Ford Super Duty (1999-2016) :: Auto Shifter Lever Extremely Loose / Will Not Go Into Park At All
1999 F-350 . My shifter lever is extremely loose, it will not go into park at all. I tightened the two torx bolts, adjusted the needle but its still bad. Im thinking the cable is loose, I saw that there is a small rod attached to the end. Is there a way to tighten it or do I need a new cable assy.?
View 5 RepliesFord Super Duty (1999-2016) :: Hard To Start - Shifter On The Column Seemed To Have Some Play When In Gear
I started having a issue with getting my 00 f250 power stroke to start. It started out I could move around the gear shifter in park and get it start and today I had several times I had to put it in neutral to get it to crank. I did notice that my shifter on the column seemed to have some play when in gear but then again my 99 F250 V10 also has some free movement when in gear. Is there a neutral safety switch I could replace or any way to adjust the shifter?
View 14 RepliesFord Super Duty (1999-2016) :: 2003 F350 - Gear Shifter Very Tight And Hard To Pull Down
I'm looking at purchasing a 2003 F-350 from a Ford Dealer, Drove the Vehicle last night and the Gear shiftier was very tight and hard to pull down. Is this a real concern? The Sales guys said its better to be stiff rather than sloppy. But they will say anything, right. The vehicle is a deal and so I'm looking to find out why.
View 1 RepliesFord Super Duty (1999-2016) :: F250 Won't Go Into Park Gear
I have an issue with a truck I just bought. Sometimes, it doesn't go to Park when I shut it down. In order to start it I have to sometimes put it in neutral. Once in a while it will start when in the Park gear. What I should look into to fix it? It doesn't seem like a big deal.
View 6 RepliesFord Super Duty (1999-2016) :: Whine Or Squeal When Sit Idling In Gear Or Park
I have a 2013 f350 with the 6.2L gas and automatic transmission...when it sits idling in gear or park it starts to whine or squeal for about 30 seconds then stops and starts again. it makes a horrible sound if you shut the truck off while it's making the noise... Ford has had the truck for 5 weeks and checked the motor for vacuum leaks and changed the torque converter...but it's still doing it but less frequently now but according to them it's louder. I have a video but don't know how to upload it. if you go to YouTube and search ford raptor whine it shows a raptor making the same noise also.
View 7 RepliesFord Super Duty (1999-2016) :: 2006 - ZF6 Shifter Adjustment - Bent To Right?
I've put about 500 miles on my new to me 06 F250 4x4, CC, SB, V-10. One thing that is slightly annoying is the shifter position in R, L, 1 and 2. Shifter is against my knee in those positions. Re bent the shifter to place the more to the right? I have buckets with a console so I don't need to worry about a center passenger's legs. I have plenty of benders and metal working tools at my disposal, just asking for some guidance.
View 2 RepliesFord Super Duty (1999-2016) :: New Shifter Tube Now Key Won't Come Out And Steering Wheel Not Locking
Today I put a new shifter tube in a 02 f450. Everything works well, but the key won't come out and the steering wheel won't lock. Was told there is a button to push by the turn signal side but don't see any. Looked around top and bottom of column and didn't see anything out of place. Also found a black wire with a pink strip not connected to anything. Touched the wire to the column and key dinger sounded. Where should this wire be connected?
View 10 RepliesFord Super Duty (1999-2016) :: 2015 - Delay In Transmission To Engage When Start And Put Shifter In D
2015 F-250 4X4 CC gas truck. 6R140 Transmission..
My truck has 6500 miles on it and since day one when I put my shifter in (D) there is a 3-4 sec delay in the transmission to engage every morning when I start out, rest of the time there is no delay even when the truck sits all day at work (about 9 hours). I have read in 2011 (?) that the transmission was loosening it's prime and would cause this problem, so how it's got me thinking.
Ford Super Duty (1999-2016) :: 2002 - New Shifter Tube - Key Won't Come Out - Steering Wheel Won't Lock?
Today I put a new shifter tube in a 02 f450. Everything works well, but the key won't come out and the steering wheel won't lock. Was told there is a button to push by the turn signal side but don't see any. Looked around top and bottom of column and didn't see anything out of place. Also found a black wire with a pink strip not connected to anything. Touched the wire to the column and key dinger sounded. Where should this wire be connected?
View 14 RepliesFord Super Duty (1999-2016) :: When Taking Off Truck Will Not Shift Into OD Unless Cycle The Button On Shifter
I am having a bit of an issue with my new to me 2002 F350 V10 Ford, I have noticed a few times in the when taking off (first time after being parked)the truck will not shift into over drive unless I cycle the button on the shifter, after that the OD seems to work fine for the rest of the trip. Second thing I noticed is the "OD" light on the end of the shifter will come on at times (indicating the OD is off) even when the truck is in over drive, wiggling the shifter makes the light go out and the truck will not change gears. Would a new gear shifter fix this as it is a bit sloppy?
