Ford Super Duty (1999-2016) :: TPS Fault Lit Up On Message Center When Taking Off From A Light
So on my way to work this morning taking off from a light on a smooth blacktop my message center lit up with "tire pressure sensor fault". is there any way to tell which sensor it is without a scan tool?
View 11 RepliesFord Super Duty (1999-2016) :: Tire Pressure Sensor Fault Message Comes On And Go Back Off
Got a 'Tire Pressure Sensor Fault' message a few times on the way back from Florida. Tire pressures were all fine. Hate that it doesn't say which monitor has the problem. Anyway... it comes on, but after a few minutes goes back off. Saw it a total of three times over the course of 1,000 miles in two days. Is this the sensor failing and requiring replacement? Or is the system itself starting to fail? Would ESP cover this?
View 6 RepliesFord Super Duty (1999-2016) :: Wiring Fault On Trailer Error Message With A Beep
Every time I touch the brakes I now get a very annoying beep and an error message that says "wiring fault on trailer." I don't have a trailer hooked up so not for sure what's going on. The error message on the console I can live with but that loud beeping is driving me crazy.
If you hit the brake and keep the pedal depressed, then you only get the initial beep and then it goes away. The problem for me is I live north of Dallas so if I'm in traffic then I'm constantly hitting the brakes. I called my dealer today so I'll wait to hear what they have to say.
Ford Super Duty (1999-2016) :: Clock Spring Suffered Water Damage - Replaced But Still Fault Message
I have a ford f350 2014 that had some water damage, the clockspring suffered water damage so I replaced it along with the steering column module.
The clockspring was brand new from ford, already centered, I pulled out the plastic tab during install.
Cluster has SERVICE ADVANCETRAC error and IDS is shows fault with the steering angle sensor. (see picture)
Do these new sensors have to be reset and calibrated to work, or does this FAULT message on IDS indicate a wiring problem?
Ford Super Duty (1999-2016) :: Trans Fault Light On?
Is there some sort of reset to turn off the Check Engine light? I had replaced the TPS sensor, and after a day the engine seems to have stopped the high idle and returned to normal, and now it still has the check engine with the same error code, but the problem seems to be resolved. My previous post: [URL] .....
View 14 RepliesFord Super Duty (1999-2016) :: 2008 - Message Flashing - 4x4 Low?
I just traded in my trusty, never had a single issue 2008 Ford F150 with 53k miles for a 2008 Ford F350 with 112k miles. I figured the extra miles were okay, because it is a diesel. I purchased the truck to pull a 31’ 12k lbs when loaded toyhauler, and I have a 14K weight distribution hitch.
Just in case this makes a difference, here is some background information. I have a 2008 Ford F350 XLT 6.4L CrewCab Long Bed. Before purchasing it, I had Ford do a performance and safety inspection. Everything came back clear, so I bought it. The day after purchasing it, I changed all the fluids for peace of mind, ie. rear diff, transfer case, transmission, motor oil & filter, fuel filter, and radiator fluid.
Here is the problem. Occasionally, the 4x4 Low light will start blinking/flashing. Sometimes it will only flash once or twice and go off, other times it will flash for 15-20 seconds and then go off. There is no pattern to when it happens other than it seems to do it mostly when slowing down or breaking. It is very sporadic. I don’t drive very far for work, so I can go an entire week without seeing the light come on, but if I hit the highway for 30-45 minutes, the light will eventually turn on.
When it flashes, occasionally, I get an RPM increase…almost like it’s trying to engage natural or shift into 4x4 low at highway speeds…which causes me concerns. I took it to Ford and after 50 miles of driving it around, they could not get the 4x4 low light to come on. They said they pulled codes but there were none to pull. They reflashed the PCM and charged me $99 to not fix my problem.
I can shift into 4x4 high and 4x4 low (with the window rolled down, I can hear the shifting from 2wd to 4wd high and then to 4wd low and back to 2wd), so I don’t think it is a blown fuse or the control module. I removed and cleaned the wire connectors to the shift motor on the transfer case, and that didn’t fix it. I was thinking about replacing the rear diff abs speed sensor in hopes that will fix it. I think that maybe it’s a wiring issue, which I wouldn’t even know where to start.
I was getting 14 mpg before the reflash and after, I am now getting 8 mpg. Does this seem right? Or is there a learning period after a reflash before my mpg gets back to normal.
