Ford Super Duty (1999-2016) :: Truck Shaking When Accelerating / Idling And Driving At 1500 RPMs
I got a 2000 f250, 5.4l, I got a check engine light bout 2 weeks ago and didn't experience any driving issues. The code was p0171, just recently I've been experience troubles idling, if I let my truck idle for about 3 minutes it will want to shut off, also on acceleration the hole truck bumps, feels like I'm in an earthquake. Where I should start with this problem?
View 11 RepliesFord Super Duty (1999-2016) :: 2008 F250 Truck Shaking Violently At Over 45
2008 f250 standard cab long bed 2wd base model 5.4. This thing has been great for the last few years i i owned it but it developed a shake since i got new tires. My mechanic mounted 4 new Hercules Terra trac at 2's on my 18 inch wheels (275 70 18) and when i got the truck back it was shaking violently at anything over 45. Mechanic says the new tires are heavy and its affecting other things...sounds plausible. So here i am a month later with a New steering stabilizer, all new ball joints, new shocks, new u joints, and 1 new tire (he said 1 of the brand new Hercules had a broken chord). The shake is 80% gone but this truck is still not the same. Anything after 65mph and it has a feint wobbly bouncy shake. I don't think its the dreaded hop that everyone gets on these. I have 2 theories:
1. These cheap tires just suck and will never be right
2. The cheap junk Monroe shocks he put on are way too soft to do anything
so what do i do? Should i get some crazy shocks or will that make this truck even bouncier? Im worried about making it even stiffer than it already is.
Ford Super Duty (1999-2016) :: 2003 F250 Starts / Barely Bounce Off Zero RPMs And Die Out
I have a 2003 F250 with the 5.4 and I believe I am having a fuel delivery issue. I took out yesterday and stopped to get a drink at the gas station, came back out and the truck wouldn't start long enough to idle. It would start, barely bounce off zero rpms and die out. I checked the fuel interia switch and it was down. I tried turning the key back and forth thinking it might reset the fuel pump or something and that didnt work. I get the truck towed home and couldn't get it to start last night. I go out this morning and it starts, come home from work and now it won't. This happened about 2 years ago and I never did anything about it, but it took 2 years for it to happen again.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Truck Will Not Stop Shaking When Driving
I have a 2008 F250 crew cab lariat 4x4 with 20 inch factory wheels that the steering wheel shakes during normal driving left to right. I bought this truck with 1500 miles on it. This shaking started at 50k miles and I was thinking it was a balance issue so I got new tires a month later since mine were about worn out anyways. They were factory replacement nitto terragrapplers. Shake was still there, swapped out for another set of nittos and shake still there, swapped to BFG AT KO's and shake better, but still there. I have gone through 10 or so balances, 5 roadforce balances, 2 alignments at 4 different shops including the ford dealer through the 3 sets. My wheels are scratched to hell and back from the careless people at the tire stores from so many balances.
My truck sat at the Ford dealer for a week just the other day and they changed the steering stabilizer. I thought it was gone, but a a few days later shaking started again. It almost feels as if every little bump, rut, crack in the road the steering wheel feels and shimmies (doesn't matter the speed, gets worse and more noticeable at higher speeds). The Ford Dealer says can't duplicate, but then when I go down there and test drive with them it's "oh yeah I see that, it shouldn't be doing that". The Ford Dealer says they can't find anything loose in the front end when I tell them to check tie rods, bearings, etc.
My truck has 62k miles on it now and it's driving me to the point of thinking about trading it on a Chevy. I love my truck, but it kills me everytime I make a payment and it rides like crap. I am still under extended warranty so I need to get this fixed before it goes out. I've also noticed that if I turn my steering wheel back and forth real quick while driving like warming up for a Nascar race I can feel a bumble in the steering wheel. This is NOT the death wobble as I use to get that around the 20k mile range and it disappeared and has never been back.
Ford Super Duty (1999-2016) :: 2011 F250 Truck Shaking Badly When Put It In Reverse
Well I just bought a 2011F250 6.7 on Friday. The truck has 42000 miles when I picked it up and now has almost 42800 4 days later. I love the truck so far. But anyways its an early build so is there anything I need to look out for? I noticed today I pulled into a parking spot and went to back up and as soon as I put it in reverse the truck shook pretty bad. It did it a few times as I sat there and went from drive to reverse. Is this something that is normal?
