Ford Super Duty (1999-2016) :: 2006 F350 - Code P2623 IPR Circuit Open
I have a 2006 F-350. I got a code p2623 ipr circuit open. I ordered a new one and currently waiting on it. I pulled the old one and the screen has been replaced already. How often do these valves go bad? Is there anything else I should check?
View 6 RepliesFord Super Duty (1999-2016) :: 2002 F350 - New Alternator Not Charging
2002 f350 super cab 7.3 diesel, replaced alternator because wasn't getting charge to batts, Napa guy checked batts and determined no charge, replaced alt, still no charge, have 12v at alt post with engine running or not. My ? is, is there a fuse in here somewhere that I'm missing? Went through all fuses in fuse panel all good.
View 7 RepliesFord Super Duty (1999-2016) :: 2002 F350 - Cylinders 4 And 6 High To Low Side Open
Alright, so here's what I've got: 2002 Ford F-350 7.3L - Unmodified, Stock, no chip, no tuner, 130K miles, been run with off-road diesel most of its life as a farm truck.
Here's what it's doing: Serious misfire in cylinders 4 and 6. At idle, mild miss. Throttle from 0 to 50 percent, runs well. Throttle from 50 percent to 100 percent, heavy miss, chugging, white smoke out the exhaust.
Here's what we've done so far:
New UVC Harnesses with updated pigtails.
Cleaned Fuel Filter Mixing screens.
Cleaned out fuel tank.
Cleaned bowl.
Changed Fuel Filter.
Changed IDMs
Changed Crank Sensor.
Inspected injectors while running to see if oil is pumping (it is).
No improvement. Where to go from here. Pulled codes, and it says Cylinder #4 and #6 High to Low Side open. We don't know what to do at this point.
Ford Super Duty (1999-2016) :: 2000 F250 - Code P1746 - EPC Solenoid / Open Circuit
I have a 4r100 in my 2000 f250 7.3. I am getting a P1746-EPC Solenoid, open circuit. Does this mean this particular solenoid in the solenoid body has failed and should i replace the solenoid body?
View 3 RepliesFord Super Duty (1999-2016) :: 2007 F350 Won't Start / Codes For All Eight Injectors Low Circuit
2007 F350 6.0 .. I let the truck sit for about a week went out to start it truck cranked right up then died now the truck wont start truck was running fine until this I wasn't having any starting problems. the codes are all eight injectors low circuit tested ficm had 48.3 volts...
View 1 RepliesFord Super Duty (1999-2016) :: 2000 F350 V10 Would Not Turn Over / Alternator Is Shot
My truck has been sitting for 3 years and I want to bring it back from retirement. I changed oil, checked fluids, replaced the starter, starter solenoid/relay and tossed in a 2 yr old charged battery (800CA). She would not turn over and I jumped with another vehicle. She turned right over and with an insane dust cloud! I went to disconnect jumped cables and it died. I assume the alternator is shot.
Jumped again to bring up to temp so I could check tranny fluid. It was running for about 5 minutes and just quit. Nothing mechanically to my knowledge caused this. It quit peacefully. I went to fire it back up and all I get is a click at relay on inner fender. The new one. Even while jumping..... What I should test/diagnose next.
Ford Super Duty (1999-2016) :: 2006 F350 Won't Start At All - Alternator Or Battery?
I went to start my 2006 F350 6.0 this morning. 20 degrees outside. It nearly turned over, then it appeared that the batteries would not support another start - a slowing of the pre-engine start revving....
So I let it sit a while, now it won't start at all. When I try to start it, the dashboard flashes, clicking sounds occur and even after pulling out the keys, the needles on the gauges shake for a few seconds.
Is this more a battery issue or an alternator issue?
Ford Super Duty (1999-2016) :: Code P0001 - Fuel Volume Regulator Control Circuit Open
My scanner reads P0001 Fuel Volume Regulator Control Circuit Open. My truck shuts down without warning, runs great otherwise. I've changed 2 grey CPS units and now have the Black IH one installed. What the Fuel Volume Reg.is? Is it the IPR on the HPOP?F250SD 7.3 225,000 miles.
View 10 RepliesFord Super Duty (1999-2016) :: F350 Starter Won't Crank?
