Ford Super Duty (1999-2016) :: 2003 F350 - Front Driver Side Wheel Bearing Went Out
I have a 2003 F350 srw 6.0. 4x4. Front driver side wheel bearing went out. Went to the auto parts store got a replacement. Got it all tore apart, put the new one on and the lockout didn't seem to fit right. Is there a difference in wheel bearing assemblies for electronic shift on the fly and regular lockout? I have the electronic shift on the fly lockouts and it had just a little bit of play in it when I put the snap ring back in.
View 3 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Front Wheel Bearing Noise
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
Ford Super Duty (1999-2016) :: 2004 F250 4WD - Front Wheel Bearing Replacement
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Clunking Noise From Right Side Over Bumps - Front Axle Bearing
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 RepliesFord Super Duty (1999-2016) :: 2000 F350 - Grinding From Front Axle When In Gear / Under Load
The issue is with my 2000 F350 crew longbed V10. Other than a BTS trans put in a little over a year ago, and FoMoCo motorsports headers, the whole truck is bone stock. Oh, it has that fantastic auto-hub thing with the fake locking hubs and the little switch on the dash (I'd love to convert it to a manual shifter...?). 174k on chassis, so things need to be done, 40k on engine, 3k on BTS 4r100.
Yesterday I was running around town, made a stop, and when I started moving again got a loud grinding from the front axle. Thought maybe I'd picked up a rock in a caliper or something, so I jumped out and checked everything, no joy. Moved forward, there it is again. No vibration, but loud enough (or telegraphing enough) to hear clearly in the cab. Let the truck roll forward, popped in to neutral, noise fades away. Back in to drive, there it is. So, now I know it's trans/t-case/driveshaft/related. I recently put new vacuum lines in, checked all the connections, and pulled, cleaned and lubed the hubs.
And since the trans is a nearly new BTS that is working just find, I'm narrowing the search to the hubs, drive shaft, t-case.
Get home (noise abates above 30mph, or everything else drowns it out), crawl under, and find the front driveshaft is locked. Ok, stuck hub? Pull out both the fake locking hubs, and now the shaft turns. I can turn each front axle by hand at the u-joint, and I kinda hear a faint grinding on the right side (will bad needles make noise only under a load from the trans and not coasting in neutral?), and when I swing the drive shaft around the left axle moves, right doesn't, etc etc.
I'm going to pull the drive shaft today and check the U joints, and drive a bit to see if the noise is still there, but I am thinking I might have some bad needles on the pax side axle...
Ford Super Duty (1999-2016) :: F350 - Grinding Noise On Left Side Front
I replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 RepliesFord Super Duty (1999-2016) :: 2011 F350 - Front End Noise / Kind Of Shudder?
Truck is 2011, F350, 4x4 CC Long box with a 6.2, 124,000 km on it. Was driving home last night towing my jet boat when I heard a sudden noise from the front end, kind of shudder, first reaction was a flat so headed to the curd. No flat, nothing running hot, no play in wheels, all looked good underneath the front end. Pulled out and drove away, got about 15 km and it happened again, looked all around nothing obvious so pulled out and drove home (25 km) no issue.
This morning wanted to investigate further. Drove truck down the block and heard a definite rotating type sound. Not a grinding more like a scrape sound. After a minute it went away. Went into a parking lot and drove in tight circles but no strange noise. Found that the auto locking hubs were not working but hub would lock in manual. No strange noises with hubs locked in either.
Jacked up truck rotate front wheels, no sound and no play or wiggle on either side. Pulled the hubs and the passenger side had water in it. Hub was not rusty but it didn't look as good as the other side. Not sure how water got there as I have never driven in water, although I am not original owner but have had it two years and put 25,000 km on it. Could the water have gone in deeper and caused a bearing to fail?
Ford Super Duty (1999-2016) :: 2001 F350 - Low Grind Like Noise Coming From The Right Front
I have a 2001 f350 4x4 with7.3 diesel...I have recently noticed a low grind like noise coming from the right front. I have troubled shot the issue and I am 100% sure it is the wheel hub assembly. Did I mention I am running 37x13.50 tires..and now you say no it is the hubs...and they are the original hubs. My question is every thing I look for shows ABS is on my truck... I look at the hub and don't see it.. so with the Dana 60 front does it have ABS or not? Also, should I go motorcraft, Timken or moog wheel hubs?