Also, the automatic 4x4 drive doesn't work. I don't think its holding a vaccum. I don't think it is related to the 4x4 low light coming on when I am doing normal driving. I can use the lockers to get 4x4 to work correctly. Infact, Ford is the one that told me the auto doesn't work.
Edit: I also noticed that if I flip ON any of the upfitter switches (ie AUX 1, AUX 2, AUX 3, AUX 4) the 4x4 low light will flash constantly until turned off. I currently don't use any of the switches for anything.
Ford Super Duty (1999-2016) :: Trailer Module Fault All The Time At Start Up?
Im getting this almost every time I start it up. It happened once about a month ago, then more often. Now almost every time.
Truck has 1700 mi
I hate to have to bring it to Ford so soon
Ford Super Duty (1999-2016) :: Cleaning Exhaust Filter Message
Is this the same thing as the regen? Got it for the first time yesterday at 775 miles. Just curious. On a related note, I've tried to run around town some with 5th and 6th locked out (speeds of around 55-60 on a regular basis, running about 2300-2500 rpms) to try to run this process...am I doing it wrong?
View 10 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Check Gas Cap Message Came On
OK....my gas cap (5.4 gasser) wasn't put on properly at the gas station. A couple of blocks later, the "Check Gas Cap" notice came on. I stopped a few blocks later, and installed the cap properly. The notice STILL came on. After messing with the cap 4 more times, I gave up, but the notice is still on. Do I need to have it "erased" like a code, or is there a problem with the cap? Everything LOOKS fine...
View 2 RepliesFord Super Duty (1999-2016) :: Shutting Off Low Tire Pressure Message?
How to shut off the Low Tire Pressure message? My tires are at 65-70 pounds and the message still shows up at every start up.
View 6 RepliesFord Super Duty (1999-2016) :: 1993 F350 - Clutch Position Switch Fault?
I'm getting a random 'no start' fault which I think is related to a clutch position switch. The dealer tells me the clutch pivot bushing and master cylinder push rod are worn out, which is causing the switch not to close when the clutch pedal is depressed.
1993 F-350 7.3L Diesel 5 Spd 4x4, Std Cab, 8 Box.
Ford Super Duty (1999-2016) :: 2011 F350 - Tire Pressure Monitor Fault
I've looked at this 10 ways to Sunday, but the play on words have me questioning if it is the same thing. My truck says Tire Pressure Monitor Fault. I have a 2011 F350, if that makes a difference. I checked all my tires, they are about 80psi each, front and back. What could be the problem? Is it something to take to a Ford Dealer or something I can fix myself?
View 7 RepliesFord Super Duty (1999-2016) :: 2010 F250 - Trailer Brake Module Fault
2010 F250 Lariat, cab and a half, PSD. 5600 miles.
Sunday I started the pickup and received "trailer brake module fault" in the message center. I wasn't pulling so wasn't too concerned - hit the reset and continued on.
Sunday night I started the pickup again and received the same message followed by "check brake system". I also lost illuminated gear selection, the traction control active symbol was displayed and the traction control "off" (PB) was illuminated. After several attempts it reset, everything returned to normal and I was able to get home without incident.
Monday morning it wouldn't start. It indicated "trailer brake module fault", "check brake system", traction control active and off, no gear indication, the odometer indicated "-------" and it did not react to the key in the start position.
Tuesday morning I attempted to start and it was the same as the previous attempt. I noticed that the theft prevention appeared active (flashing) so I removed the key, locked the doors, unlocked the doors, tried again - no joy.
I kept trying while holding my mouth in different positions and finally by the grace of God it fired. I delivered it to the dealer.
The dealer called yesterday afternoon and reported that everything is a result of a bad trailer brake module. The new one is to arrive today, they will install and everything will be peachy.
I asked if they could just unplug it and reprogram the truck to believe it never had one - the service writer said it can't be done, different piece parts on trucks with or without trailer brakes.
I really have no choice but to push the "I believe" button and carry on but I am slightly concerned. The fact that the trailer brake module can cause catastrophic failure doesn't seem too cool, I don't have a real warm and fuzzy feeling associated with venturing far from pavement, reliable communication or alternative transportation.
In the meantime I suggest that no one take "trailer brake module failure" lightly.
