Ford Super Duty (1999-2016) :: Hesitation / Idle Rough / Stalling Sometimes - Power Loss
Here is this wonderful 5.4 's issue now, sometimes it will idle rough, sometimes it wont. sometimes it feels like it wants to stall, other times not. if im driving about 30mph up a hill around 1700 rpm, the engine feels like a bucking horse, it will kinda want to produce the power, but cant seem to find it till the trans drops to a lower gear. With this engine power loss is unacceptable because it came out of the factory with no power, i cant afford to loose more.
there is no check engine light. its been doing this on and off for a week. i dont drive it much, may 15 miles a day. i thought maybe it was bad gas , i had it sitting for a month, but since then ran almost 2 tanks of gas through it. Seems to act the worst when driving it, then letting it idle for 5 mins, then drive it again, that's when its very noticeable. no smoke from exhaust, no mixing of oil and anti freeze, plugs are a year old, filter is new.
Ford Super Duty (1999-2016) :: 2003 F250 Keeps Stalling / No Power And Rough Idle
The 2003 F250 5.4 Superduty has no power and keeps stalling. If I floor the gas it just stalls. I've replaced the pcv valve and line, the fuel pump relay, the fuel pump, and cleaned the tank, changed out the gas, added Lucas, and it just won't run right. Desperate, and no codes are coming up...
View 5 RepliesFord Super Duty (1999-2016) :: 1997 F450 Idling Rough / Died And Would Restart But Has Zero Power
It has 100k on the clock. I bought it about 2 years ago and only put about 500 miles on it. It is only used as a farm truck. Historically it would periodically die at idle in park. Would always start up immediately and run fine. Plenty of power.
Today the truck started up and idled a few seconds and started idling rough. It died and would restart but has zero power. Put it in gear and it would die. Did this a few times now can't even get it started.
I checked all fuses. I checked the dist cap and rotor. Don't look the best but don't think this is the problem. I get the same result on both front and rear tanks. From what I have read sounds like a fuel pump or regulator. Where is the regulator located?
1997 F450 superduty 7.5 gas ...
Ford Super Duty (1999-2016) :: 2001 F250 - Stalling When Idling Down On A Cold Start
I changed the IAC valve 2 months ago because my truck kept stalling when idling down on a cold start and that fixed the problem. A few days days ago when starting it started revving to 2 - 3 K and won't IDLE down now? I changed the IAC again and that didn't work. What else should I be looking at to stop it from revving so high?
2001 F250 5.4 111,000 miles super duty.
Ford Super Duty (1999-2016) :: 2005 - Idling Rough And Missing - Code P0506
2005 5.4l... Its giving me a code p0506 rpm to low idle air control system called for new one they said my truck don't have one said only up to 04 so what now truck idles rough n when u step on it it misses so bad its not funny feels like its laying over...
View 3 RepliesFord Super Duty (1999-2016) :: 2002 F350 Stalling Out / Runs Rough Like There Is Air Bubble Then Smooths Out
2002 f-350 diesel 4x4 7.3l. It stalls out a few times lately( and starts right back up) and it runs rough like there is an air bubble then smooths out. Changed 1 fuel filter and the pcv valve. 96,000 miles.
View 6 RepliesFord Super Duty (1999-2016) :: Idling At Startup Make Truck Deliver Power Smoother / Battery Light Stays Off
I would like to know what's happening, it seems as if idling for a minute to let my transmission temperature dial raise past the lowest line on the dial fixes or at least drastically reduces a couple issues.
The truck will deliver power much smoother off the line. I've been concerned about this for a while. The degree to which it happened wasn't constant but it seems like the truck is having trouble grabbing on (so to say) to the power coming off the line. I sort of liken it to a rope. When I give it the beans the rope goes forward but it takes a half a second or so for the truck to "grab" on to the rope. Never hard shifts, it's just delivering the power off the line or from a near stop.
Idling for a minute seems to fix this, power delivery is smooth off the line. Transmission dipstick was nice and pink but smelled slightly burnt. This is with the engine cold overnight. Didn't have time to do multiple wipes or check in the handbook for the proper methods of checking fluid, I just pulled it out quickly to take a look before heading out. Fluid covered the whole tip.
Second issue that seems to be fixed is that the battery light doesn't come on nearly as much and not for nearly as long. Typically the battery light will come on and off seemingly on its own whim during the drive. However, it seems to stay more consistently off if I idle right after startup.
