Ford Super Duty (1999-2016) :: 2011 F250 - Clunk Noise When Going Over Bumps
When I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
Ford Super Duty (1999-2016) :: 2000 F250 - Clunking Noise When Turning
I have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
Ford Super Duty (1999-2016) :: 2003 F250 - Thumping Noise While Turning Sounds Like U-joints?
I have a 2003 f250 superduty v-10 -- 4x4 -- when turning with 4wheel drive disengaged I have consistent thumping sound coming from front end -- more so when turning to left but still prevalent on right turns -- I put new hubs in due to the grinding noise when driving slow to mid speeds -- like axles not totally disengaging and grinding on teeth. but this is a secondary noise -- replaced left front axle with dorman unit -- tried to replace u joints on oe axle but rusted so badly couldn't get c clips to separate from ujoints --
this one is kicking my butt and making me look like a novice -- don't think it is ball joints or anything suspension related but I could be wrong -- sounds like thump thump thump as turning in slightly tight circle or going around corner in the parking lot.
Ford Super Duty (1999-2016) :: 2014 F250 - Clunk While Changing From P To D
Just moved into the 250 from years of 150's. Now have 98 miles and read that the tran would have noise but normal while breaking in.
whats normal, not used to this much Clunk while changing from P to D ect. More noise than used too I guess.
3.73 gears
2014 F250, 6.2 gas 2wd....
Ford Super Duty (1999-2016) :: 2006 F250 - Clunk When Come To A Complete Stop
Have an 06 F250. When I slow down to make a turn then accelerate it's like the drive shaft spins half a turn before it catches. Been doing it for awhile now. Now I'm get a clunk when I come to a complete stop. When you stop then truck settles there is a little clunk. Does this sound like the slip yoke problem?
View 1 RepliesFord Super Duty (1999-2016) :: 2005 F250 4wd - Clunk Under The Driver Seat
I have a 2005 f250 that has a wander and a clunk what feels like under the drivers seat. The driver side bushing in the radius arm has no dirt and looks like wear on it compared to the passenger side which is completely covered in dirt. My question is, bushing wear out will cause wander and a clunk. Is it hard to replace?
View 3 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Clunk In Front / Leaf Springs Bad?
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
Ford Super Duty (1999-2016) :: 2008 F250 - Squeak And Clunk / Bearings Are Loose
My rear wheel bearing are a little loose. This afternoon while diagnosing a squeak in the back I found this. While pushing the truck side to side there is a clunk and when you lay your hand on the tire you can feel it, bearings are loose. Nothing during the operation of the truck to give this away, truck runs and drives as it should but I need to check it our before something does go wrong. What I'm looking for is a torque / preload that the rear wheel bearings need to be set at.
View 2 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Clunk In Reverse When Clutch Is Pressed
My issue, just purchased f250, 2004, v 10, manual transmission, state vehicle with 32,000 miles but was a plow vehicle for localRMV lot, that said, great shape and runs strong but I get a clunk and shutter when I am in reverse and only when I push down clutch before stopping. Doesn't do it starting forward or reverse, only reverse and when I push clutch in before stopping. Did have a friend drive and looks like the transfer case is moving, as if mounts or bolts are loose. Does this make sense and could bad slip joints be putting excess torque on ?!?!?
View 4 RepliesFord Super Duty (1999-2016) :: F250 6.8 V10 Not Turning Over
Ok i have a 99 f250 with a 6.8 v10 that is not turning over at all. I have checked the battery and its good. I have replaced the starter and the starter relay and have tested the starter and its good too. I have also used a volt meter on the batter, starter, and relay and looked at the relevant info and they are all in the correct volt range. I have also taken the starter off and looked at the flywheel and it has good teeth so thats not an issue. I am completely stumped now as to what it could be?
