Ford Ranger / B-Series :: 1987 V6 - Intermittent Miss At Idle When Warmed Up
I have a 1987 ranger 2.9 V6. Have a intermittent miss @ idle when warmed up. What is the proper way to pull the codes from the computer, i,st something about counting flashes or lights...
View 6 RepliesFord Ranger / B-Series :: 1993 V6 Miss At Idle And Running Down The Road
1993 3.0 V6 5 Spd ... Changed plugs wires Cap and rotor put in a new idle control Valve. No Check engine light. When i am running down the road feels like it surges,hickups, while its at idle the motor shakes like no tomorrow. Just dont want to throw money at something and not be the part that was wrong. Truck has plenty of pickup runs like a raped ape going down the highway. seems when i accelerate the miss clears up and not there. RPM gauge needle has some movement in it. Also put in K&N filter fuel filter as well.
View 6 RepliesFord Ranger / B-Series :: Erratic Idle / Sporadic Miss / 3 Cylinders On Right Bank Dropping In And Out
Its a 1994 with 4.0, automatic, 4x4. Running fine, parked it, a week later I'm getting a bad but sporadic miss that according to the stealership is the 3 cylinders on the right bank dropping in and out. Driving down the road you can feel them drop out and when they come back its a kick in the pants like a turbo kicked in.
Shop says wires are good, plugs are good, and then lost me when they started talking around in circles and not making much sense.
What could make 3 cylinders all on the same side of the engine drop in and out? This wasn't anything that slowly came on. Fine one day, crap the next. The only thing I did prior to was replace the IAC because it was idling high, it was cruddy inside, and it looked like it was original. It was running fine after that till this issue popped up out of nowhere.
Mileage was claimed to be 178k but I'm beginning to suspect it's probably 278k.
Ford Ranger / B-Series :: No Power At Cigarette Lighter - Fuse Checks Good?
I have a 96 Ranger . Neither my cigarette lighter or the auxiliary right beneath it works. The fuse checks good at the panel and I also used one of the penlight 12 volt testers and it shows no voltage on the lighter housing. Could there be another fuse under the hood that shares that circuit or do I have an open somewhere and need to tear down the dashboard? I haven't been inside that dashboard since I replace my cluster and the lighter worked after doing so. But I wish to avoid going back in there.
View 3 RepliesFord Ranger / B-Series :: 2002 - No Power When Accelerating
I have a 2002 ford ranger with the 2.3l and 5 speed.
Long story short, previous owner adjusted the time because he accidentally got the motor out of time (he thought it had the belt, not the chain). So he had to take the intake, fuel rails, fan, throttle body, etc. Off to get to the valve cover to re-time it with the timing kit. After it was put back together, it ran awful. I bought it, checked the time with the timing light and it was good. I replaced the spark plugs, and then realized he had forgotten to plug the camshaft positioning sensor back in. So I did, and that did the trick. From start to finish, the truck had those issues for about a year before I got it so it sat up for a little while. I have had it for 2 weeks now.
Now the problem...it idled great. But when I took it out for the test run, 1st gear shifted great, but at about 1700-2000 rpm (depending on the gear), it would almost seem to loose power, and then it would pick back up around 2400-2700 rpm like nothing had happened. You can sort of tell in 2Nd gear, but it is very noticeable in 3rd, 4th, and 5th. If i accelerate pretty slow, it doesn't happen. It only if i try to accelerate at a normal rate or if i am trying to get onto the interstate or pass someone. I ran some seafoam in it thinking maybe it just got gunked up from sitting for so long, but that only through an engine code saying my bank 3 was misfiring.
So I replaced the spark plugs (again), wires, and then the coil pack (the coil pack is what fixed it) and that got the code to go away and for it to stop missing, but the problem still was the same. It would take off great, and then it would seem to almost pause, and then pick power back up again. It wasnt feeling like it isn't getting enough fuel, it just wouldn't hardly pick up speed. It almost feels like I am riding a 2 stroke dirt bike. The power band is ehat should be normal on the truck, and before I hit the power band is how it feels when the truck has its little pausing episode. It's that noticeable to me.
So I thought maybe the fuel filter or sensors need cleaned/replaced..so yesterday I replaced the fuel filter and cleaned every sensor around the top of the engine, including the MAF sensor and made sure all bolts were tight and gaskets were good. I don't see and disconnected vacuum lines and none of them looked dry rotted. The only place air can get in that I see is the air filter box. The screws that hold the top half of the (stock) filter box are missing, so it is not sealed.
But what to check next. My only other thoughts are the catalytic converter (which it doesn't act like it's stopped up) or the fuel pump pressure being off. Also, it does sound like a lifter ticking in the motor, but previous owner said he thinks it did that before all these problems.
Also, right before I bought it, it sounded like the ujoint was squeaking (it rarely does it now) and now it has a crackling sound when accelerating at low-mid rpms coming from the middle or the back of the truck. It sounds similar to when you turn your hot vehicle off and the exhaust makes crackling noises sometimes.