Now bear in mind I baby my truck, I don't rev it high right after startup. Just low enough to cruise around the parking lot until I hit the road then I accelerate up to 40 - 60 depending on my route. I'd gladly give it the minute to warm up in the future but if I could get down to the bottom of this that'd be preferred, I doubt this is required behavior.
I do realize that these issues are not tied to startup behavior but I find it interesting that idling for a minute at startup to let the transmission gauge rise seems to mitigate these symptoms.
Ford Super Duty (1999-2016) :: 2000 - Rough Idle - Low On Power
I have a 2000 F250, SuperCab, 5.4 triton, 100,000 miles. It's been a great truck - got it at 63,000 miles. Once engine warms up, it has rough idle, and shift rough. I can give it gas to RPMs up and it smooths out some but is low on power. If this was my 76 F150, I would guess the vacuum hose off the intake manifold to the transmission came loose.
View 6 RepliesFord Super Duty (1999-2016) :: 2003 - Rough Idle And Low Power
I've got a 2003 6.0 that's got a rough idle and low power situation. Doesn't matter hot or cold it has a hard start issue but when it finally starts it has a rough idle, sometimes it has low power on take off but not always. FICM has 48.8 volts coming out, exhaust just had a new y-pipe (had a cracked bellow) absolutely no smoke coming out. When I drive it hard it's like a rocket no rough spots just did oil with filters and fuel filters, blue spring upgrade, and cleaned out the turbo.
View 2 RepliesFord Super Duty (1999-2016) :: Loss Of Power And Rough Idle
Last night, I left it running while unloading a trailer and come back to notice it was idling abnormal. I jumped in it and tried to move it and there was a noticeable loss of power. I unhooked the trailer and tried to get it home. I only made it 1/2 mile down the road when it started spitting and sputtering (surging ever now and then) to a level that it died completely. I was able to start it back and get it out of the road but had to be pulled into a drive. It got to a point it wouldn't start back at all.
Today it started up however still had a rough idle and really has no power to speak of. The more I messed with it the less power it seem to have.
I have searched the forums and tried these things:
1) Checked the oil and noticed it was on the low end of the operating range. I put some in it to put it back to normal.
2) Disconnected the ICP
3) Changed the crankshaft position sensor
4) I dumped the fuel bowl after it completely died (in case it had any water in the fuel bowl).
The fuel filter was just changed 2 weeks ago. The fuel pump seems to be operating correctly (or it at least refilled the bowl) and started again with a very rough idle.
It doesn't have a engine light on nor do I have anything to read any codes it may be showing.
Ford Super Duty (1999-2016) :: No Power / Going Uphill Is Rough / Gas Engine Loud
I had a leaking coolant crossover so had to remove that and replace it with a new one. In doing so i removed the air assembly, throttle body, fuel injectors, and Spark plug coils. I reassembled everything, no more leaks but now my GAS engine sounds like a school bus. I've lost power, going up hill is rough, once i hit 40mph my car starts to shake a little bit but when I am on a straight away it will sometimes drive normal and sometimes go back to driving slowly. it also idles rough.
View 14 RepliesFord Super Duty (1999-2016) :: 2005 - Idles Rough - Lacks Power?
I have a 2005 f250 with a 5.4 3v. I bought the truck with a cracked passenger side exhaust manifold about a year ago. We'll here recently the crack got worse and was giving the code P0171, so I had a shop replace it. I picked the truck up and not even a mile down the road it started idling terrible at lights and had very poor acceleration. And it gave me P0174 this time. It's only gotten worse now it's reading P0172, P0174,P0161, and P1489. I've replaced the spark plugs, MAF sensor, both vct solenoid, an the upstream o2 sensor on the passenger side. I also know I don't have any intake or vacuum leaks, I've had a shop check and so have I. It's starting to get expensive just replacing stuff. So, maybe I have a clogged catalytic converter ?