View 3 RepliesFord Super Duty (1999-2016) :: No Startup / Won't Even Turn Over
My F-350 has developed a new problem. It wont start. It wont even turn over. All Electricity is on, glow plugs glow, gauges work, lights work, but when you turn the key to the start position noting happens. Some of the indicators go dark.
I even tried a jump thinking my batteries no longer handle the load. Same results. I suppose I can remove the batteries and take them in for testing. In fact, I'll probably do that now.
2002 F-350 Superduty, 7.3 Ltr, Turbocharged. 260000+ miles.
Ford Super Duty (1999-2016) :: 2001 - Reverse Light Switch Only Works With Shifter Hold Up?
I have an 01 f350, my reverse lights only work when I hold up my shifter, like its almost into park. I think my reverse light switch is bad, but I don't know where its located.
View 6 RepliesFord Super Duty (1999-2016) :: 2002 F350 - Auto Shifter Starting To Get Some Play In It / Loose
2002 F350 5.4 . I did some plowing today, truck ran Great, but noticed the Auto Shifter starting to get some play in it, 185 k on it. I recall reading about how to tighten it back up.
View 3 RepliesFord Super Duty (1999-2016) :: Clicking Noise At Startup?
I have a 99 F-250 SD 4X4 7.3 with about 160,000 miles and still running strong. I haven't been able to troubleshoot a strange clicking noise during the Glow plug / pre start warm-up process. It seems like the noise is coming from a vacuum "relay/ actuator" ( I think that's what the part is) under the hood on the passenger's side. But again I am not a Ford mechanic, nor have I owned this complex of a truck before.
There seem to be two different vacuum terminals that both have two outlets that attach to vacuum hosing. The unit does not have a line ( or 2 ) connected to the innermost vacuum outlet. Does this need to be connected? If I put my fingers on the units outlets to restrict the noise becomes more high-pitched, then will cease to make the clicking sound sooner than if I didn't cover the outlets.
I'm unsure on the process on how to insert a photo. it's asking for a URL, does this mean I need a flickr photo account to transfer the photo? Can I just upload a JPG?
Ford Super Duty (1999-2016) :: 2003 F350 Sounds Like Shifter Motor On Transfer Case Is Trying To Engage
Truck is an 03 F350 with the 6.0. It sometimes sounds like the shift motor on the transfer case is trying to engage. It has the vacuum system which is blocked off. Warn aftermarket hubs. Switch on the dash with 2wd, 4wd and 4 low.
It's kind of an off and on thing. Try to engage for a few or more seconds then nothing for awhile then repeat. It sounds like it's at the transfer case. It could very well be coming from firewall/engine bay area as well. Is there anything between the dash switch and the motor?
Ford Super Duty (1999-2016) :: F350 Will Not Go In Park
I have a 99 F350 with a 7.3 diesel that will not shift into park.
View 10 RepliesFord Super Duty (1999-2016) :: 2011 XLT - Rear End Clunk On Startup
The last couple of weeks a new clunk has appeared on my F350, 6.2 CC LB FX4. If I've been parked for a while, when I drive off, within the first 30 yards or so there's a clunk. Seems worse when I've turned sharply out of a parking spot. Sounds like the rear diff or drivetrain... I have a locking rear diff. Is this engaged or disengaged while "at rest"? Could it be that its slow to unlock when I start?
View 13 RepliesFord Super Duty (1999-2016) :: Raps Or Knocks For A Second Or Two Immediately After Startup
I just picked up my first truck ever yesterday, a 2012 F250 crew 4x4 with the 6.2L gas engine. It seems to me, when the engine is cold, that it raps or knocks for a second or two immediately after startup...is this characteristic? The truck is a 'new-leftover' model with about 28 miles on it so far. When warm, or even semi-warm, the engine starts right up and sounds like a healthy american V8.
View 14 RepliesFord Super Duty (1999-2016) :: 2008 - Gray Smoke On Startup?
A little background. I bought the 2008 F250 XL, 5.4L with 145,000 miles in December. It had a bad engine (dropped valve). I had the engine replaced with a remanufactured one (Performance Products) and started driving it this month. To date, I have put about 700 miles on it with an oil/filter change at 500.
So, here is the newest problem. Yesterday I finished changing my body mount bushings (with Daystar polyurethane ones) and went for a test drive. When I started the engine, a smoke cloud caught my eye. I took a closer look and noticed it was a gray smoke. I jumped out and ran around to smell the smoke - it had a gas smell. I did not test for smoke after my test drive.
So here is my question. It is obviously burning excess fuel on startup. That would mean that one or more injectors are leaking down after shutdown, correct? Testing this would be done by performing a leakdown test? How do I go about doing this WITHOUT any special equipment?