Ford Ranger / B-Series :: 1986 Just Cranks But Won't Start
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 RepliesFord Ranger / B-Series :: 1999 - Cranks But Won't Start?
Ok, went out last night to go over to a buddies place to watch some football. Tried to start my truck but all that happened is that it would turn over, but not start. Had plenty of juice in the battery, and 1/2 tank of gas. It acted like it wanted to start, but nothing doing - just keeps cranking and cranking. Its even more frustrating because I was driving it around most of the day before this happened.
Here's the dillema: Its been doing this for the past two months now on and off. Once I fix something, it runs for about a month, and then it starts doing this again, without any warning signs (i.e. multiple cranks before a start, stalling, hesitation on accel., etc.). At this point I'm clueless. I've replaced the fuel filter, fuel pump, and air filter, but the problem has resurfaced again.
An interesting thing to note is that the only ways I'm able to get it started when it starts doing this is to remove the electrical connection from the intertia switch, and crank the engine a few times to relieve the fuel system pressure. After reconnecting the inertia switch, the truck starts instantly.
So whats the deal? Why this would work, and why suddenly the thing would not start after weeks and weeks of driving flawlessly? Is it possible that my system is either too pressurized or losing pressure somehow, and that is how it be able to start? A buddy suggested it might be injectors, but I'm not so sure, because there is no hesitation on accel or performance loss, or even a rough idle.
Ford Ranger / B-Series :: 1999 2.0 - Cranks But Won't Start
My 1999 Ranger that I bought used has been serving me well. However, two days ago I went to visit a friend and when I tried to start the truck to go home, the engine cranked but would not fire. I assumed that perhaps I had flooded the engine, so I walked home. I went back an hour later and the truck started up immediately. Then, yesterday, the truck would not fire at all. I towed it to AutoZone to check for error codes, but none were found. I put my inductive timing light on a plug wire and found that there was no spark.
In one instance of cranking, the timing light blinked and the engine tried to fire, but then nothing. The AutoZone man suggested changing the crankshaft and camshaft sensors. I haven't done that yet, but that is my next plan. Can the Ford dealer find error codes that tell what is preventing an engine from starting that AutoZone can't see? For sure there is no spark, but maybe there is no fuel either since I don't smell gas after much cranking. Could it be the inertia switch cutting off both fuel and spark?
Ford Ranger / B-Series :: 1994 - Engine Cranks But Won't Start
My kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
Ford Ranger / B-Series :: 2004 - Won't Start But Cranks Strongly?
2004 3.0L Ranger Edge, 88,000 miles on it, I am the original owner. It won't start. It cranks strongly. Usually when this happens, I have to reset the fuel pump inertia switch. This time, resetting the switch does not work. I disconnected the switch and jumped the two wires going to it, but still no start. The switch seems to work ok, in that I can reset it (a ball, spring, and magnet mechanism, I think), then shake it and the ball will come loose.
The fuel pump 20A fuse in the engine compartment is good. The fuel pump relay in the engine compartment is good (I switched it out with an identical relay that runs the fog lights without problem). I am getting spark. I don't have a fuel pressure gauge but pressing in the Schraeder valve on the fuel rail produces gas.
Usually, when the inertia switch is tripped I can get the engine to briefly start by using starter fluid in the air intake. But not this time. I do not hear the fuel pump kicking in when I turn the ignition key to the "On" position, and that would lead me to think that the pump is bad. Except, I don't get a brief start using starter fluid. The fuel filter has never been changed, but again, since I get no start with starter fluid, I don't see how that could be the problem. OBDII scan shows no codes.
Ford Ranger / B-Series :: 1984 Has Spark / Cranks But Won't Start
working on a 84 ranger it did run fine for 3 wks then while driving there was a thump and it stopped and wouldn't start. Now working on it has spark cranks but won't start. while trying to start when I let off the key it tries to catch but only at that time not when the key is turn to start normal. we poured fuel into the carb and it still didn't start. Leaning toward compression maybe?
View 4 RepliesFord Ranger / B-Series :: Truck At Times Cranks But Does Not Start - Hot Or Cold
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
Ford Ranger / B-Series :: 1998 4.0L Cranks But No Start / High Fuel Pressure
Made a trip to the hardware store yesterday. When I came out, the truck would crank just fine, but wouldn't start (98 4.0L 4x4). Tried adding gas, no luck. I had actually called a wrecker, but it eventually started after sitting for about an hour. All I did differently was hit the gas pedal a couple of times. Thinking it may be a low fuel pressure problem, I took it to autozone this morning (started it about 4 times now with no problems). Checked the fuel pressure, and it sat at a solid 65 lbs at idle. I tried holding the throttle open and it stayed at the same pressure. I forgot to try with the vacuum off.