View 9 RepliesFord Super Duty (1999-2016) :: 2000 F250 V10 - Doing 2 Inch Level - Drop Pitman Arm?
I'm planning on doing a 2" level. Will I need a drop pitman arm, or can I stick with the stock pitman arm? Will I need anything else? I plan on doing the level when I replace my coil springs and shocks. (I have another thread on that). I'm driving a 2000 F250 V10 2WD CC SB (twin I-beam front axle) if that info is pertinent to this question.
View 2 RepliesFord Super Duty (1999-2016) :: 2000 F250 V10 Starts Then Idle Real Low And Die
I have a 2000 Ford-F250, V10, 6.8 liter Gas. The issue is that when I try to start the vehicle it will start, but then start to idle real low and then die. If I try to restart sometime it will and sometimes you have to let it sit. I can also pump the gas and it will sometimes start.
View 6 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Missing Between 1200 And 2000 RPMs
I have 2005 f250 5.4l 3v that was having miss problems between 1200 and 2000 RPMs. Changed VCT solenoids which worked, but then could hear chain hitting cover when powering down throttle on left side. Figured chain tensioner was bad, so tore down and removed timing cover. Found left chain was tighter than what seems normal, and right side had huge amount of slack. While taking off tensioner on left side, something happened to fast for me to see it, and still not sure if what happened wasn't just my imagination. I thought that the chain moved very fast for an inch or two. Anyways, I watched how to video on timing the 3v, but I am very confused about it. The left bank seems to line up on timing marks perfectly, but the right chain is off by at least 2 1/2 links. Not knowing any better, I removed three rockers on left bank (2 intakes and 1 exhaust) but only removed two intake rockers on right side. I don't know what I am doing and getting scared.
View 1 RepliesFord Super Duty (1999-2016) :: 2000 F250 Truck Won't Start Consistently
I just bought a 2000 F250 SD, 4x4, 5.4, Quad Cab. I drove it off the lot, stopped to put air in the tires, jumped back in and it wouldn't crank. All of the dash lights worked fine. Tried jumping at the starter solenoid and got nothing. Got under the truck and jumped it off the starter, vroom, fired right up. Replaced the starter solenoid and had no issues for about 2 hours. Then it did it again. This time it wouldn't start at all. I towed it back to the dealer and they had it for 3 weeks.
Then yesterday I called and they said it was done. Picked it up, drove to the barber shop, got my hair cut, came back out and it did the same thing AGAIN. After jacking around with the shifter and turning the wheel back and forth 100 times it started. The key is kind of hard to turn sometimes in the ignition, so I'm thinking that the ignition cylinder needs to be lubed real good, but that shouldn't stop it from cranking the motor over, right? I was going to swap out the ignition switch, but I don't know if that will do any good either.
Ford Super Duty (1999-2016) :: 2011 F250 - Truck Starts Beeping And Disable Alarm Start Vehicle Message Comes On Dash
Just picked up my F250 a few days ago and it's been great up until yesterday when I hopped in to start her up and nothing. It's a brand new battery and all lights worked, but the dash was dead. I attempted in vain for an hour or so to diagnose as to why this was happening and just happened to open the door with the key in the ignition and hit the door lock button....all of a sudden the truck starts beeping and the message on the dash said "to disable alarm start vehicle". I turned the key, the dash lighted up and away I went. What I may have done to cause this or has it happened to you? I'm thinking it's something with the key fob but not sure.
View 6 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Vibration When Accelerate Pretty Much Any Load Above 1200 RPMs
I have a 2000 f250 crew cab short bed 7.3 on a 6inch bds lift and 37 inch tires. When I accelerate pretty much any load above 1200 rpms I can feel a vibration, kinda feels like it may be coming from the front left but I'm not sure. I have heard that a wheel bearing going out can cause this, would this maybe be what's causing it?
I thought wheel bearing because it kind of sounds like there's a howl when decelerating, probably when accelerating as well but the trucks too loud and I can't hear it. or also have heard motor mount gone bad, I've also heard ujoints but the ujoints were done this summer. the front ujoint is bad but the front driveshaft shouldn't be turning when out of 4x4 and hubs unlocked.
