Ford Ranger / B-Series :: 2004 - Tranny Going Out?
Looking at buying a new truck. We'll in a crunch actually due to my tranny going out this morning. One that I'm looking at looks great, except the obd2 port is dead. Where do I start looking? What fuse etc. It appears auto correct changed the obd2 to body and I didn't catch it...
View 8 RepliesFord Ranger / B-Series :: Installing Timing Belt?
I've tried every variation of installing the timing belt on my '91 2.3L Ranger, still not in. The belt seems as if it's too short but I've been told that it "barely" fits, no kidding! I've pulled the crank balancer/timing trigger off and put it back on three or four times already. What's the trick? Everytime I get it close I'm off a tooth or more. Just frustrated, tired of hitching a ride to work.
View 14 RepliesFord Ranger / B-Series :: 2011 - Installing Cold Air Intake?
I would like to install a cold air intake in my 2011 Ford Ranger. What brand should I go for? Volant or K&N?
View 4 RepliesFord Ranger / B-Series :: 1995 - Changing Tranny Fluid?
. I'm going to FINALLY change the tranny fluid in my 95 Ranger Splash this weekend and need all the feedback I can get! It's a manual trans with miles shy of the 250,000 mark...still on the original stuff!! I'm only the 2nd owner but I bought the truck with just 45,000 miles on her so I'm willing to bet the farm that it's never been changed. It's getting harder to shift from 1st to 2nd and I'm getting a little bit of grinding from 3rd to 4th if I shift too fast. Reading all the threads everywhere online, so many different people have so many different theories from stock Mercon V to MOTOR OIL??? The motor oil thing floored me but I understand the viscosity difference between hydraulic fluid and lubricating oil. figure out what the best thing to replace the original with to prolong the life of this long running wonder vehicle!
View 5 RepliesFord Ranger / B-Series :: 2011 - Installing Sliding Rear Window?
Installing sliding rear window in a 2011 ranger sport? Is this a DIY project or should it be left to the pros?
View 2 RepliesFord Ranger / B-Series :: 1991 - Tranny Slipping / Swap Options?
1991 Ranger 4.0L A4LD... Its a 4x4. ext cab
What else will bolt up to this 4.0L? Could i put a 4R44E/4R55E tranny? Is there a good stick that bolts up?
Ford Ranger / B-Series :: 2003 - Oil Build Up Under The Front End / Tranny Leaking?
2003 ranger 4.0 5 speed .... Pretty new to the car/truck world only 18 and this is my first truck, I traded my focus for it and so far so good. Its my first manual but i got to tinkering and i noticed some oil build up under the front end so i got to looking and found this, wondering if its an issue, should I try to fix whatever is causing it or take it to a mechanic. Looks like between tranny and engine to me.
View 2 RepliesFord Ranger / B-Series :: 2010 - Rhythmic Sound Only After Engine And Tranny Are Hot
Last week I noticed a slight "whomping" noise in my 2010 Ranger. Not a knock, not a ping, nothing that sounds metallic. Just a rhythmic whomping sound that only shows after the engine and tranny are hot.
It only does it in Drive or Reverse; and not in Park or Neutral. The tech at the dealership (30k on the vehicle) says he thinks it is a bearing in the torque converter.
Ford Ranger / B-Series :: 1991 4WD Manual Tranny Locks Up After Going Forward A Few Feet
My 4x4 4WD Ranger has a 5 speed manual tranny that locks up after going forward a few feet. It can back up all day long but locks up going forward. some god awful noises (grinding, clunking, etc) come out of that gearbox. the 4wd is electrically operated. the ? is , can this tranny be rebuilt with a kit? I'm having great difficulty finding a replacement. Are bronco II's compatible? Engine is 2.9L V6. On disassembly I found 2 meshing gears with broken teeth.
View 5 RepliesFord Ranger / B-Series :: 1989 - Tranny Input Shaft Seal Replacement?
I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.
Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.
Ford Ranger / B-Series :: 2002 - Shutting Down While Driving
Our Ranger, 2002, 4 cyl. 2.3 5 speed is shutting down while driving. This has happened twice very recently. Both times on interstate at highway speed. First it loses power then completely shuts down. After stopping, turning key "off" it restarts and runs fine. It does take a longer time to crank before starting.
It is not throwing any codes and the CE is not coming on. I suspect the fuel pump is shutting down. Seems like fuel pressure loss is reason for loss of power? Then extended cranking to restart is the initial build up? What else could it be? If not the pump itself, is there something that would take away power from the pump then get reset?
Ford Ranger / B-Series :: 2002 - No Power To Fuse 28
I just got my grandpa's 2002 Ford Ranger Edge after waiting years to obtain it. It runs great the only problem is that there is NO power to the radio what so ever. The truck belonged to the family and every one drove it but no one knows what happened.. There is no power to Fuse 28 however 12V to all other fuses that have to deal with the radio.
View 12 RepliesFord Ranger / B-Series :: 2002 - No Power On Acceleration
02 Ranger with 3.0 Flex motor, 375K+ miles. Been chasing an issue for a while now, but am about at the end of my diagnosing capabilities. Issue started with a misfire on 5 and rough running engine with no codes showing up. Now the motor is getting worse.
