Ford Super Duty (1999-2016) :: 2001 F250 - Slight Vibration When Started The Engine - Rough Shifting
The truck is in my Sig 01 F250 5.4
Just got back from a long trip with it. Parked it for 3 days, all was running fine. Went to dinner Sat night and all was great, left the restaurant and as soon as I started the engine I noticed a slight vibration. As soon as I hit 42 miles per hour, it started shaking pretty good. I pulled over and checked under the truck to make sure I did not have anything I was not supposed to hanging down.
Driveshaft looked good, nothing leaking from rear end or tranny. When it does vibrate, the Tach shows the unhappiness as well. This a.m. driving to work it was vibrating at all speeds and shifting was very rough, had a hard time deciding if it wanted to be in second or third gear. I don't think this is drive train issue... When it shutters and sputters at 40ish MPH, its almost like it loses power and I have to let off the gas. and then under power it shakes badly.
I had the super chip settings for performance tow when this started and then I changed it back to stock settings, thinking it might work, which it only got worse. Changing the settings with the Superchip you have to disable the fuel system and I do this by pulling the fuel pump fuse under the hood in the power distro box.
I think the ujoints are still good, the oil and tranny fluid are spot on. Hubs are locked but in 2WD. Had all the front end replaced 15K miles ago. Brand new tires and wheels in Sept, front end alignment done at same time, front brakes were 90% and rear brakes at 20%.
Ford Super Duty (1999-2016) :: 2011 F250 - Vibration Between 40 - 50 MPH
I have a 2011 f250 6.7 and I have a very bad vibration between 40-50 that seems to peak around 45-47. It also starts again at 80+ . the dealer told me they could not find a problem. Then another told me its normal. The tire shop around here told me the tires were shot so I bought new tires. No luck. It does not affect it if I change gears.
2011 f250 4x4 6.7 SWB. 140,000 miles
Ford Super Duty (1999-2016) :: 2003 F250 - Vibration Between 40 And 60 MPH
I have an '03 F250 Super Cab, 7.3L PSD, 4WD. I've started getting a large vibration between 40 and 60 mph. Started after driving on the PA highways towing a trailer with a car and hitting several deep pot holes.
I have had the wheels balanced, rotated, balanced a second time by a different shop and had them perform an alignment - Still No change.
The garage I took it to said the hubs were shot so I had them replaced - supposedly with Moog, lifetime warranty hubs. Still - No Change.
The tie rods and steering linkages are a year old, so unless something was damaged (visually, they look good, and feel tight) it probably isn't them.
I replaced the ball joints around 80,000 miles and now the truck has 155,000 miles. They appear to be ok, with maybe just a little movement in the Passenger side upper.
If there is any movement at all in the ball joint, will it cause a vibration?
I plan to rotate my full size spare through all 4 corners this weekend to eliminate the possibility of a bent rim.
I have another set of ball joints and seals on order which should arrive next week. Probably next weekend's project.
Ford Super Duty (1999-2016) :: F250 - Vibration Above 70 MPH - Speed Related
I have a 1999 F250 super duty with a mean vibration at 70+ mph. It is a 5.4L manual trans manual 4x4 extended cab short box with around 250k miles on the body and 50k on the motor. It is a one piece drive shaft with the double knuckle at the t- case. it has had a vibration in the drive line since i bought i about a year ago. there is almost zero vibration at 60 mph but at around 70 the vibration starts to get really bad. The vibration is speed related because when i push in the clutch or pull it out of gear the vibration is still there. i seems to vibrate more when winding out in 3rd and 4th gear but that may just be because off the exhaust resonating or something. I have already done u-joints, balanced the drive shaft, put brand new tires on mounted and balanced, replace transfer case output bearing and both front hub assemblies. the vibration feels like it is coming from the trans or transfer case. every thing i tried made very little impact on the vibration. I'm a loss and i don't know what else to try. i know the throw out bearing an pilot bushing are bad and the clutch is well worn so ill be replacing that soon but i don't believe that is causing the vibration.
View 7 RepliesFord Super Duty (1999-2016) :: 2006 F250 XLT - Vibration In The Floor At 70 MPH
I am new to the Superduty and the Diesel world. I just purchased a used 2006 F250 SD XLT with 79K miles on it. This truck has a brand new 6 inch rancho lift. I just bought brand new 35x12.50x18 toyo open country AT tires and new 18 inch rims. I have the steering box replaced, new brakes all the way around, front end alignment and the Turbo pedestal secured.
However, I am still getting a vibration in the floor going down the highway when i hit 70MPH under acceleration? Once I let off the gas the noise goes away.