I have a 1999 f350 7.3. Turn the key lights and fuel pump come on but the starter wont crank. I replaced the starter and checked all the fuses i could find. The only way i can get the truck to crank is by jumping the relay under the hood .
View 5 RepliesFord Super Duty (1999-2016) :: 2000 F350 - Batteries Draining Down / Alternator Seems To Be Running Really Hot
2000 f350 7.3 .. I'm having a horrible time trying to figure out why my truck is draining down the batteries. I can charge my batteries over night and put hem in and the truck will run for a few hours but then it dies completely. The alternator seems to be running really hot afterward like it is being over worked. I put in 2 different alternators and 2 new batteries and it didn't fix the issue.
I then put in a new starter relay. Still having the same issue. I believe I have a short because I tested for it but am unable to locate the short. I heard if you over work the bushings in the starter they can ground out on the casing which will cause something similar to this to happen. I work in ND and had to cold start it in - temperatures the morning this all began. I purchased a new starter but don't want to put it in if that is not the issue.
Ford Super Duty (1999-2016) :: 2002 F350 - Power Steering Has No Resistance
My 02 F350 steering lost all resistance. I can almost spin the steering wheel to each stop. What would cause that? Recent front brake rotor/caliper/pad replacement is the only thing the truck has had done since I've owned it. (2 months now). It's way too loose to be safe.
View 11 RepliesFord Super Duty (1999-2016) :: 2015 F350 - Starter Did Not Crank Over At All
2015 F350 6.2, 4 door 8' bed FX4...... 17,200 miles.
This morning when outside to start it (nice sunny morning) and turned the key and all the dash lights went on and also went crazy. Said it had all kind of problems on the dash, Trac system, Over heating and so on. The starter did not crank over at all. Tried this about 8 times in 45 minutes, no worky. Call Ford, they towed it to the dealer. I last drove it 2 days ago. All stock, no programmer.
Ford Super Duty (1999-2016) :: 2002 F350 - No Power / Speedometer And Tachometer Swinging Back And Forth
I have a 2002 F-350 with a 7.3 powerstroke. Last week, I replaced both my batteries. When I tried to start the truck, the electronics when a bit crazy. Speedometer and Tachometer swinging back and forth. Then when it did start it ran rough and after a minute it shut off. All electrical functions are completely dead. I finally unhooked the batteries and went in the house to cool off. When I came back, rehooked up the batteries, it started right up and everything acted normal. Everything was normal until last night, it started fine and was idling for about 5 minutes and it shut off. Absolutely, NO electrical power, even tried to jump start and still no electrical activity. Unhooked the batteries waited about 15 minutes, hooked them back up. It started just fine.
View 5 RepliesFord Super Duty (1999-2016) :: 2002 F350 7.3L - Rough Idle / Knocking / Loss Of Power
Alright, I have a 2002 f350 7.3 4x4 ext cab xlt with 300k miles. Bought in may 2016 with 260k miles and towards November started running rough and felt like a loss of power. Had a no start but a new gray cps fixed that issue. Running fine. About a week later started it up and it had a rough idle, felt like not all cylinders/injectors were working. Was "knocking" and a loss of power. I was in the army at the time and stationed in Georgia, took it to a local diesel shop in Georgia and they confirmed my icp sensor was bad and injector #1 , #5 #7 were bad. Work was busy and money was scarce so I left it as it is and was saving up to buy the new parts. Then one day approx a week after the visit to the shop, I started the truck up and it ran fine. No misfire no knock no rough idle, drove fine for about a month.
In December, I was on vacation in florida to see my parents, drove the truck down, ran fine. While on vacation one day in a Walmart parking lot the truck didn't start up. Couldn't fix any issues then so towed the truck to my parents house. Did more troubleshoot, replaced fuel filter, cps, ipr valve, icp sensor, glow plugs, glow plug relay, ebpv pedestal was replaced with a ebpv delete pedestal. All parts bought oem and/or from riffraff diesel. Still would not start up. So then I bought a refurbished IDM from eBay, oem and then the truck finally started up one day but running rough again like it used to, then it wouldn't start again. So then, I replaced the PCM with a reflashed/refurbished one off eBay and boom truck started up, still running rough but now it starts up every time.