Ford Ranger / B-Series :: 1987 - No Power While Accelerating
1987 ranger 2.9l... My truck had no power while accelerating. We'll I changed fuel pump and filter. And still no power. I bought a computer and it tells me the map sensor is not at normal vaccum levels. The ego sensor is reading always rich. Egr valve not opening. Knock sensor was was going crazy. And computer couldn't raise engine speed above normal idle. Could all this be because of one sensor or should I just change it all.
View 7 RepliesFord Ranger / B-Series :: Getting Good Spark From All Cylinders But Not Starting
I just finished rebuilding my 1990 2.9 and it wouldn't start. When we did the initial start up, the truck needed ether to start and ran decently while stumbling. I found out that the spout connector was removed from the previous owner so I spliced it but still no starting ...
I installed a new fuel filter, fuel pump, cleaned the injectors, spark plugs, spark plug wires, distributor cap, rotor, air filter and cleaned the MAF. ..
Its not a spark problem because I'm getting good spark from all the cylinders and yes the timing was set correctly. It sounds like it wants to start but just doesn't have something to make it boom. There are also no codes...
Ford F-150 (2004-2008) :: Engine Vibration / Miss At Idle - Slight Hesitation During Acceleration
I posted a while back about my 04 5.4 having an issue at idle. I did all the normal things like replace coil, spark plug, etc etc. No change to the issue. It still acts as though it's misfiring on a cylinder and I get codes P0306 and P0316. Finally took it to ford and had a diagnostic check ran. Everything on the top end was in working order. The tech even put a known working coil on 6 and nothing changed. I was told that it's either an intake or valve issue on that cylinder. But no definite answer to problem.
Fast forward to yesterday. I got a wild hair at lunch and went out and started truck. Pulled injector plug off of 6. No change to the way it was running. I did the same for 5, 7, 8, 1, and 2. All of which made a big difference in the way it ran. It was obviously misfiring with no fuel to cylinder. This gave me the idea to swap 5 and 6 when I got home to see if the issue followed the injector from 6. I did NOT. I pulled the plug on 5 and got the obvious change in the way it ran. So there is definitely something going on at cylinder 6 that I cannot figure out.
PCM, bad intake, bad valve? I'm not rich so a trip to ford for repair is gonna have to wait. Truck seems to run fine when driving except for slight hesitation during acceleration.
Ford F-150 - 1997-2003 :: Slight Miss / Rough Idle - Hesitation Or Stumble On Acceleration
2003 F150 5.4 72852 miles
I have a Rough Idle & sometimes a hesitation or stumble on acceleration. I cleaned the MAF & IAC motor & Air & Fuel Filters are new. I got a 20890 scanner & ran test 6 53 as suggested in many posts by BlueGrass. Here are My results & what They Convert to.
1 00F5 .3675
2 0051 .1215
3 0000
4 0000
5 00A3 .2445
6 0000
7 0000
8 0000
I'm guessing the cop's are ok & probably need plugs? I was hoping to just swap a coil. Too cold to do plugs & truck won't fit in my garage.
Ford Ranger / B-Series :: 1998 - Random Misfire / Power Loss / Hesitation - Code P1131
Ok I've been plagued with this very random misfire/power loss/hesitation problem going on a couple of months. You could drive the truck anywhere from 50-300 miles without having an encounter of this problem. It seems to do it now mostly on contiguous long trips over like 30 miles. It one time threw up a P1131 code which quickly went away on it's own. This is a list of stuff that has been recently changed: plugs, wires, coil packs, air filter, pcv valve, fuel injectors, tps, idle air valve, MAF cleaned, fuel filter, and egr valve.
I sprayed with brake cleaner for vacuum leaks around the intake tonight after driving a continuous 50 mile round trip it messed a few times on the way back. When I sprayed the EGR valve mounting area it idled rough when it was hit with brake clean and idled up. So there's a leak there. Or is it stuck? It will be driving normal and usually when you come to a stop the engine will start missing really bad and then when you take off there's no power at all. You keep your foot on the gas and eventually it will feel like all the power is just turned on.
If it does it while you're driving highway speeds it will feel like you've lost a cylinder but it's not as dramatic as when you come to a stop and it starts missing. I can't be 100% but I don't think the EGR wasn't leaking before I replaced it and it was still doing the same thing. I'm wondering why the Check Engine Light won't pick up an obvious misfire when you can you actually feel it. And why if it was the vacuum leak would it only start doing it after many miles of driving?
Ford Ranger / B-Series :: 2002 Engine Won't Turn Over With A Good Battery
I have an '02 Ranger 2.3L 40k miles that will not turn over even with a good battery. When the key is inserted and turned, all the dash lights and headlights come on but the engine does not turn over. Could it be....
*Power Control Module?
*Ignition Module?
*Key?
*Whatever the part is called that reads the Key's security code.
*Clutch Switch?
I am trying to avoid getting the run-around at the dealer and be able to drive to work on Monday!