View 8 RepliesFord Super Duty (1999-2016) :: 2005 - Rough Idle / Loss Of Power Under 1k RPM
2005 250 5-speed total oil pressure loss ... At 110k mechanic diagnosed failing phasers from noise, rough idle, loss of power under 1k rpm. (Crew cab long box xl bought new for $25k)(first 100k were from carpenters (hard miles) so this truck is barebones and usefulness is much higher than cash value). Truck has 146k
All symptoms typically disappear over 1k rpm so I have limited idle time and manipulated engine speed to try and maintain 1000-1200 and all has been well for past 36k miles. Today noise (valve clatter?) persisted at all rpm and during a scramble to get off the highway all oil pressure was lost (I'm aware that pressure gauge on dash is not 100% reliable). After total pressure loss I cut engine and called tow truck. Out of curiosity, I actuated ignition and motor cranked maybe two rotations, and then appeared seized. After about 45 min waiting for tow I went back to disengage 4wd and take my rifles and skis out of truck. At this time I actuated ignition again and engine fired and ran as it had for past 36k miles. I drove about one mile constantly watching oil pressure gauge, then noise returned followed by instant drop from normal to 0 pressure (dash gauge) I immediately shut of engine.
I am a mechanical engineer, but not a mechanic. I am familiar with the cam phaser system and I understand that their operation is directly related to oil pressure. Today's temp was under 0'F. I have a very skilled mechanic who works for around 30-40% of cost of licensed shop and I know his skills to be on par.
Ford Super Duty (1999-2016) :: Idles Really Rough When Its Cold / No Power For About 10 Minutes
Need this software that would be willing to run a diagnostic on my truck? I replaced all the glow plugs a year ago and the relay a month ago. It idles really rough when it's cold (first start of the day with outside temps even at 90 degrees). It has no power for about 10 minutes. Sounds like an old John Deere 2 cylinder tractor for a few minutes. I have 370K miles on it. After it warms up it runs good. Plugging it in doesn't make a difference. There is no smoke while it is warming up. I have noticed when I accelerate quickly, it blows black smoke (not heavy but when following it you see and smell it).
View 4 RepliesFord Super Duty (1999-2016) :: 2002 F350 7.3L - Rough Idle / Knocking / Loss Of Power
Alright, I have a 2002 f350 7.3 4x4 ext cab xlt with 300k miles. Bought in may 2016 with 260k miles and towards November started running rough and felt like a loss of power. Had a no start but a new gray cps fixed that issue. Running fine. About a week later started it up and it had a rough idle, felt like not all cylinders/injectors were working. Was "knocking" and a loss of power. I was in the army at the time and stationed in Georgia, took it to a local diesel shop in Georgia and they confirmed my icp sensor was bad and injector #1 , #5 #7 were bad. Work was busy and money was scarce so I left it as it is and was saving up to buy the new parts. Then one day approx a week after the visit to the shop, I started the truck up and it ran fine. No misfire no knock no rough idle, drove fine for about a month.
In December, I was on vacation in florida to see my parents, drove the truck down, ran fine. While on vacation one day in a Walmart parking lot the truck didn't start up. Couldn't fix any issues then so towed the truck to my parents house. Did more troubleshoot, replaced fuel filter, cps, ipr valve, icp sensor, glow plugs, glow plug relay, ebpv pedestal was replaced with a ebpv delete pedestal. All parts bought oem and/or from riffraff diesel. Still would not start up. So then I bought a refurbished IDM from eBay, oem and then the truck finally started up one day but running rough again like it used to, then it wouldn't start again. So then, I replaced the PCM with a reflashed/refurbished one off eBay and boom truck started up, still running rough but now it starts up every time.
Now, took all eight injectors out and replaced all the o rings. Cleaned them up and put them back in, truck still running rough. Injectors didn't appear damaged nor the wiring harness so now I bought three reman injectors from riffraff. And replaced those three bad injectors. One of them is not spitting oil out the oil spout on the injector.
My dad has worked on freightliner semi trucks for years and is fairly knowledgeable when it comes to diesels. However he did something very amateurish the other day. So two injectors were installed while we were still waiting on the third in the mail. He wanted to see how the engine reacts when that one bad injector was not in play, but instead of unplugging the injector under the valve cover, he cut the wire outside the valve cover to the injector. He stated it's not a big deal and he can solder the wires back together. But once he cut the wire, the truck sounded a lot stronger, still rough idle but definitely stronger. Before, you would be pedal to the floor and the truck barely moves forward but now the truck will lunge forward. A big difference in power.
Now today, third injector came, swapped them out and fired up truck. We didn't solder the wire yet just quick connect, same you would use to connect wires for a car stereo. The new injector was not spitting oil out the oil spout. Even at high rev and truck warmed up. Truck still runs better with that one injector unplugged.
