Ford Transmission :: 1986 F150 V6 Not Shifting In Drive
1986 F150 3spd Auto 300 v6. My truck will not shift out of 1st in Drive, to shift into second I have to column shift to 2nd. 20mph top speed and idk what to do to fix it. I would like to put a 5 spd manual in it cause I would like to drive over 50mph.
View 4 RepliesFord Transmission :: 2000 F150 - Transmission Holding 2nd Gear Too Long Before Shifting Into 3rd
I have a 2000 F150 5.4L with 157k miles on it. I think it has the 4r70w trans. The transmission has started holding 2nd gear too long before shifting into third. Throttle position doesn't matter, it does it even under light throttle. I do not have a check engine light. I have owned the truck since new and the trans fluid has been changed 3 or 4 times. The fluid looks pretty good now, not burnt or anything. The truck has been sitting in the garage a lot over the past 2 years, I drive it at least once a month and have put maybe 2000 miles on it this year. It shifts fine through the other gears, just 2-3 has an issue. Truck has the towing package.
View 6 RepliesFord Transmission :: 1994 F150 Not Shifting Into 3rd Gear Or Above
My 94 F150 has been actingup lately with the 4r70 transmission not shifting into 3rd gear or above. I replaced the MLPS sensor and re pinned the plug as per the instructions with the switch.The old sensor had the plug on the side, same type of plug, but wires indifferent spots. Truck wouldn't start like that, so repinned to match the instructions. I couldn't get the neutral mark to 100% line up as there is not enough adjustment, but it is very close.
The old plug had
32-298-140-33
57-199-359-463
I switched it to
57-359-199-463
33-140-298-32
Then tried
463-359-199-57
33-140-298-32
Truck still won't shift to 3rd, overdrive off button doesn't light up and itwon't start in neutral. I tested the ground at the connector and it lights up atest light connected to the pos bat cable with no issues.
Back up lights won't work, but flicker as going from R to N, so I suspect that is due to the fact I couldn't get the marks to line up 100%, but i'm not worried about that now.
Ford Transmission :: 1996 F150 Not Shifting Into Second Under Full Throttle
96 F150 carbed 300 with a C6/208 SAS44/9" with 3.55 on 35s.
I put a transgo shift kit in the transmission before putting it in the truck, it also has a small stall. At half throttle you can manually shift 1-2-3 with no issue at all. Under full throttle when you shift to second it won't go into second until you push the shifter into third. Then it'll go to second and spin the tires when it grabs second in dirt. This is all in 4lo, I was gonna switch to 2hi and try it but it's raining and I don't feel like crawling under it to change it. The truck is a mud toy so will spend 90% of its time in 4lo.
I don't have a vacuum line currently hooked to the transmission because I have the same shiftkit (transgo) in my 77 and no vacuum line on it either and it works fine.
Chevrolet - 1500 :: Transmission Does Not Engage In Drive
Overhaul trans, new old pump, but doesn't engage in drive. Reverse and all three low work fine. Drive will only work when rpm's are applied. But without any power.
View 4 RepliesFord Transmission :: 1997 F150 4x4 V8 Skidding / Clutch Is Not Holding At Times When Shifting Up Or Down While On Cruise And Slight Hills
This is an Auto/4z4/4.6 V-8. It's Skidding or a Clutch is not holding at times when shifting up or down while on Cruise and slight hills.
someone suggested changing oil and filter about two years ago. I did that and it didn't change a thing. $145 that time.
I'd like to know if its the clutch in the torque converter, or the Transmission? If I have to change something out, should I get both?
Ford Transmission :: 1997 F150 - Front Drive Shaft Installation - Bolt Size?
Bought a used 1997 Lariat Supercab 5.4L last week. It was missing its front drive shaft so I want to install one.
I just ordered a used front drive shaft online but I now need the bolts that connect everything together. New drive shaft has all the flanges, etc.
What is the pitch/length of these bolts? The part number for the bolts is N800594-S100 (AB-308-D). I believe there would be 8 of them, 4 on each side.
I thought it might be easier and cheaper to just buy bolts from an aftermarket supplier instead of OEM from Ford.
Ford Transmission :: E4OD Shifting Into Reverse And Drive A Bit Clunky
I have a 94 E350 with the 460 and the E4OD trans. that has only 30K on it.
Last weekend I took it on a 250 mile trip (one way) and it ran beautiful until the final steep hill to our vacation house. It started vibrating when it went to down shift and wouldn't pick up any speed, the OD off light was blinking. When I pushed the OD button and it cleared right up. Ran beautiful until I tried to climb that same hill again (same thing happened). It showed the same symptom when I tried to back up a steep driveway during the same trip.
Now it no longer does the vibrating but now has harsh/firm up shifts. Downshifts are smooth though, but shifting into reverse and drive are bit clunky too.