Ford Ranger / B-Series :: 1999 - Miss With A/C On?
My 99 ranger has a strange issue its got a miss when the A/C is on, when going down the road I can feel the engine sorta pulse for a second, gets better the more I drive it, its got all new plugs and wires, not sure where else to look?
View 1 RepliesFord Ranger / B-Series :: 1998 - 4.0 OHV Miss Under Load
I have a 98 4x4 with 145k miles and 4.0 OHV. Symptoms are as follows;
Uses ALOT of oil. 1 quart per 230 miles. Burning bad in rear cylinders, some in middle cylinders, none in front cylinders. Screams intake or PCV issues to me, not rings or valves. Never any smoke, not even on startup. No significant leaks. MPG always 18-20mpg.
Slightly rough idle.
Miss under load below 2k rpm. Not a terrible miss, but you can feel it. Has never lit the CEL. I know the CEL is good.
Never loses coolant. No coolant in oil or vice versa. Haven't done compression test, but doesn't seem like they ever tell you much anyway.
This weekend I replaced all intake gaskets, plug wires, cleaned oil residue off and regapped plugs (they are 3 months old), injector orings, and PCV valve. Flushed and burped radiator.
It's too soon to tell on the oil consumption, but I thought the intake gaskets would have cured the rough idle and misfire. The idle IS much better, but still not perfect. But the low rpm load miss is actually worse now. Still no CEL. Could it be storing codes without lighting the CEL? Also, how do you clear codes on these, can you just disconnect battery, or do you have to clear them with a scanner?
Golf V R32 :: No Idle / RPMs Surging And Hesitation When Taking Off
Got a problem with my R. 134k miles. About 4 months ago I had similar problems and was told it was a bad MAF. Of course wasn't covered by my warranty, so I decided to just give it a good cleaning and car ran fine up till now. Just started doing the same thing today. Doesn't want to idle, taking off is really hesitant then it just goes. Trans seems like it is struggling to find the correct gear sometimes when coming to a stop or taking off, sometimes jerks hard, maybe throttle position sensor, or idle control? Once you are moving it drives fine, only very low speeds and idling are the problem. Trying to avoid going to the dealership. What this could be? MAF need cleaned again or just replaced?
View 4 RepliesFord Ranger / B-Series :: Random Miss At Full Throttle
2002 Ranger XLT 4WD 4.0.. I was passing another car at about 55 when they also started speeding up (go figure) so I floored it and got on around them but before I lifted I felt it miss, the CEL began flashing so I slowed to the speed limit and went on to work. The light flashed for about a mile then went out. So on the way home I floored it again close to home and the CEL came on again. Got home and put the code reader on it and all it had was a random misfire so I have cleared it. The truck has new plugs, wires, etc for a complete tune-up. I don't usually run at full throttle so don't know if that would be normal for the Ranger, the Ranger was my wife's truck for 12 years and now is my DD. Need to clear this up? Thought of changing the fuel filter in that is still the original one.
View 8 RepliesFord Ranger / B-Series :: 2000 3.0 - Dead Miss / Not Consistent
Just hoping that there is something common that causes this problem. This thing can idle just as smooth as you could want one to and the next time it will have a dead miss, and the miss is not consistent. It may miss like three hits then be ok a little then miss a little. There is no CE light or codes. Again just hoping there is something common.
View 2 RepliesGolf IV / Jetta IV :: Rough Idle - Hesitation In First Gear Taking Off
So this morning when I started my car to warm up everything was fine. I went inside to make some coffee and I heard my idle change slightly and didn't think to much about it but when I got in I could feel my car shaking a little bit then when I pulled off my road there was a little hesitation in first gear taking off and when I would shift I would get a little rev hang between gears. So I've realized when idling its slightly fluctuating between 6-7 hundred rpm. I have no loss of power and it has not hesitated since the first take off. I'm thinking its something to deal with air. I checked my airbox and realized the bolt closest to the battery wasn't threaded so I fixed that and tried looking for any leaks but haven't found anything.
View 4 RepliesFord Ranger / B-Series :: 2007 3.0L - Bad Low Speed Miss From A Stop To 1500 RPM
I have at 2007, 3 liter ranger. I just replaced the plug wires and coil pack. Ive checked and rechecked the wires, firing order is right,everything has spark but i now have a miss from a stop to 1500 rpm. what do i need to do to fix the issue.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Hesitation / Miss During Acceleration
My truck is developing a hesitation or a miss when accelerating. It only does it in the beginning of accelerating like when just starting off from a stop. Seems like its more noticeable with the more I get on it. If that makes any sense. When just lightly accelerating it doesn't do it, like going slow through town from light to light. But when I give it more is when I feel it. It seems like it only does it before the turbo kicks in and it puts out a little smoke too only before turbo kick in. After that it runs good with no noticeable miss or anything. WOT runs feel good after it clears up. Its just when first starting out with anymore that 1/4 throttle I can feel it.
View 14 Replies