Ford Super Duty (1999-2016) :: 2005 - Oil Leak From Front Axle?

I have an F250 4.2 diesel 4x4 double cab. Its a2005 model. I noticed an oil leak from the front left axle. It looks like its leaking from the axle tube. See pic attached. Is a seal probably worn? How big a job is this to fix.

View 4 Replies

Ford Super Duty (1999-2016) :: F250 - Leak In Front Axle Shaft

Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.

View 14 Replies

Ford Super Duty (1999-2016) :: 2012 F250 - Greasing Front Axle U-Joints

I noticed my '12 F250 has grease zerks on the front axle u-joints and was wondering how often you need to grease them ? My truck has 10k on it and while I was changing the oil tonight I decided to give them a few shots of grease until it started coming out of the joint.

View 12 Replies

Ford Super Duty (1999-2016) :: F250 - Front Axle Needle Bearing Replacement

I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.

View 10 Replies

Ford Super Duty (1999-2016) :: 2001 F250 - Rubbing Sound Near The Front Axle

I have a 2001 f250 7.3 4x4 today I locked the hubs, put it in 4 low and got threw some mud to go hunting fine. got back out of the woods and took it out of 4x4 unlocked hubs and went in reverse 30 yards.. Now when i drive it makes a weird sound like a rubbing sound near the front axle. What this is?

View 5 Replies

Ford 6.0L Power Stroke Diesel :: 2005 - Snap Ring Inside Front Hub?

What is the tool part number for a good pair of snap ring pliers that are heavy duty enough to remove the snap ring from inside an 05+ 4x4 front hub? I have broken two pairs of regular snap ring pliers attempting to remove it. The snap ring itself is roughly 1/8" thick and copper plated. It really wouldn't be that difficult to remove, but that collar on the spline that it has to pass over is thick too and it is whipping me something serious.

View 5 Replies

Ford Super Duty (1999-2016) :: 2013 F250 - Paint Peeling On Front Differential And Axle?

My 2013 f-250 with 6500mi. has peeling paint on the front differential and the axle.. I sprayed it with some fluid film for now.

View 14 Replies

Ford Super Duty (1999-2016) :: 2001 F250 - Frozen U-Joint In Driver Side Front Axle

I have a '01 F250 with a frozen u-joint in the driver side front axle. My question is can I put it together without the axle and drive it?

View 2 Replies

Ford Super Duty (1999-2016) :: 2000 F250 - Clunking Noise From Right Side Over Bumps - Front Axle Bearing

I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?

View 1 Replies

Ford Super Duty (1999-2016) :: 2005 F250 FX4 Swaying While Driving - Front End Leaking

My f250 felt like it had a flat as in it was "swaying" while I was driving today. as I'm pulling into my neighborhood it felt as if i had a flat. There is fluid leaking from what looks like a control arm or possibly a canister that's part of a vacuum system. I'm a carpenter obviously by my terminology used in this post. Its dark so ill take another look in the morning but what I'm talking about..

View 14 Replies

Ford Super Duty (1999-2016) :: 2005 F250 - Front Blinker Does Not Work When Fully Engaged

I have been having an issue with my blinker for the past few months. When the blinker is fully engaged, the right front blinker doesn't work. If I just push up on the blinker so it doesn't fully click into place, the right front blinker works fine, so it is not a burnt out bulb. I have also checked my blinker light in my mirrors and they work fine. Left blinker works fine. I am stumped on to what this can be and I need to get it inspected. 2005 F-250...

View 3 Replies

Ford Super Duty (1999-2016) :: F250 - How To Remove Axle Shaft

I have a 1999 F-250 super duty 7.3 4x4 and the rear drivers side axle seal is leaking. My question is how do I remove the axle shaft? my last truck a f150 had c clips in the diff that released the axle shaft but I did not see those on this truck. How to remove the axle shaft?

View 8 Replies

Ford Super Duty (1999-2016) :: Axle Swap 3.73 To 4.30 In A 2011 F250 6.2?

Love my '11 f250 SD 4WD CC SB. 6.2 with 3.73 e-locker. I've got 5 Star tunes in it, and the truck is a joy to drive empty, and tows my current 7k camper fine, though on steep inclines I wish I had the 4:30 gears.

Well, we just bought a bigger trailer, dry weight is an addtl 2400+ at 9400, so I'll need to do something.