Ford Super Duty (1999-2016) :: 2015 F250 - Vibration From Driveline
I have a 15 F250 CC SB 6.2 4x4 that is suffering from a driveline vibration. Had the shaft checked for balance and it was off. It's a little better now but still there. Checked all the angles and they're correct. Also came up with a curious observation that all CC SB 4x4's have a slip yoke driveshaft at the transfer case while all the other trucks have the fixed yoke. This appears to be my source of the vibration.
View 3 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Vibration When Letting Off Accelerator
So, I'm slowly but surely eliminating a terribly shaky front end on my 2002 F-250 7.3L 4x4. First was a new carrier joint on the front drive shaft. Didn't work much, but the shop said the darn thing was falling apart. Next thing I did was new wheel bearings and manual hubs. Less vibration for sure. But the last remaining issue, in terms of vibration, is that when I let go of the Accelerator going at any speed above 60 MPH, it makes a horrible horrible noise, and I could feel a vibration. It shakes the whole truck, but I can very noticeably feel it directly in the gas pedal. It's really only an issue during deceleration. What could it be??? Drive shaft U-joints? Torque Converter? Something else in the Front End? Something in the engine even?? I don't exactly have the funds to tackle every possible solution.
View 1 RepliesFord Super Duty (1999-2016) :: F250 - Driveline Vibration That Is Speed Dependent
I have a 1999 f250 SuperDuty with a nasty vibration That begins at about 70mph. The truck is an extended cab 5.4l Manual trans 4X4 with a one piece driveshaft (No mid bearing). The Vibration appears to me to be a driveline vibration that is speed dependent. It is the same in gear, out of gear clutch in or out. I have replaced the wheel bearings/hub assemblies on all four corners, completely rebuilt and balanced the driveshaft the driveshaft, removed the front driveshaft, put brand new tires mounted and balanced on all four corners, new clutch, had the flywheel turned and balanced, and replaced the transfer case output bearings. Pinion bearing feels tight and does not leak.
Also the Input in the trans felt tight when i had the trans out. The truck had the vibration when i bought the truck and still vibrates after i have done all of this work. i did not change the motor mounts because they looked fine. when i bought the truck the tabs on the extension housing holding the trans-mount to the trans were broken so i make a huge "exhaust clamp" to straddle the trans and bolt to the trans mount.
After driving the truck up north last weekend the truck seems to shake going taking of at lower rpm as if the motor mounts and trans mounts are bad. I guess my questions is can a bad trans mount, motor mounts cause this Vibration at highway speed. if so is there a way to fasten the trans-mount to the extension housing without replacing the extension housing. If not what else can cause this issue?
Ford Super Duty (1999-2016) :: 2003 F250 - Vibration Coming From Front?
I have a bad wobble/vibration coming from front end i think i replaced hub locking hubs u joints truck dont feel safe at all took it to ford they say its normal no way its not just starting doing it few month feels like the 4x4 is in use when hitting bumps when driving if you go slight left or right it seems too make act up more.
View 2 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Vibration At All Speeds And In Rear End When Braking
My 2003 Ford F250 V10 seems to have a vibration, sometimes at all speeds and sometimes at freeway speeds. I replaced front hub assemblies and ball joints and rear calipers last year. When braking i have a vibration in rear as well, which I think is from uneven rotor but can it be causing my vibration? Also sometimes I can smell hot brakes from the rear.
View 2 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Vibration Under Acceleration And When Maintaining Speed
Now that I use my truck as a daily driver I am noticing a vibration under acceleration at 30-35 and constant vibration at 45-50 accelerating or maintaining speed. I have replaced all three u-joints as well as new ribbed highway tires all around and still have the vibration. It seems worse in OD. I have done a little research and am either going to shim center support/machine a new one or have a one piece shaft made and need info on how to successfully gotten rid of this vibe on their truck mainly the amount of shimming required and the final driveline angle. It seems that most posts regarding this issue lean towards the fact that the 45-50mph vibe is normal for my year super duty and that's probably right but I want to remedy problem not "live with it!" (10 mile 45mph stretch to work @ 4AM, vibe bugs the heck out of me!)
Truck is 2000 f250 SC 2wd 4r100 3.73 gear currently 51000 miles.
Ford Super Duty (1999-2016) :: 2002 F250 - Roar And Vibration At Rear End While Driving Between 55 - 65 MPH
I have a 02' 250 4x4 with 250000 miles on it. While driving between 55 to 65 mph there is a roar and vibration that seems to be coming from the rear. I have about 35% tire tread left and have had the rear tires balanced and it still does it. Having issues with drive shafts unbalanced or rear ends?? I am not sure where to start....