View 5 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Clunk In Front End / Felt In The Floor And Steering Wheel
I have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 RepliesFord Super Duty (1999-2016) :: 2007 F250 - Front Wheel Clunk When Turn Sharply In Either Direction
2007 F250 4WD 5.4l ... when I turn sharply in either direction I am getting a light clunk sound similar to when you are in 4WD on blacktop and try turning. The engine also seems to wanna stall when I cut the wheel too sharp.
View 4 RepliesFord Super Duty (1999-2016) :: Super Loud Clunk Noise Come From The Door When Car Turned On
So the other day i opened the door and heard a super loud clunk noise come from the door and when I turned the car on and pulled hte window down it wouldn't go down all the way, only about 75% of the way so I assumed like BMW cars the window motor died but oddly it continued to go up and down just now 100% down.
Then 3 days later when I came to drive the car again the window went down to the 75% mark and now its jammed there with no movement even if I tried to lift the window up myself. Usually a broken motor allows this to happen but since it isn't budging I am wondering if its an electrical issue with the power window button more than the motor?
I say this because when i try to lower the passenger window from the driver side it works than out of no where on the 3rd time it wont move at all than 5 minutes later it will move or if it doesn't move I just go and pull the window down from the passenger side then I come to the driver side and try it and it works again than it'll stop again. So maybe its the power window control buttons on the drivers side that's failing?
Ford Super Duty (1999-2016) :: F250 V10 Dead Upon Turning Key To Start
My trouble is upon turning key to start everything goes dead (no power to anything). Does not always happen, sometimes she starts just fine.
After the power cut out if I turn key off, wait a minute, then back to on position she will sometimes come back as normal or sometimes the on "ding" will chatter and dash lights will be dim.
I have checked batt connections, starter/solenoid connections, block ground connection. All seems fine. Get same problem when I jump starter with screwdriver. Been suggested to me ignition switch to blame.
Ford Super Duty (1999-2016) :: 2002 F250 - Headlights Keep Turning Off
I have a 2002 ford f250 superduty and when I have my headlight switch set to auto to come on when it gets dark they will for awhile and then my headlights will turn off for no reason.
View 2 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Wipers Not Turning Off?
My 01 F-250's wipers would not shut off. As soon as the key was turned on they would come on. No delay but high and low only. Had to pull the fuse to drive it. I replaced the multi function switch as well as the relay with no fix. I did some reading on this problem and it is related to the "park" switch in the wiper motor itself. I took the black plastic cover off the motor which reveals the worm gear driving the plastic gear which acts as the switch.
The contacts for this switch are hard to get to as they are on the backside. I blew compressed air into every little crevice and removed most of the grease. I regreased and put it back together. Sure enough the wipers work just fine now. I am assuming the compressed air trick may be only temporary. Need to reveal the contacts for the park motor switch without destroying the plastic housing?
Ford Super Duty (1999-2016) :: 2003 F250 - Front End Clunking When Turning
Have an 03 f250 6.0L and the tie rod from pitman arm moves easily and there isn't a steering stabilizer, noise got worse after I put new tires on front but it's a loud clunk that I can feel. I've replaced the sway bar bushings and end links. Would the worn tired rod make that noise or would it be ball joints?
View 1 RepliesFord Super Duty (1999-2016) :: F250 - Strange Sound While Turning At Speed?
I have a '16 F250 4wd with the 6.7 and approx 3k miles. There has been a strange sound coming from the front end when turning left from a stoplight. It sounds like something slides or shifts and it only happens once in a while. The noise isn't loud but you can feel it.
View 2 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Steering Column Not Turning?
I have a 2002 F250 diesel, the key will turn to acc. but not on. It feels like it is hitting something in the column. I tried moving the shifting lever back and forth with my foot on the break, as I turned the key but it would not turn. I am thinking the tumblers are OK because it goes into acc. It feels like their is some lever that is not releasing the shift lever, because if I turn the key hard the shift lever jumps. What is wrong, or how the interface between the lock tumbler and the shift lever works?
View 4 Replies