I don't want a different truck, don't want (another trouble-prone) diesel. I think with 4:30s and the tune, I should be fine towing that trailer (with gear and passengers, probably 11-11.5k loaded). Not doing mountains here, just Michigan hills.

What's the best way to "do" a gear swap? I know if I buy a set of gears and a shop screws Em up, it's gonna whine/hum and still cost 2k to do (truck is 4wd)
I'm up in the boonies and finding a shop to swap the gears will be a problem. Getting Em done right will be even MORE trouble.

Can I just find 4:30 axles ans have them swapped (anything in t-case or sensors need to be touched?). I don't care if I lose the e-locker, I never use it.

View 14 Replies

Ford Super Duty (1999-2016) :: 2001 F250 - Axle Stuck In Differential

Finally finishing up my 2001 F250SD 4X4 project. Decided to pull down the front axle to replace the dust seals. I've got everything apart including the large knuckle seals. Tried to pull the passenger side axle out but it only moves about an inch to an inch and a half before it stops. Took off the differential cover to look for damage or something obvious but I don't see anything wrong. The axle is moving within the splines of the spider gear but that's it. Stumped and sitting on jacks!

View 14 Replies

Ford Super Duty (1999-2016) :: F250 - Using Jack Stand On Rear Axle

Just got done rotating my tires on my 16 F250 ccsb 4x4 and I used jack stands on my rear axle while I used the jack on the front axle. When I brought the truck down off the jack stands (first time using jack stands on this truck) I saw that they left little marks/divits on the rear axle. I had them between the wheel and the shock support and I can feel with my finger where the jack stand was supporting the truck. It doesn't seem anything major but I can surely point out to you exactly where the axle and the jack stand met. I'm sure this is a non issue but just wanted to check in here to make sure...

No trailer attached (of course!) And nothing in the bed with a full tank of gas...so basically just the weight of the truck...

View 12 Replies

Ford Super Duty (1999-2016) :: 2003 F250 - Knuckle / Axle Seal Replacement

Replacing the knuckle/axle seal due to my hub not holding a vacuum. I finally got the seal off the axle after several minutes of beating, but it finally came off. During the beating the metal shield that was in back of the seal took a beating as well and can not be reused. Is it really needed?

In this thread the pictures show that the shield was not installed after the seal was replaced. The shield does serve a purpose to keep crap out of the seal though.

View 8 Replies

Ford Super Duty (1999-2016) :: 2000 F250 - Axle Spins When Hubs Are Unlocked

I have a strange thing going on with my hubs i think. I have a 2000 f250 7.3 4x4 that I just purchased. Lettering on hubs were worn out as far as labeled locked or unlocked so I tried to turn the axel to see what position they were in. Drivers side spun freely but passenger side did not. Both hubs were counter clockwise and turning it to lock didn't change a thing.

Figured it was a bad hub so I jacked the front drivers side up. Spun tire with both hubs unlocked and axle didn't spin. Locked hub on drivers side and axle spun. Indicating the passenger side was unlocked. Then I locked passenger side and wheel would not turn. Ok. That seems right.

Jacked up passenger side front tire with drivers side on ground and axle spins no matter if its locked or unlocked. So does this indicate the hub is good and I should look at something else or could it still be the hub. Axle spins all the time and I don't want to wear anything out.

View 12 Replies

Ford Super Duty (1999-2016) :: F250 - Passenger Side Axle Won't Spin Freely

I have a 99 f250 7.3 4x4. The problem is in 2wd I can spin the front drive shaft freely and the driver side axle will turn but not passenger side. I've pulled both hubs off and both are in auto position and spin freely. Even with the hub off on the pass side the axle won't spin freely.

View 1 Replies

Ford Super Duty (1999-2016) :: 2015 - Front Axle Leaking A Lot?

I have a 2015 F250, cc 4X4 PSD. It has 22,000 miles on it. I notice a small quarter sized drop of oil after it is parked by the right side front wheel. It is coming from behind the dust cover and universal joint where the axle goes into the tube. I dont know how long it has been leaking. My issue is I am about 800 miles from home on a camping trip, have to go back to work Monday, and lcoal dealer here can't take it in till next week. So, if the hubs are not locked and the truck is in 2 wheel drive, the gears shouldn't be turning right? I assume it is ok to drive home. I didn't want to pull the plug and check the fluid because if any runs out and leaves a stain on the cover, I don't want ford trying to deny warranty claiming I messed with it first.

View 5 Replies