View 1 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Vibration When Accelerating From A Stop And Under Load
My F250 6.4, 3.73 Crew Cab Short bed vibrates when accelerating from a stop with my 5th wheel on. The 5th wheel weighs 12K. It is a medium to high frequency vibration that is felt throughout the entire truck. It continues through the shift into 2nd (TorqueShift Tranny). The harder you accelerate the more you feel it.
It does not occur if truck is unloaded and you accelerate at full throttle. Is this normal or should I get it looked at?
Ford Super Duty (1999-2016) :: 2003 F250 - Vibration Under The Truck Near The Back When Accelerate
2003 f250 crewcab 6.0 auto 4x4. I all of a sudden started feeling a vibration under the truck near the back when I accelerate and when I let off the gas no other time. No noises or clanking just vibration. I can wiggle the driveshaft inside the carrier bearing do you think that could be it or is it the rear end.
View 14 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Front End Noise / Slight Vibration In The Floor
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
Ford Super Duty (1999-2016) :: 2012 F250 6.2L - Drone / Vibration When In Drive Between 1600 - 1800 RPMs
My 2012 F250 6.2L (Gas) engine developed a noticeable drone/vibration when in drive between 1600 - 1800rpm. RPMs above and below that range is fine. But when accelerating, as soon as the RPMs reach 1600, you can feel a slight vibration through the gas pedal and a noticeable sharp draon/moan up till about 1800 or 1900 rpm, then its normal.
I took it to my ford dealer and took the service manager out for a test drive. He said that there is a drone and slight vibration withing that RPM range. He thought that the engine mounts may be loose. But aside all that, he felt something was off and wrote up the service order.
When to pick up the truck and now the service manager changes his tune and said that the drone is normal and happens on all 6.2L super duties.
To be honest, I have the feeling he is pulling my chain.
Ford Super Duty (1999-2016) :: 2000 F250 - Vibration When Accelerate Pretty Much Any Load Above 1200 RPMs
I have a 2000 f250 crew cab short bed 7.3 on a 6inch bds lift and 37 inch tires. When I accelerate pretty much any load above 1200 rpms I can feel a vibration, kinda feels like it may be coming from the front left but I'm not sure. I have heard that a wheel bearing going out can cause this, would this maybe be what's causing it?
I thought wheel bearing because it kind of sounds like there's a howl when decelerating, probably when accelerating as well but the trucks too loud and I can't hear it. or also have heard motor mount gone bad, I've also heard ujoints but the ujoints were done this summer. the front ujoint is bad but the front driveshaft shouldn't be turning when out of 4x4 and hubs unlocked.
Ford Super Duty (1999-2016) :: 2001 F250 - A/C Goes In And Out
Okay, so the truck is a 2001 F-250 Crew-Cab 7.3l PSD with about 300k on the clock. For a while now the A/C would start out okay when you started the truck and it would blow cold for about 10 minutes then it would start to fade away and get hot. Then later it might get cold again. You could turn the A/C off for a minute or so and turn it back on and it would be cold again.
Took it to a shop and they drained the system and recharged it and they couldn't find anything wrong with it. Well, it's still doing it. We were starting to thing maybe it was an electrical issue with the cold/hot switch on the dash until a recently noticed a pattern. If it had gone hot and I got heavy on the accelerator (revving above 2500 RPM), it would get cold and keep blowing cold for 3-5 minutes. So the trick to staying cool as of now is just to hammer down every few minutes.
I read the HVAC FAQs, and it seems like the issue maybe with a slipping compressor clutch. Sound right? Also if that's the issue, it says the solution is: Excessive A/C clutch gap due to clutch wear. Usually, the problem can be resolved by removing a shim from the clutch to bring the gap back into the desired .014-.030 gap. What exactly do I have to do? Where and what are these shims?
Ford Super Duty (1999-2016) :: 2001 F250 - 4x4 Won't Engage
My truck: 2001 F250 V8 Triton Automatic 4x4
Problem: 4x4 won't engage
Symptoms: No dash lights....nothing happens when I turn the 4x4 switch. When I start the truck I hear what sounds like a motor (transfer case motor maybe?) trying to switch (even though my dash switch is on 2WD)... It tries three times and stops.
What I've done: Checked fuses ...they appear ok to me
I don't have a maintenance manual yet ...
The 4x4 used to work up until about 2 weeks ago. Started having a hard time getting it to go into (and out of) 4x4 and then it just stopped all together.