Ford Super Duty (1999-2016) :: Display Is Showing Wiring Fault With No Trailer Attached
I have a 2008 F450. What may be going on with my truck. In the past the truck would blow the fuse for the door locks. Currently the display is showing wiring fault with no trailer attached, the horn is not working and the cruise control has stopped working. I've covered the basics and checked all relays and fuses and haven't found a faulty one yet. I'm thinking bad ground or possibly bad GEM module???? I've read and read topics and am more confused as to what it could be now than when I started.
View 3 RepliesFord Super Duty (1999-2016) :: 2008 - Message On Dash About Trailer Wiring?
Driving the truck today I noticed mssg from info on dash " problem with trailer wiring". I wasn't hauling anything. the message went away on my next stop when a truck was turned off. On my next stop, I was pulling into a parking space truck stalled and I saw another message saying something like " please pull over safely and stop a truck." Luckily I was already parked. the truck would not start or even turn over. after about an hour truck started but brake symbol was on the dash.
View 10 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Message Center Is Not Working At All
A buddy's 2012 f250 message center is not working at all. He replaced the fuse and it's still not working. The gauges work but not the high tech information center. He isn't sure if it's out of warranty because he can't see the miles. I'm not sure that's it's anywhere related but his back up sensors do not work either.
View 3 RepliesFord Super Duty (1999-2016) :: When Connecting To Sync - Metadata Missing Message?
When I go on longer trips I connect my iphone 4s via the sync usb so that it can recharge; I still stream audio via bluetooth but it reads all the music from the phone and tells me some of my tracks are missing artist, genre, album interrupting my music after 1-2 minutes of scanning my songs.
One solution would be to find and fix the songs with missing info but I have a lot and don't want to go there. Another solution would be to get a faster 1amp charger from 12v socket instead of the usb 500mA. I may go there eventually but I already have the usb cable.
Any way to tell sync to just leave it be and don't tell me each time?
Ford Super Duty (1999-2016) :: F250 - Oil Life Meter Reset Message
I'm having trouble resetting my oil life meter in my 16 F250. I think I'm doing exactly what the manual says but nothing is happening. I turn the ignition on and wait a second for the ford start up graphics to finish and then press the gas and brake at the same time as far as they will go. The manual says after 3 seconds I'll see a message saying the reset is in progress but I don't get any message on the screen. Am I doing something wrong?
View 5 RepliesFord Super Duty (1999-2016) :: 2006 F350 - Check Gauges / TBC Fault / Warning Lights
Just got a new-to-me 2006 F350 Super Duty XL with the 5.4L V8 and 5-speed auto. I haven't had a full-size truck in a few years and forgot what I was missing!
When I bought the truck, all gauges were inoperative except for the fuel and oil pressure gauges. The previous owner told me they would work intermittently and at some point just stopped. The usual warning lights - ABS, CEL, and "the wrench" - were all lit, and from Googling and searching this forum, it looked like an easy fix - probably a pinched or frayed shifter wire, or possibly a cluster repair.
I took it home and did a self test on the gauges. The "sweep gauges" made everything swing fine, so I was thinking it might not be a problem in the cluster. I pulled the steering column apart, removed the Tow/Haul overdrive wire from the plastic retainer, re-ran it with some slack, taped the end where it comes out of the shifter (even though I saw no breaks/frays) cleaned the connections, gave it a dollop of dielectric grease in the connector, and put it all back together. VOILA - GAUGES and no warning lights! You can imagine the touchdown dance in the driveway.
Fast forward a few weeks and....back to no gauges and warning lights lit. Figuring the overdrive wire had finally given up, I ordered and installed a replacement shifter figuring it was an easy and cheap fix. No joy - same problem. Tried cleaning and reseating the connection. Nothing. I've searched FTE like mad and it seems like 95% of the problems are with the wire exiting the shifter fraying and/or blowing a fuse, but this is a new shifter. I've also checked fuses #2, #24, #33, #36, #41, and #45 (some referenced #19 but I don't have a fuse there). All were unbroken - just put them back in and reseated firmly. I did a code pull via OBD2 and have a "rear catalytic efficiency degraded" code...not sure if that's related, but figured I just had an exhaust issue.
I may take the dash cover off and try to clean and reset the connections on the gauge cluster, as well as do the same for the PCM. Is it possible that the tow/haul overdrive wire to the PCM (where the shifter connects to) is bad? How to test and/or replace if it comes up bad?