Now, took all eight injectors out and replaced all the o rings. Cleaned them up and put them back in, truck still running rough. Injectors didn't appear damaged nor the wiring harness so now I bought three reman injectors from riffraff. And replaced those three bad injectors. One of them is not spitting oil out the oil spout on the injector.
My dad has worked on freightliner semi trucks for years and is fairly knowledgeable when it comes to diesels. However he did something very amateurish the other day. So two injectors were installed while we were still waiting on the third in the mail. He wanted to see how the engine reacts when that one bad injector was not in play, but instead of unplugging the injector under the valve cover, he cut the wire outside the valve cover to the injector. He stated it's not a big deal and he can solder the wires back together. But once he cut the wire, the truck sounded a lot stronger, still rough idle but definitely stronger. Before, you would be pedal to the floor and the truck barely moves forward but now the truck will lunge forward. A big difference in power.
Now today, third injector came, swapped them out and fired up truck. We didn't solder the wire yet just quick connect, same you would use to connect wires for a car stereo. The new injector was not spitting oil out the oil spout. Even at high rev and truck warmed up. Truck still runs better with that one injector unplugged.
Tomorrow we will troubleshoot if somehow there's wires that grounding out or burnt out somewhere but as of right now everything seems to be in order, the uvch are tight, and no signs of anything burnt.
Triple checked everything, still getting fuel pressure, still getting oil pressure what gives? I also replaced the MAP sensor. Fuel pump is fine, fuel gets to fuel bowl. The next thing I'm thinking is maybe the hpop but we have oil pressure so idk..
Ford Super Duty (1999-2016) :: 2006 F350 Not Starting - Code P2285 - Injector Control Pressure Sensor Circuit Low
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
Ford Super Duty (1999-2016) :: 2002 F350 - Popping Sound Coming From Exhaust And Lose Power
I have a 2002 F350 with the triton 5.4. For the last week it has been running like crap. I just did my plugs about a month ago. I don't know if it's a miss fire or bad fuel or I don't know what it could be. It's a popping sound coming from my exhaust and when it happens I lose power. It happens off and on. One second it will run fine and normal and the next runs bad. What it could be. Today I just changed my fuel filter and added STP octane boost and fuel injector cleaner. Haven't seen a difference yet.
View 4 RepliesFord Super Duty (1999-2016) :: 2002 F350 - Power Window Gauges And Ignition Buzzer Quit Working
The interior lights, radio, and power window gauges and the ignition buzzer on my 2002 F350 quit working. What could cause this? Everything else still works.
View 7 RepliesFord Super Duty (1999-2016) :: 2015 F350 - Cannot Open Lid On Center Arm Rest
I have a new 2015 F350 XLT. For the life of me I cannot open the lid on the center arm rest. I have read the manual, and I can't open the lid. This is my 5th Super Duty with the last being a 2010. So you would think this would be a no brainer. I can pull on the handle and its not opening. Pry the damn thing open? Is there a hidden lock? Hidden treasure?
View 14 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Turn Signal Malfunction Caused By Brake Light Circuit
I'm having a turn signal issue with my '02 F-250 that started this morning out of the blue. Seems that when the signal switch is set for a right hand turn and the brakes are applied, the signal will then become solid, not flash, and then blow the fuse. Evidently something with the brake light circuit is overloading the turn signal circuit and not canceling when the turn signal is activated.
Here are a couple of things I have tried to narrow down the culprit.
1) Left turn signal works fine regardless if the brake lights are operating.
2) Brake light circuit operates fine by itself.
3) Right turn signal works fine but there seems to be a back-feed of power causing the center third brake light as well as the left side rear brake light to flash in unison. If brake lights are then activated, the flash stops and becomes constant thus blowing the fuse.
4) Emergency Hazard lights work perfect but the center third brake light again flashes as well which reverts back to some type of back-feed of power. Also, if brake lights come on, flashing turns to constant light and then blows the fuse again.
I guess my question is,. does this seem like the multi-function switch needs replacing or could this be a relay issue of some sort? I don' think its a ground issue simply because the left turn signal circuit as well as the center brake light circuit are both being breached when the right turn signal is activated. Your thoughts?
2002 F-250 Super Duty 5.4 V8