Tomorrow we will troubleshoot if somehow there's wires that grounding out or burnt out somewhere but as of right now everything seems to be in order, the uvch are tight, and no signs of anything burnt.
Triple checked everything, still getting fuel pressure, still getting oil pressure what gives? I also replaced the MAP sensor. Fuel pump is fine, fuel gets to fuel bowl. The next thing I'm thinking is maybe the hpop but we have oil pressure so idk..
Ford Super Duty (1999-2016) :: Stutter And Stalling Over 50 MPH When Hot
Turns out I have a loose injector head. The electrical body on top of the injector has separated from the bottom half of the injector. I do not know which injector it is or what side it is on. I know this is what happened because I found the head of the screw in my oil when I changed my oil for good measure and found the nut stuck to the oil plug.
2004.5 F250 SD XLT 4dr 6.0L
CAI, 4" Straight exhaust
EGR Delete, 6.4 Injector pump
Coolant filtration system.
New injectors al around
New ICP, New IPR, New Oil Cooler.
Recently Bulletproofed on ARP head studs, and the stock Head gasket,
New injector harness and FICM from DieselTech Ron
SCT tuner, running innovative diesel tunes. EGT Sensor
37x13.5r18 nitto trail grrappleers
No, I do not have a bad injector [Or I guess I do!!. This explains why it was testing ok. but still acting like a bad injector] , or a bad ICP. The Head is not leaking nor is the potentiometer [TPS] or CPS bad. All of these things have been replaced. Even the injector harness has been replaced. The only thing I have not done is remove the valve cover and making sure all the injectors are tight.
I recently had a contribution error on cylinder 8. Hence the extensive ends I went to above. The new harness and FICM connectors fixed that part of the problem, but apparently the bucking and stalling were not related to that.
No codes are coming up. I'm running an SCT tuner with Innovative Diesel's Extreme Street tune. 4" strait pipe, S&B CAI, 6.4l Injection pump, bulletproofed with ARP head studs, new oil cooler, egr delete, coolant filtration, EGT sensor, SCT tuner, etc etc. Everything but larger injectors. [was coming next]
The truck runs perfect, actually better than perfect after the harness, TPS repair, UNTIL I REACH OVER 60 MPH. At 60+ it starts bucking until i get below 45-50, then I can get back up to speed but no faster than 60. If I let off it real fast while bucking, it stalls.
Fuel PSI issue? The injection PSI isnt affected. Pulse width, normal.
I commute... [At 60 mph lately...] Sounds like I have a loose injector wire under the valve cover.
Ford Super Duty (1999-2016) :: 2006 F250 Running Rough / No Power On Acceleration / Code PO420?
CEL came on last night, OBD code PO420, truck is an 06 f250,5.4? Btw, truck running rough, no power on acceleration, in gear at idle, runs rough....
View 4 RepliesFord Super Duty (1999-2016) :: Stalling Under Load / Intermittent
My current truck is an early 99 F250, 7.3L diesel, CC 4x4(manual shift transaxle) auto transmission. It is basically stock, with the exception of a hutch/harpoon and a new fuel pump over the winter, an AIS intake. I have a magnaflow exhaust kit in the garage along with bellowed up pipes but have not installed them yet.
Here is my issue. Several times over the last 2 years, the truck will pull a load, or long trip, and with complete randomness, the engine will feel like it has shut off, there is usually a jerk or two, and the truck "restarts" itself and continues on like nothing happened. Last year we drove 1.5 hrs from home with the boat in tow, driving up Snoqualmie pass, and it died completely, no restart. We had to be towed home. It started right up at the shop, so no real clue of what happened.
When this happened, I had the fuel system checked for pressure and replaced the engine fuel filter, and all was good. I also had the Cam position sensor replaced/updated to the new grey sensor. Shortly after, I had the minor jerk/stall occur again, so I replaced the fuel pump and did the hutch/harpoon mod to ensure there wasn't an intermittent fuel pressure loss and that the in tank filters were not clogged.
Last weekend, i pulled my boat to Oregon, and the same "hiccup" happened as I was about 1.5 hrs into my trip. it was fine after that the rest of the 4 hr trip. We also drove back the same route and had no problems.
Ford Super Duty (1999-2016) :: Rumble When Starting And Idling
I was wondering if there is a aftermarket product to give my truck a more Rumble when starting and idling.
View 8 Replies