First off, I've seen some people say 60 lbs is right, but more say it should be at about 45lbs. 45 seems right since the fuel return is on the block, not on the pump. I'm guessing the fuel damper went out, but is there any good way to check it? Also, since the damper is vacuum controlled, would a bad vacuum cause this problem? Third, could high fuel pressure cause it to not start? That's the one I'm most worried about what was wrong there.
Ford Ranger / B-Series :: 2002 Won't Start / Cranks Over But Back Fires And Bucks A Lot
i just rebuilt the motor in my 2002 ford ranger 3.0 and it wont start it cranks over but back fires and bucks alot. took the plugs out and it gets spark and fuel. when it sparks it sparks like multiple times.
View 3 RepliesFord Ranger / B-Series :: 2003 - Long Start - Cranks For 15 Seconds Before It Fires
So it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
Ford Ranger / B-Series :: 1987 V6 Won't Run Longer Than 5 Minutes
I have an 87 v6 ranger with 5 speed that has been sitting for several years. The truck only has 48000 miles on it. The gas tank has been cleaned out and both fuel pumps have been replaced. The injectors were pulled and cleaned...
It will start up and run for about 5 minutes and then will shut off. It will not start after that until the next day and then does the same thing. It starts up and runs then shuts off and can't get it to start again. Could it be some kind of circuit breaker tripping or maybe the ecm. If it is the ecm how do you test it...
Ford 6.0L Power Stroke Diesel :: 2007 F350 Cranks Over Longer Before It Starts
Lately it seems that my 6.0 cranks over longer before it starts. it used to turn over quick and start not it turns over at least 5-8 seconds maybe more. .
View 7 RepliesFord Excursion :: Check Engine Light Came On / Cranks Longer To Start
I have an 05 diesel. I have noticed the last 3 days I needed to crank it slightly longer to start it and it takes a second before ideling normally. It usually fires right up and jumps to life. Today i drive about 45 minutes. Stoped for about 30 minutes and shortly after I started it back up the check engine light came on. Will the Ex flash you the codes or do you have to have a reader? Thought I would try Autozone tomorrow but not sure if they read deisel codes or not. I was suspecting maybe glow plugs but who knows at this point. It seems to be running fine and I checked all fluids.
View 13 RepliesFord Ranger / B-Series :: 1993 - Taking Longer To Shift Into 2nd Gear / RPMs Are Way Up
Recently my 93 Ranger 4.0 has started to take longer to shift into 2nd gear and the rpms are way up there. shortened 2nd gear then 3rd will be fine and so on. This only happens after the engine goes completely cold. I took it to a transmission shop and they said tranny is fine...Other than this issue the truck is fine.
View 6 RepliesFord Ranger / B-Series :: 1998 - No Spark / Cranks But Does Not Fire
My father in law has a 98 4wd, 4.0L that cranks but doesn't fire. We pulled a plug to check for spark....no spark. Possibly coil pack, or crank position sensor?
View 5 RepliesFord Ranger / B-Series :: 1995 - Cranks Just Fine But Won't Fire
I have a 1995 ranger with a 4.0 it cranks just fine wont fire has alot of fuel spark it will crank and crack then it stop and acts like it is going to fire up and stops cranking... This thing has 253k on it...
View 4 RepliesSilverado :: 2001 Truck Cranks But No Longer Start
My silverado no longer starts and the fuel gauge no longer reads. so far figured out that there is no power to the fuel pump and sending unit. Looking for an engine wiring diagram for this truck with the 6.0 engine?
View 14 RepliesFord Ranger / B-Series :: 2004 - Cranks But Does Not Fire At All After A/C And New Battery Install
I just finished putting in aftermarket A/C in the 2004 Ranger my dad gave my son. It's a 2.3L, STD transmission. It was running GREAT before the project started. I installed new battery as part of the project. When I started it back up it ran for 2 or 3 seconds then died. I now cranks, but does not fire at all.
I have tried one of the key reprogramming sequences (turn key to "ON" 8 times) with no success. Would it crank at all if it were a key security issue? Is there anything I need to reset anywhere else, like in the air intake system?
It's either not getting spark or not getting air. The fact that it ran for a couple of seconds has me confused. Would it run at ALL if there was a key security problem?
I had to remove and reinstall the air filter housing and ducting. Is there anything else I need to do to with the air intake system?
Ford Ranger / B-Series :: 2004 - Changed Push Rods Now Car Cranks But Won't Fire Up
2004 ford ranger 3.0 ... So here it goes I am pretty mechanically incline for the most part i would say until this last week i got a rod knock. So i replaced all my push rods put everything back together and now my car cranks but just wont start up where did i go wrong. I cant afford to get another truck i just want my baby back up and running ...
View 14 Replies