Ford Super Duty (1999-2016) :: 2015 F350 - Rear Axle Pinion Seal Leak
I was looking underneath the truck yesterday and saw that the rear end pinion seal was leaking. Looked like it had been for a while. Truck has 35,850 miles on it. Unscrewed the fill plug and a lot of pressure is released. So I'm assuming the breather is clogged somewhere along the line. I have an appointment at the dealer on Friday to see whats wrong. What is supposed to be at the end of the breather tube? Mine has a barbed 45ish degree fitting on the end of it. Its a SRW by the way.
View 5 RepliesFord Super Duty (1999-2016) :: Front Axle Seal Leaking?
I noticed the other day after my truck was parked on a bit of a angle there was diff oil from the passenger side on the ground. reading a bit on here i learned the axle seals are way in the front housing close to the front diff. and yesterday driving a heavy load around my front brake driver side got stuck on a bit and over heated and was smoking, couldn't even touch the rim it was so hot. anyway about this axle seal i got the hub off right now but cant seem to pull out the axle assembly through the knuckle but i see i have to pry and most likely wreck that seal. Looking for a link of piuctures or how to replace the axle seals in the housing.
View 11 RepliesFord Super Duty (1999-2016) :: Right Front Axle Seal Leaking Continuously?
99, F250, 4X4, V10, 72,000 miles. I have had the front axle seals replaced three times in the past 3000 miles, and the right continues to leak. My mechanic screwed up three times?
View 6 RepliesFord Super Duty (1999-2016) :: Leak In Front Axle Shaft
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 2 RepliesFord Super Duty (1999-2016) :: 2005 - Oil Leak From Front Axle?
I have an F250 4.2 diesel 4x4 double cab. Its a2005 model. I noticed an oil leak from the front left axle. It looks like its leaking from the axle tube. See pic attached. Is a seal probably worn? How big a job is this to fix.
View 4 RepliesFord Super Duty (1999-2016) :: F250 - Leak In Front Axle Shaft
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Knuckle / Axle Seal Replacement
Replacing the knuckle/axle seal due to my hub not holding a vacuum. I finally got the seal off the axle after several minutes of beating, but it finally came off. During the beating the metal shield that was in back of the seal took a beating as well and can not be reused. Is it really needed?
In this thread the pictures show that the shield was not installed after the seal was replaced. The shield does serve a purpose to keep crap out of the seal though.
Ford Super Duty (1999-2016) :: 2003 Excursion - Outer Axle Seal Installment
Do I need a special tool to put the outer axle seal on a 2003 excursion? I could make one if I new how far down it needs to be. I'm replacing the needle bearings in the back of the hubs and it looks like the last seals were not on far enough and the hub tore them up....
View 13 RepliesFord Super Duty (1999-2016) :: Parking Brake Not Working - Burning Axle Seal?
Will leaving the parking brake on burn up the axle seals? My parking brake isn't working well at the moment. I need new ones from all the fluid my bad seals leaked on them. So, at the moment they just scrub a bit while its engaged. However, today I found out that my parking brake light for one reason or another is not working and I got in a hurry and didn't release the brake. by the time I got to where I was headed (about 15 miles), I could smell gear fluid burning and my driver side rear was smoking. I'm hoping its the fluid that was already soaked into the shoes. I did find a drop of fluid on the bottom of my brake caliper.
View 5 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Rear Hub Seal Leak?
I have a 2000 F250 4x4 7.3 - About a month ago I drove across town and then noticed a strong hot brake smell from the rear of the truck. When I drove home about 2 hours later it was gone and didn't return until today. Today I stopped at a light with my window down and got the same hot brake smell, looked in the mirror and saw smoke coming from my drive's side rear wheel.
I carefully drove home (the smoke was now gone, all i did was cycle the parking brake release a couple of times) and pulled the wheel off. Rotor was really hot but smooth and clean. Brake caliper and pads looked great (no sign of the pads glazing or dragging, dry as a bone). The inside of the rotor was wet with oil. The brake shoes and components were soaked with the same fluid/oil.
Does this sound like a typical hub seal issue? Excuse my ignorance since I haven't had the rear hubs apart before but does the gear oil in the rear diff go into the axle tubes? I know the front tubes are dry but I didn't know if the rears are different. The amount of fluid on the brakes seems to be more than the little bit that is inside the hub. I need to pick up the parts and rent/purchase a couple of tools to replace the seal so I want to be as sure as possible that I'm on the right track...