View 1 RepliesFord Super Duty (1999-2016) :: 2010 F350 - Transmission Makes A Weird Noise When Takeoff And Shift Into Gear
I bought this truck with 60,000 miles and have had about 3 months. I don't drive it very much but when I do I have noticed that when it sets for 4-5 days or longer the transmission makes a weird noise as you take off and does does shift into gear as it does when I use it ever day. The problem goes away very quickly (not even a 1/4 mile driving) and everything is fine after that. By the way I took it to the ford dealer who did a complete 60,000 mile service on it that was suppose to include changing the transmission fluid and filters-could they have screwed something up (I did not notice this issue until after the 60,000 mile service?).
View 7 RepliesFord Super Duty (1999-2016) :: 2002 - Vibration From Front Side - Spongy Brake Pedal - Front Hub Bearing?
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 RepliesFord Super Duty (1999-2016) :: 2004 - F350 Front Drive Shaft Metallic Squeal
I have a 2004 F350 Crew Cab DRW 4WD 6.0L.
The front drive shaft is making a high pitched metallic squeal while the truck is in motion. I thought it might be the universal joints but after lubricating the joints, I can still hear the squeal and it sounds like it is coming from inside the drive shaft. I also hear this squeal when I spin the drive shaft by hand.
I have quite a few questions about these drive shafts:
- What would cause a squeal from within the drive shaft?
- Are there any replaceable parts or do I have to get a new drive shaft?
- How do I identify the correct drive shaft part for my truck? Seems like there are a LOT of different models on the web.
- Are any of the aftermarket drive shafts any good? Any to avoid?
- Is this a DIY job or will I need to take it in to the shop?
Ford Super Duty (1999-2016) :: 2004 F350 - Bolt Hole Diameter On Front Shackles
I am getting ready to make a set of front shackles for my truck for a temporary lift solution to fit my 35s until i can afford a complete suspension lift kit. I cannot for the life of me find the size of the hole for the bolts. I don't wanna drill it too big then have play in the shackle. My stockers are still installed so I don't have those to measure just yet. Need to verify the diameter hole i need to drill? and stock shackles look to be about 5.25" center to center, from what i can measure with them installed on the truck? so 2" lift, the new shackles will need to be about 9.25" center to center, right? (add 4", nets a 2" lift?)
View 7 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Faint Grinding Noise In Left Front Wheel
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 RepliesFord Super Duty (1999-2016) :: F250 - Front Axle Needle Bearing Replacement
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Little Bit Of Movement In Front Wheel Bearing And Hub Assemblies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Front Wheel Bearing / Manual Hub Whining
Well, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
Ford Super Duty (1999-2016) :: 2009 F450 - Dry Ball Bearing Sound From Front Of Engine
I have 2009 F-450 6.4L Diesel with 41K miles and just started to have a noise that can be heard up in the CAB of the truck while driving or idling. It sounds like a dry ball bearing that would go bad in home computer AC power supply or CPU cooling fan. The sound starts when the engine is at full operating temperature and most noticeable and the loudest if you are standing in front of the engine at idle outside.
Checked all fluids and they are normal. Turning the steering wheel doesn't affect the sound either or turning off the AC. Check engine light has not come on. The only thing I have noticed is that clutch fan stays on a very long time after starting cold and takes about a mile or two before it disengages. The truck is only used to tow a 36' 5th wheel and sits the majority of the time.
Ford Super Duty (1999-2016) :: 2003 F250 - Replace The Front Hub Wheel Bearing Assemblies?
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 RepliesFord Super Duty (1999-2016) :: 2004 F350 - Loud Clunk Noise In Forward Or Reverse Hi Or Lo When Accelerate
Ive got a 04 f350 that after u shift into 4hi or 4lo when u accelerate it it makes loud clunk noise in fwd or reverse hi or lo. With hubs unlocked it still clunks. Have checked, wheel bearings, axle U-joints, and driveshaft joints all good. So I am thinking I've got issues in t-case. Popped drain plug out and wow that dex merc 4 looks nasty. So thinking I need exploded view of transfer case.
View 4 Replies