dis cap good and rotor is good. New plugs and wires. Ignition mod tested good.
Drove a mile from my house and lost power to my engine. Lights and radio work. Just sits there and cranks and cranks. I'm not getting spark from the coil. Don't know a lot about engines.
Ford Wiring/Electrical :: 1986 F250 - No Spark From The Coil
I have an 86 f250 i just bought back with no spark. this truck is not original. used to be a diesel. has a 400 out of 81 f250. had this truck running just fine 4 years ago. sold it to a guy running and bought it back 4 yrs later not running.
Checked all the connection to make sure they r clean. Had the ignition modular tested and tested good. I have 12+ volts from the white and red wire. I have a little over 6 volts at the bat side of the coil. I have no spark from the coil. I notice every time I connect and disconnected the bat cable I will get a spark from the coil. i ran a test light from the tack test sight on the coil and tried to start and the light stayed real dim and never flickered.
Ford Wiring/Electrical :: Ignition System Keeps Shorting Out / Killing Spark
I have a 77 ford truck with a 351 ,the ignition system keeps shorting out, killing spark. If i replace the starter solenoid, it works for a while, then goes out again. I have replaced 4 solenoids this month. What could be shorting the solenoid out? Had the truck for 8 yrs. now, never had a problem with it till now. It has a mallory dist. it was in when i bought it.
View 7 RepliesFord Wiring/Electrical :: 1990 - Spark Plug Replaced Now Ticking Sound?
My truck is a 1990 F-150 with the 351. I was replacing the spark plugs last night, got it all wrapped up and everything squared away, and after firing the truck up I noticed a ticking noise. It was not there before I replaced the old plugs, and it is not at all loud. I can hardly hear it with the hood closed. It appears to be coming from the driver's side of the engine. It does not misfire when its idling, and it revs smoothly. However, while driving it is noticeably choppy and feels sluggish.
Any thoughts on what it could be? I used dielectric grease on the boots, but I did not replace the plug wires themselves, or the distributor cap. I am probably going to replace the plug wires today though, because the plugs I took out were not in good condition and its been a bit too long since I replaced them last. Its also worth noting this engine is less than years old. This is a frustrating problem because I've replaced the spark plugs on her before, so I'm not quite sure what I did wrong this time.
Ford Wiring/Electrical :: 2006 - Wipers Doesn't Shut Off?
I have a 06 f350. Out of the blue my wipers will not shut off without pulling the 30 amp fuse in engine compartment . Even with ignition off.
View 7 RepliesFord Wiring/Electrical :: 2005 Expedition Will Completely Shut Down While Driving
While driving along my Expedition will completely shut down, ignition, all accessories, everything, for a few seconds then come back alive. It happens generally up hills or around right turns.
It is like the main ground strap is loose and losing contact momentarily. I don't know where to look for this. Engine was replaced 1500 miles ago. Battery and all visible connections seem ok.
Ford Wiring/Electrical :: 1996 - Wire A/C Switches To Shut Off Compressor Relay
I'm planning the install of a 1996 351w into my '77 F-100. I'm using the '96 accessory serpentine drive (FS-10 A/C compressor, '96 alternator, etc.). It needs to mate up to the '77 wiring. I'm going to use stock '96 underhood A/C components (accumulator, hoses, condenser).
As best as I can tell, the '96 system uses the ECU to manage the A/C system, but I've converted the '96 motor to a carb.
Looking at both the '77 and '96 systems I think the easiest underhood wiring solution would be to use the '77 compressor ON wire as a relay trigger, and use the '96 High Pressure Cut Off (HCPO) on the compressor manifold, and compressor cycling switch attached to the accumulator to interrupt the relay output to the compressor.
I can get the switches and pigtails, and I can look up their pressure trigger points, but I don't know the voltage the '96 switches operate at (12v or some reduced voltage?) or how to simulate their trigger conditions to see how they work. I guess that at ambient pressure the HPCO should be normally on and the cycling switch should be normally off. So I could just wire them into the relay ground or trigger connection. But of course they aren't simple two wire switches. (Edit: Looking at it online, the cycling switch appears to be two wire, the HCPO is 4 wire).
How to wire them, should I use them to interrupt the relay ground or trigger connection?
Ford Wiring/Electrical :: 1996 F250 - Shut Off Suddenly For A Few Seconds When Driving On Expressway
I have a 1996 F250 460CI that was running great for years and all of a sudden it shut off for a few seconds when I was on the expressway. It was like turning the ignition key off and turning it back on. It did it several times and eventually just died and would not start. I put a new coil on and it worked fine for about 150 miles and now it started doing the same thing again. The check engine light was on for a few seconds but not all the time so I am not sure if diagnostic equipment will show any error messages. Mileage on my truck is 92k. Does this sound like a distributor pickup issue?
View 6 RepliesFord Wiring/Electrical :: 2004 F350 - How To Make Dome Light Not Have A Delay To Shut Off
My Viper 2 way alarm, instead of the brain being wired to each of the 4 doors individually. The installer ran 1 wire to the dome light. Seems to work fine as far as arming/disarming/locking/unlocking, but since the dome light stays on for 10 seconds or whatever after the door is shut, when i arm it.
The 2 way remote says "door open" because the light is still on so it thinks a door is open. this eventually times out and all the sensors arm, but there's a long delay. it arms fine and no alerts pop up if i lock the doors first from the outside keypad on the door, making the lights go off, then hit arm on the viper, and everything is good to go.
Can I change it so no matter what, as SOON as i shut the door, the light goes off? I want there to be NO delay, if possible. If not, I may need to just have the installer run a wire to each door and take the single run to the dome light off, as it is sorta annoying to me.
Ford Ranger / B-Series :: 1984 Has Spark / Cranks But Won't Start
working on a 84 ranger it did run fine for 3 wks then while driving there was a thump and it stopped and wouldn't start. Now working on it has spark cranks but won't start. while trying to start when I let off the key it tries to catch but only at that time not when the key is turn to start normal. we poured fuel into the carb and it still didn't start. Leaning toward compression maybe?
View 4 RepliesFord Ranger / B-Series :: 1984 2.8L Started Then Revved Up High And Shut Off Immediately
I just rebuilt the carb on the truck, it has the 2.8L, and when I went go go start it, it cranked for awhile until fuel filled the bowl, then it started and revved up high, I shut it off immediately and it turns out the throttle linkage was binding for some reason, I fixed that but now it wont restart.
I was cranking it for a while and gas started spewing out of the top, so I took the top of the carb off and reset the float height and now it doesn't spew gas.
I pulled the plugs and checked for spark and it's a really bright blue spark. I'm thinking it's just flooded, lots of gas on the plugs? I'm just waiting for it to clear out now and trying to brain storm what could be wrong.
Ford Wiring/Electrical :: 1967 F100 - Instrument Cluster Gauge Wiring
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....