Ford Super Duty (1999-2016) :: Front Drive Shaft Spinning While In 2 Wheel Drive
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesFord Super Duty (1999-2016) :: Front Drive Shaft Broken?
Not sure what caused it to break but my front driveshaft split in half. I had it in 4wd and was doing a K turn to back in my driveway in a snow storm.
I got underneath in the snow (miserable) and wasn't able to come close to getting it off. The bolts holding the shaft onto the t-case will not budge and the tiny 5/16" bolts stripped all my small 1/4" sockets. I'm guessing I need a 3/8" drive 5/16" for front and the rear just spins. Any tricks to getting this off the truck.
Ford Super Duty (1999-2016) :: Front Drive Shaft Angle After Lift
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
Ford Super Duty (1999-2016) :: 2004 - F350 Front Drive Shaft Metallic Squeal
I have a 2004 F350 Crew Cab DRW 4WD 6.0L.
The front drive shaft is making a high pitched metallic squeal while the truck is in motion. I thought it might be the universal joints but after lubricating the joints, I can still hear the squeal and it sounds like it is coming from inside the drive shaft. I also hear this squeal when I spin the drive shaft by hand.
I have quite a few questions about these drive shafts:
- What would cause a squeal from within the drive shaft?
- Are there any replaceable parts or do I have to get a new drive shaft?
- How do I identify the correct drive shaft part for my truck? Seems like there are a LOT of different models on the web.
- Are any of the aftermarket drive shafts any good? Any to avoid?
- Is this a DIY job or will I need to take it in to the shop?
Ford Super Duty (1999-2016) :: 2000 F350 - How To Correctly Install Front Drive Shaft
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 RepliesFord Super Duty (1999-2016) :: When To Replace Catalytic Converter?
ill be replacing my muffler here soon, its rusted out blows smoke out all the rust holes, and so on. gonna replace with a nice flo master. Question is, when is it time to replace the catalytic converter? 15 years old and 93000 miles, it still seems like its in good shape, but could it be getting clogged? just from the sounds of the exhaust the past few months, it almost sounds like the truck is somewhat congested. The power from the engine is kinda week, but that's the engine itself. I have no real problems getting up to speed. my hesitation issues from before turned out to be water in the gas tank. Figured since im down there does it make sense just to bite the bullet and throw a new catalytic converter on?
View 8 RepliesFord Super Duty (1999-2016) :: 2004 - Rear Drive Shaft Broken?
I have a 2004 F350 with a broken drive shaft.
Got the original shaft off and it has the following part number (2C34-4K145-DNA)
but I've since learned that the part number has changed but the only info I could get was 2???. 4R602DQA.
Trying to find the part number so I can find it under 750.00 from the dealer
Ford Super Duty (1999-2016) :: Vibration Starting At 60 MPH / Drive Shaft Balance
I have a vibration starting at 60mph. Its slight but there. I crawled under and found a very shiny rectangle of metal. Safe to assume I flung a shaft weight? It drives perfect around town just at freeway speeds.
View 14 RepliesFord Super Duty (1999-2016) :: 2007 F250 - Drive Shaft Installation
My elderly neighbor has asked me to re-attach his drive shaft on his F250.
Said his wife was driving and it broke the u joint or something, and he has gotten it repaired and wondered if I could put it back on. Has been sitting for a bit from what he said.
Just need to know, how I should clean up and or grease? the end with the boot on it. before I put it together. The boot looks to be zap strapped, is that standard?
Ford Super Duty (1999-2016) :: 2014 F250 - Squeak Coming From Drive Shaft Area
I have a 2014 4WD Super Duty. It has a squeak that is coming from the drive shaft area. I had someone listen to it as I drove slowly next to them. It is a repetitive: squeak squeak squeak squeak squeak. Not loud. The frequency increases as speed increases. I could believe it may be a U joint based on the frequency, but seems hard to believe with a new truck. I heard this sound when I first got it, but the sound was so slight that I thought it was just some sound associated with a newer engine. But now it is becoming a bit louder.
View 4 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Drive Shaft Removal To Grease The Center Spline
I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 RepliesFord Super Duty (1999-2016) :: Leak In Front Axle Shaft
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 2 RepliesFord Super Duty (1999-2016) :: Front Axle Shaft Wiggle
So the other day I took my locking hubs out and cleaned them really good. When they were out I noticed I could grabs axle shafts inside the hub and wiggle them quiet a bit. Is that normal?
View 2 RepliesFord Super Duty (1999-2016) :: F250 - Leak In Front Axle Shaft
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesFord Super Duty (1999-2016) :: Terrible Noise When Hit A Bump / Front Axle Shaft Removal
I have a E99 F350 7.3L 4x4 I know some or most of you have already probably replaced this part and or pulled a front axle shaft out. So here is my question...In the pictures provided you can see what I think everyone is calling a "Dust Seal" and as you can see it is bad and making a very terrible noise when i hit a bump...I was wondering what parts I would need to replace this seal? I tried looking it up and just get lost in all of the other things....I have found write-ups for the axle being removed while changing ball joints but none by it self to just replace this seal.
[URL] ....
Ford Super Duty (1999-2016) :: 2007 - Replacing Ball Joints - Front Axle Shaft Removal?
I am replacing the ball joints on my 07 f250 4x4. got down to the removal of the shaft itself and it won't budge. What is the secret here. Have to go to work on monday, and the weather in Cleveland isn't going to be very good on Sunday.
View 10 RepliesFord Super Duty (1999-2016) :: Front End Hop When Only Turning Right In 4 Wheel Drive
1. Why does my front end hop when only turning right in 4 wheel drive?
2. O nly one of my back tires spin, so does that mean that when I put it in 4 wheel drive I only have 3 tires spinning?
oh I got a 2001 xl 5.4 f250 and is this normal
Ford Super Duty (1999-2016) :: 2002 F250 Randomly Dies While Driving When Hits Bumps And Won't Start Immediately
My 2002 F250 7.3 randomly dies while driving and seems to only be when I hit a bump no matter the size. I have checked the valve cover harness connector outside of the valve covers and they look fine. I checked the ECM connection took it off and reconnected it.
Changed the CPS censor twice, checked the ICP sensor, checked continuity of all the glow plugs through the valve cover harness. Checked the fuel pump, checked all related fuses, changed the fuel filter, checked glow plug relay, batteries hold good voltage and were recently upgraded to bigger batteries.
Engine runs just a little rough but not enough to be of concern. Air filter is clean and oil level is perfect. What could possible be causing my truck to randomly die when it hits a bump and not start back right away??? This truck is new to me and its the first diesel engine I have ever owned.
Ford Super Duty (1999-2016) :: 2006 F350 - Rattling Sound When Engaged In Front Wheel Drive
This must have been asked before but I couldn't find any thread about it. Have a 2006 F350 that makes a rattling sound when engaged in front wheel drive. Sounds a bit like a loose ball from a ball bearing (or a small stone) rolling around. What might be causing this?
View 3 Replies