Ford Super Duty (1999-2016) :: F250 V10 - Heater Hose Inlets Or Outlet?
99 F250SD V10. There are two connections on the heater core at the firewall. Is there an 'inlet' and an 'outlet' or does it not matter? Put a cummins in the truck, the V10 has been out for a while and cant remember which one is which.
View 5 RepliesFord Super Duty (1999-2016) :: F250 V10 - Leak From The High Pressure Hose On Gearbox?
My uncles 1999 v10 started to leak from the high-pressure hose on the gearbox. Replaced the hose which lasted for a short time but is now leaking at the same spot. The hose swivels, is this normal, seems like a dumb design for a pressure hose. Also is there a certain trick to doing this hose? He also insists on using PS fluid instead of the ATF it calls for. Could this cause a problem with the seal?
Edit: Also the truck has been lifted on 35s since 16k miles and its now roughly at 170k. He tows with it as it is his work truck. But the truck is well taken care of.
Ford Super Duty (1999-2016) :: 2008 F250 - Coolant Leak Above Lower Radiator Hose
I'm trying to troubleshoot a leak on my 08' F250 with a 6.4 powerstroke. It's been dripping coolant when cold pretty aggressively. Once the truck heats up, the coolant leak seems to mostly go away.
Here's a picture of the drip, it's marked by a dart, so you can see the location from the top (second pic). The radiator house connection around the engine seems dry.
Pic from Top ....
What's hidden here that could be causing the leak?
Ford Super Duty (1999-2016) :: 2008 F250 - Oil Leak Form Radiator Hose At 122 K Miles?
Where this small leak coming from. Under my radiator hose. Took a pic of the leak.
View 8 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Heater Core Replacement
I recently replaced my heater core on 2001 F250. Would be a simple job if it weren't for the quick connects on the hoses. Any tool to take these apart on the truck where space is limited?
View 1 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Heater Core Replacement?
Started to attempt to replace the heater core in my 08 SD 6.4. Didn't know the entire plenum has to come out in order to replace it. How to remove the plenum? My buddy is a Ford tech but I just am not getting what he is telling me and there is next to nothing coming up when I try to search.
View 2 RepliesFord Super Duty (1999-2016) :: V10 - Coolant Leak Where Heater Core Tube Goes Into Intake At Rear Of Engine
I have a leak where my heater core tube goes into the intake at the rear pass side of engine. I have read that this part is pressed in. I dont want to remove the intake since i just paid $400 to have a new gasket kit put on. My question is can I bypass this tube with a hose from the water pump like in this video?
FORD 4.6 , 5.4 , 6.8, HEATER HOSE UNDER INTAKE REPLACEMENT THE EASY WAY !!! - YouTube....
If I can do a rubber hose like in the video I was to make sure that the tube just goes through the intake and that it does not supple coolant into the intake??
Ford Super Duty (1999-2016) :: ABS Light Came On After New Wheel Hub Assembly
I just put a new front driver side wheel hub assembly on last week and i discovered two things. The metal plate that goes in behind the wheel hub assembly needs replaced but idk what it is and i need a new axle seals. But when i put the new hub assembly on, the abs light came on and i cant seem to figure out why? Also my front drivers side of the truck is still making a clunk noise when i hit a bump. Input on that too?
View 6 RepliesFord Super Duty (1999-2016) :: Wheel Bearing / Hub Assembly Going Bad
How can you tell when your wheel bearing/hub assembly is going bad? I am hearing what sounds like "metal-on-metal" and I've already changed the brake pads, but the sound still persists. I was thinking about changing out the brake rotors since I did notice an inch long score on the rotor when I was replacing the pads. I don't want to spend a couple hundred dollars on rotors to find out it was my wheel bearing/hub assembly all along.
View 8 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Hub Assembly Removal
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 RepliesFord Super Duty (1999-2016) :: Blower Assembly Is Filling Up With Water
My blower assembly (not at the blower but in the box below it) is filling up with water. Any way to look into besides drilling a hole in the bottom of the box?
View 1 RepliesFord Super Duty (1999-2016) :: 2007 4x4 Hub / Bearing Assembly Part Number
I am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 RepliesFord Super Duty (1999-2016) :: Hose Diagram For 4WD?
Is there a hose diagram for the four wheel drive? My hoses are dry rotted at the hubs so I was wondering if there are more somewhere that I have to change?
View 2 RepliesFord Super Duty (1999-2016) :: 2002 F250 Knocking / Loose Front End Assembly
My 2002 F250 is knocking loose the front end assembly--the gasket is worn out. So I was shopping around and was considering a beefed-up front end assembly.
View 3 RepliesFord Super Duty (1999-2016) :: Loose Hose Under Truck Blowing Oil
I crawled under my truck today (2011 6.7 w/delete kit, straight pipe) and found a black rigid hose had signs of oil being blown out. The hose was about midway towards the back on the drivers side. There was fresh oil around the outside of the opening of the hose and some on the frame around the hose opening. I traced it back up into the engine into something that I'm not sure what it is and couldn't find it on any engine diagrams. So I've taken some pictures, what it is, what it's connecting to in the engine and why it might be blowing oil out. There isn't a lot, I haven't seen any on the ground where I park but it's obviously coming out, I guess when I drive. Pics attached.....
View 4 RepliesFord Super Duty (1999-2016) :: Hose Coming Through Radiator Fan Shroud?
Just picked up my truck from the dealer after a trans flush. While it was there I had them replace both windshield wiper nozzles. They called and told me the hoses needed to be replaced as well--- OKAY fine do it.
Come home and decided to "make sure" the trans fluid was at the correct level.
Open the hood to discover a loose black hose approximately 1/4" or so in diameter coming out of the radiator shroud directly at center of the top. The end of the hose was somewhat towards the passenger side battery.
I figured okay the tech probably just left my old windshield wiper hose on top of the motor and forgot to discard it...
I follow the hose and it appears to go in between the rubber seal for the shroud and the plastic housing. I looked back behind the fan and can see the hose twirled around an aluminum or stainless steel pipe coming up just in front of the fan but behind the numerous condensers...
MY question is two fold: Should this hose be here, or is it indeed the wiper hose that got sucked into the fan?
if it is supposed to be here, what does the end that was leaning towards the passenger battery connect to? it certainly appears to have been previously connected to something whether the washer or some other barbed fitting....
Ford Super Duty (1999-2016) :: Cannot Find Hose For Canister Pressure Valve?
I can't find canister pressure valve hose. It looks cut from the pressure valve in some way. Tried following it from gas tank but I've lost it through the chassis.
View 4 RepliesFord Super Duty (1999-2016) :: 2000 F450 - Rear Axle Assembly - Hub Retainer Threads On Housing Are Stripped
I have a 2000 F450, 7.3, 4x4, dually, VIN 1FDXF47F0YEA44380, with 30k miles, That needs a new rear axle - hub retainer threads on axle housing are stripped (nut welded on by previous owner). This axle is a case ID F81A-4001-BK, 4.88 ratio, 11.25 ring gear, with a 41.5" spring center. I have heard that the '99-'02 axles had issues until Ford switched over to the later square housed axles in 2002 or 2003 (Dana 110, I think). Is it possible to adapt these later (2002- 2004) axles onto a 2000 F450? And if so, what would be involved?
View 3 RepliesFord Super Duty (1999-2016) :: Broken Hose Near Driver Side Front Tire
What this might be? (see pic)....
View 14 Replies