Ford Super Duty (1999-2016) :: Slow Leak Coming From Rear Main Seal
If I use ATP AT-205 stop leak to stop a slow leak coming from the rear main seal, will it last a long time? And if it stopped working eventually, would adding more stop the leak again?
Also, I'm going to have the transmission out anyway, so how many hours would it probably take to just replace the seal at that point? And someone told me some seals were two halves that fit together as one, and others are just all one piece. Is that true? It would seem to me that a two piece seal like that would start leaking prematurely.
Ford Super Duty (1999-2016) :: 2001 F250 - Transmission Leak - Replace Bearing / Seal?
I have a 2001 F250 Super Duty 5.4 Triton motor with a Transmission Leak. I have drained the Transmission, replaced the Transmission pan gasket and filter. The auto parts store also had me purchase the Torque Converter bearings/seal along with enough transmission fluid and a bottle of Lukas Transmission fix. Do I really need to replace the bearings/seal if I have everything else already ?
View 2 RepliesFord Super Duty (1999-2016) :: 2004 F350 - Huge Rear Axle Fluid Leak
Put new backing plates, parking brake shoes, springs, etc on my 2004 F350 DRW 4x4. Replaced the inner hub seals and axle o-ring. Filled with Ford Rear end lube and went for a test drive. All was well. Went out last night to take her out again and I've got diff lube running out of both sides on the inside of the rims. Did Ford sell me the wrong seals? Could I have installed the seals wrong? Ford seal part number is 4C3Z1S177A. Axle is a Dana 80, confirmed by reading the tag on the diff.
View 2 RepliesFord Super Duty (1999-2016) :: 2015 - Front Axle Leaking A Lot?
I have a 2015 F250, cc 4X4 PSD. It has 22,000 miles on it. I notice a small quarter sized drop of oil after it is parked by the right side front wheel. It is coming from behind the dust cover and universal joint where the axle goes into the tube. I dont know how long it has been leaking. My issue is I am about 800 miles from home on a camping trip, have to go back to work Monday, and lcoal dealer here can't take it in till next week. So, if the hubs are not locked and the truck is in 2 wheel drive, the gears shouldn't be turning right? I assume it is ok to drive home. I didn't want to pull the plug and check the fluid because if any runs out and leaves a stain on the cover, I don't want ford trying to deny warranty claiming I messed with it first.
View 5 RepliesFord Super Duty (1999-2016) :: Clicking Noise From Front Axle
I have a slight problem and don't know how serious it is. I own a 2003 F350 with a lift kit. After my drive shaft shattered last September. due to a U-Joint a clicking noise started up in the front axle area after we locked the hubs so we could crawl it down the road out of traffic.
What would be the likely causes and how much would a typical repair/replace cost?
Ford Super Duty (1999-2016) :: Front 4x4 Axle Still Turn When Unlocked
I am not up on the exact operation of the hub lock/unlock on superdutys but when following them, I can see the front axles still turning with the wheel. So even with them "disengaged" they still turn with the wheels?
If that is the way they are designed to do, why? Seems like efficiency could be gained by having them actually disengaged when not needed. And save wear on the inner housing seals.
Ford Super Duty (1999-2016) :: 2006 - How To Tighten Front Axle
It's the Right Front Axle Shaft on my 2006 F250 where it goes into the Hub/Bearing assembly.
Seems way to loose to me but after I removed the Lock-Out, I discovered the Axle Shaft is held in by a Snap-Ring not a Nut (WTF) so how do I get this tightened up
Also it's my understanding (I didn't remove) between the Axle & Steering Knuckle there's a rubber O-Ring. Could all this play be from that O-Ring being wasted Although that doesn't seem likely to me, Iam worried what's wrong
Ford Super Duty (1999-2016) :: Front Axle Shaft Wiggle
So the other day I took my locking hubs out and cleaned them really good. When they were out I noticed I could grabs axle shafts inside the hub and wiggle them quiet a bit. Is that normal?
View 2 RepliesFord Super Duty (1999-2016) :: Front Axle U-Joints Rusted
I have my front axles out to replace the U-Joints but they are rusted in there. Even the C-Clip is fused/rusted in place. I use my flat wheel grinder and ground out the C-Clips but the U-Joint caps wont budge. Been soaking in penetrating oil too. Any way other than drilling them out?
View 1 Replies