The codes I pulled were KOEO 212 and 668. After I erased the codes the 668 didn't come back. But I did change the MLPS to the new updated one from Ford and its still doing it.
I also found the 40amp mega fuse under the hood was blown too, related? Could a 1/2 qt over filled trans. cause this now too? In NH I added some fluid thinking it was low because I could not get a clear reading on the dipstick but I think the level was up there.
Ford Transmission :: 1987 E350 - Clank Noise When Shifting In To Drive
Our Rv makes a strange "clank" noise whenever we shift into drive. It is a 87 Ford Econoline 350 with the 460 7.5l. The noise is from the back of the Rv kind of near or in the rear differential. It just started over this past weekend.
We live in Alaska and the mechanics are 3 hours away - do you think we would be able to make it to the mechanics and not have to get a tow? How long we could go without fixing the problem?
Ford Ranger / B-Series :: 1996 Automatic Transmission Not Shifting - No Reverse / Drive Or OD
So here in Wisconsin for the last two weeks we have had nothing but ice. That being said, I have a '96 ranger 3.0L, automatic transmission, 4x4. 4 wheel is inoperable at the moment, that's a different story. Here's my question: with the ice, there has been a lot of tire spinning at high RPM's, the other day, I was again stuck on the ice and rocked back and forth had some pushers, thought we were getting somewhere but I went to shift gears and all of a sudden had nothing. No Reverse, Drive, OD, L, 2. Did I blow my tranny? There was no noise or grinding, but the OD light seems to blink. Is there something I can check or look at?
View 4 RepliesFord F-150 - 1997-2003 :: 2002 F150 - Transmission Rattle?
Was looking for some advice on what my problem may be. I just replaced the slave cylinder on my 02 f150 4.2 and two days after I changed it on my way home from work my truck jerked when I was about to turn into my driveway. Then when I stopped I put it in neutral snd it started rattling really bad it stopped when I pushed the clutch in And when i let out it started again. It sounds really bad and im hoping its something I can fix my self and not terminal.
View 4 RepliesFord Transmission :: Long Shifting Into Next Gear When Selector Is In Drive - Code P0732 And P0734
I have a 2008 Ford Escape 2.3L V6. About 67K miles on it.
Recently there's been some transmission problems. When the selector is in Drive, it will take abnormally long to shift into the next gear at normal speeds, and will redline if i hit it hard, but if i let off the gas, it will shift. Never hard.
If I put the selector in 2, it will do the same thing, eventually shifting into that second gear.
Gear selector on one, well, it obviously stays in 1st.
Reverse is fine. All shifts are smooth just take forever, and I get the wrench in the dash (means drivetrain/throttle fault as per manual) only after driving a while. The tranny fluid is still very clean, and this as been going on for 2 months.
Ive taken it to about 6 different places. Half say new tranny off the bat. Other half says clean fluid for that long after the problem started means its def. an electrical problem, and that makes the most sense to me. What it could be?
I'm thinking:
-Tranny Range Positioning Sensor
-Input/Output speed sensor
-TCM reprogramming/replace
- I'll even go with reflashing the PCM.
Elantra XD (2001-06) :: Transmission Shifting On Its Own When Drive Around 25 - 40 Mph
I have read the common problems and went ahead and replaced the Throttle Position Sensor, TPS. Also had a complete tranny flush done. The shifting problem persists, when I drive around 25-40 mph, the car will constantly upshift or downshift on its own even. Sorta like I get to 30 mph and it suddenly decides to downshift, like it has become ultra sensitive to minor increases in torgue(?) or can't decide if it wants to be in 3rd or 4th gear. Did check with Jiffy Lube to make sure they replaced it with SP3 fluid and they did. What else this might be? Check engine light comes on now and then and currently is off.
View 1 RepliesCadillac - Eldorado :: 1989 Transmission - Only Shifting Into Over Drive
Question regarding a 89 Cadillac Eldorado 4.5 V8 FWD, Transmission - 260,000 miles on car, runs great. Last couple of months, I have noticed that it will only shift into Over Drive when the car is cold, sat overnight. It will shift 4 or 5 times into Over Drive no problem. When car warms up, then it will not shift into Over Drive ever again, and I will get a 39 error code. Are there solenoids that I can replace, if so where are they? I'm not sure where to start with this problem?
View 6 RepliesImpala - Chevrolet :: Transmission Slipping When Shifting From Reverse To Drive
2007 Chevy Impala3.5L 6-cyl Flex Fuel engine w/ 4 speed auto trans52,800 miles
Extreme driving conditions maintenance schedule kept.Transmission standard service done @ 32,800 miles which was 20k ago.
PROBLEM:
1) Twice in past three days, when shifting from reverse to drive the transmission has slipped, revving hard with rpms spiked above 3,000 for about 2 seconds before engaging the forward drive gear.