Ford Super Duty (1999-2016) :: 2000 F250 Truck Acts Like It Wants To Stall When Stopping
New issue I've discovered , when stopping , the RPM's drop down to 500, truck acts like it wants to stall , then goes up to 750 RPM's . Then it's fine . Doesn't hesitate when accelerating . Idles slightly rough after start up , about 30 seconds . I've checked the air filter , cleaned the IAC and MAF. Fuel filter is only a year old . What I should check next ?
View 14 RepliesFord Super Duty (1999-2016) :: 2000 F250 V10 Truck Started To Have A Miss Under Normal Acceleration
Question, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 RepliesFord Super Duty (1999-2016) :: O/D Button Working Inverted - RPMs Drop
Push the o/d button to turn off, light on shifter comes on as off...and the rpms drop.
Push the button again (turning O/D on) and the rpms increase. It appears its working 180 degrees opposite of proper.
Example to clarify...going down hill at speed, push the O/D off button and as before working correctly the rpms would increase allowing the engine to aid in some braking.
That is now 180 degrees opposite. Push that button while descending and the rpms drop like it got thrown into neutral.
Ford Super Duty (1999-2016) :: 2000 V10 F250 - Temp Gauge Suddenly Shoots To Max / Truck Goes Into Limp Mode
My F250 with V10 has developed an overheating problem. While driving, the temp gauge suddenly shoots to max, and the truck goes into limp mode. Turning off the truck and ignition, waiting a few minutes, and all seems to be well again - sometimes for only a minute, sometimes for several days. No steam leaking, the water in the reservoir seems to be normal temperature, the radiator is not overly hot, and the AC keeps on blowing ice cold. Me thinks it is not really overheating, it just thinks it is. So where to start? Change the temp sensor first, or the thermostat? It seems the hoses are fairly firm, I don't believe they are collapsing from suction.
View 14 RepliesFord Super Duty (1999-2016) :: Truck Shudders And Almost Dies When You Drop It In Gear - Code P1747
Its a 1999 f250sd 5.4l auto. Has code p1747. Truck shudders and almost dies when you drop it in gear, put it back in park idles fine. I have read all the post on here about this and checked wires from trans up to pcm look and test good. Tested plug c1048 wires with digital meter to body ground with battery unhooked and got 6.66k ohms on pin 11 circuit 925, 421 ohms pins 1 and 12. Plugged c1048 back to trans checked 925 w/y wire at plug c103 got 9.1 ohms back to trans. Is the epc solenoid bad or is it pcm. I think its epc but want to verify before i take trans apart.
View 3 RepliesFord Super Duty (1999-2016) :: 2012 F250 XLT Stalling - Idle Drop To 500
I just purchased a 2012 F250 XLT with the 6.2. It has 38,000 miles on it. Yesterday I noticed, when coming to a stop, the idle will sometimes drop below 500. The engine will stumble a little, then the RPM will jump up to 1,000. Twice it has stalled on me. When it stalls, the engine will restart just fine. No codes in the computer or warning lights on the dash.
I will be bringing it back to carmax, as it is under their 30 day warranty still. Hopefully they will be able to figure out something. I am thinking either the TB needs to be cleaned, or there is an issue with the canister purge valve. I saw the TSB for the CPV but it doesn't cover my truck.
Ford Super Duty (1999-2016) :: F250 V10 Misfire - Shaking At 80 KMH
I have a 1999 f250 v10 auto. It has 3 miss fires thats im stumped with .. Ive replaced all spark plugs, all coils , I've had injectors out and were cleaned and it still miss fires. I can disconnect the coil and injector on the cylinders and the motor runs the same. Ive swapped the coils and injectors around to make sure it wasn't them. What else could it be? Frustrated I've had the truck for 2 years and haven't figured them out. Ive had them go away for at most a day. Also the truck has a shake at 80 kmh not sure if its from the miss...
View 13 RepliesFord Super Duty (1999-2016) :: Shaking And Grinding From Front Driver Side Of Truck
My truck has an intermittent shake with a grinding/binding kind of noise. It seems to happen at lower speeds, generally when slowing down and turning. When I apply the brakes or speed up it seems to stop the noise.
The rubber/plastic seal on the back of the wheel hub is loose on both drivers and passenger side but I don't think that is the problem. I'm wondering if it is the u-joints or something.
The brakes look shiny and i don't see any scratches on them so I don't think there is a rock or something in there. I have the wheel hubs in the auto setting, and it is a 4x4. The truck is a early 99 7.3L with a leveling kit and 230k miles.