Normally I come to a complete stop of all reverse motion with foot fully on the brake pedal before shifting. Admittedly, I got sloppy the first time noted and still had very slight reverse motion when I shifted.
2) Several times late today, while driving uphill at approx 35 - 45 mph, when the car downshifted there was an extremely brief moment of transmission slippage with spiked rpms. It was so brief each time that at first I thought I'd imagined it until it happened again. Then it did it once on a level surface in a parking lot when having shifted from reverse to drive without problem and was gently accelerating the transmission again slipped for just the briefest moment when the normal automatic shift point was reached. So far, all incidences while driving have been so extremely brief that it was the merest hint of a hiccup.
3) When bringing the car to a complete stop, such as at a stoplight or when parking, as the transmission automatically shifts for the braking of speed, sometimes there is a minor but noticeable thunk sound seeming to come from underneath the car, I'd judge to be somewhere about under the level of the dashboard or slightly forward of that. Could that be from a worn or broken transmission mount? And, if so, could that be somehow causing the slippage problem?
4) This transmission has always, even since new, allowed more roll after being shifted into park, the engine shut off and my foot taken off the brake than any other car I have ever driven. If I forget to engage the parking brake quite tightly, the car will roll forward quite a few inches before the parking pawl holds it, even on the level. I've been told both by the dealership shop and the independent mechanic shop that there is no problem and that this particular engine/transmission combination tends to do this although my particular car seems to do so somewhat worse than average.
ACTIONS TAKEN SO FAR:
1) Have made an appointment to take the car into the mechanic.
2) Will check the transmission fluid level per instructions in the owner's manual tomorrow when I have daylight to see what the fluid level and color on the stick looks like.
NOTE:
1) I periodically check the transmission fluid level and it has never been low or discolored. The shop checked it for me, along with making sure everything else was road trip worthy, for an emergency 1,000 round trip in late November, just three months ago. No problems then.
2) No evidence on the garage floor of any leakage. Garage floor is dry.
QUESTIONS:
1) I presume the first step is for the mechanic to check the fluid level and examine for any leaks?
2) If the mechanic cannot duplicate the problem in a test drive, then what?
3) If the problem cannot be duplicated and no apparent cause found, I presume that the prudent course of action is to go ahead and have standard transmission maintenance done (i.e. drop the pan, check for debris, drain and replace with fresh fluid) then see if that halts the slippages?
4) Given that this car has already had failures of the power steering pump, water pump, and part of the wiring harness, and has a fuel pump starting to get noisy, despite aggressively maintaining all standard/preventive maintenance, that perhaps it is time to think of replacing this car, especially if there proves to be any truly major transmission problem found?
Sonata I45 (YF - 2011+) :: Transmission Lurch / Shifting Hard Into Drive
So my car has recently begun having an issue shifting hard into drive after it warms up. It doesnt shift weird in any other gear or while driving. I had the trans temp sensor replaced last year under the tsb due to it shifting weird in all gears and a CEL. I was thinking either the fluid level or another bad sensor.
View 2 RepliesAccent LC (2000-05) :: 2001 GL Transmission Shifting Hard Into Drive
I have a 2001 hyundai accent GL the transmission has started shifting hard when it shifts into drive. It shifts fine and smooth from first to second but when it shifts into drive it hits drive hard and sometimes it acts like it doesn't want to shift and if you let up on the gas it will go ahead and shift, but when it shifts to overdrive it seems fine but hits hard when it down shifts back to drive. Also I have noticed a couple times when it goes to shift into drive the engine seems like it revs up some but when you let off the gas it goes ahead and shifts.
View 3 RepliesPassat (B6) :: Transmission Having Delayed Engagement When Shifting Into Reverse And Drive
I bought my '07 Passat 2.0T Wagon as a CPOVW 6 weeks ago. It had 4700 miles on it. I complained about the transmission having a delayed engagement when shifting into reverse and drive. (it drives normally however with positive shifts and is very enjoyable) I was told it was normal and not to worry. (could it be designed-in to soften the engagement?).
This week I noticed a light "thunk" in the right front when re-applying power while coasting below 40 MPH. I never noticed it before but I usually strive for smooth driving so that may be why. I've had other Aisin Warners but they were in Volvos. I got out of a '99 Volvo Cross Country because I didn't trust the driveline. Am I going down the same road?
Ford - Explorer :: 2002 - Transmission Shifts After 3 Seconds - Won't Run Immediately After Shifting?
I've just bought a used 2002 Explorer Sport Trac (Automatic) 120k+ odo and what I've noticed whenever I shift from Park to Reverse or to Drive it takes about 3 seconds before I feel a slight jerk moving forward before I can step on the accelerator for the vehicle to move backwards or forwards but if I step on the accelerator right after shifting to any gear except Neutral it won't run immediately as if the clutch is disengaged and after about 3 seconds it will suddenly engage. Is this normal or is there something wrong with the transmission?
View 3 Replies