Idle a little rough and no power when accelerating hard. The engine sounds like a popcorn popper under hard acceleration. Motor revs up to 4K but does not pull or shift gears until I let off the gas.
The code that initially showed up indicated a bad Camshaft Position Sensor. Changed that and the Sync assembly - as per instrucions, exactly positioned same as old one. New codes showed up - P1152, P0175, P0171. Cleaned the MAF, rail fuel pressure OK, can't find any vacuum leaks, replaced both upstream ox sensors, and changed #5 ,6 injectors.
Motor still runs the same - like crap, like a corn popper on acceleration, smooths out if only slightly accelerating, but stumbles n bumps on steady cruise speed over/around 60 mph - and no codes showing at present.
I really, really don't want, nor can I afford, to take it to the dealership, but I may be forced to if I can't figure this out sometime quite soon. I make my living with this truck so, no truck, no work till this issue is solved.
Ford Ranger / B-Series :: 2002 - No Start When Shut Off
I have a 02 ranger..3.0 standard trans 4x4.... Started running crappy, cleared up and when shut off, now wont start... Good spark and good gas pressure... Seems to want to try, but just doesn't go. No codes or pending codes.
View 8 RepliesFord Ranger / B-Series :: 2002 - No Power When Accelerating
I have a 2002 ford ranger with the 2.3l and 5 speed.
Long story short, previous owner adjusted the time because he accidentally got the motor out of time (he thought it had the belt, not the chain). So he had to take the intake, fuel rails, fan, throttle body, etc. Off to get to the valve cover to re-time it with the timing kit. After it was put back together, it ran awful. I bought it, checked the time with the timing light and it was good. I replaced the spark plugs, and then realized he had forgotten to plug the camshaft positioning sensor back in. So I did, and that did the trick. From start to finish, the truck had those issues for about a year before I got it so it sat up for a little while. I have had it for 2 weeks now.
Now the problem...it idled great. But when I took it out for the test run, 1st gear shifted great, but at about 1700-2000 rpm (depending on the gear), it would almost seem to loose power, and then it would pick back up around 2400-2700 rpm like nothing had happened. You can sort of tell in 2Nd gear, but it is very noticeable in 3rd, 4th, and 5th. If i accelerate pretty slow, it doesn't happen. It only if i try to accelerate at a normal rate or if i am trying to get onto the interstate or pass someone. I ran some seafoam in it thinking maybe it just got gunked up from sitting for so long, but that only through an engine code saying my bank 3 was misfiring.
So I replaced the spark plugs (again), wires, and then the coil pack (the coil pack is what fixed it) and that got the code to go away and for it to stop missing, but the problem still was the same. It would take off great, and then it would seem to almost pause, and then pick power back up again. It wasnt feeling like it isn't getting enough fuel, it just wouldn't hardly pick up speed. It almost feels like I am riding a 2 stroke dirt bike. The power band is ehat should be normal on the truck, and before I hit the power band is how it feels when the truck has its little pausing episode. It's that noticeable to me.
So I thought maybe the fuel filter or sensors need cleaned/replaced..so yesterday I replaced the fuel filter and cleaned every sensor around the top of the engine, including the MAF sensor and made sure all bolts were tight and gaskets were good. I don't see and disconnected vacuum lines and none of them looked dry rotted. The only place air can get in that I see is the air filter box. The screws that hold the top half of the (stock) filter box are missing, so it is not sealed.
But what to check next. My only other thoughts are the catalytic converter (which it doesn't act like it's stopped up) or the fuel pump pressure being off. Also, it does sound like a lifter ticking in the motor, but previous owner said he thinks it did that before all these problems.
Also, right before I bought it, it sounded like the ujoint was squeaking (it rarely does it now) and now it has a crackling sound when accelerating at low-mid rpms coming from the middle or the back of the truck. It sounds similar to when you turn your hot vehicle off and the exhaust makes crackling noises sometimes.
Golf IV / Jetta IV :: 2000 - What To Do While Installing Tranny
I just picked up a 2000 VR6 golf a few weeks ago. been doing lots and lots of reading. It needs a transmission and was wondering what other things should I do why tranny is out of the way. I know some things can either only be done with tranny out or are a hell of a lot easier with it out of way. So what are your recommendations. Looking to pick up a tranny and get this bad boy on the road asap. Car ran great no issues or sounds my buddie just shifted to 3rd on highway and something walked loose in tranny and kaboom she went.
View 5 RepliesFord Ranger / B-Series :: 2002 - Changing Fuel Filter
Where is is my fuel filter and what are the steps to changing it. I have a 2002 Ford Ranger. Also how do you change the flashers, the left blink is really fast but the right blink is fine.
View 14 RepliesFord Ranger / B-Series :: 2002 - Running Rough Like Misfiring
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
Ford Ranger / B-Series :: 2002 - Occasional Misfire At Idle Only?
Misfire is on #6. Feels like a partial miss, not every revolution, and there's no noticeable miss while cruising or holding a higher rpm in neutral. It's a B3000 with 97k miles. New Motorcraft plugs, new wires, 10.7k ohms across coil terminals (1-5, 2-6, 3-4).
I've swapped plug wires between cylinders and side-to-side on the coil. I also sprayed MAF cleaner all around the intake looking for a leaky gasket. I feel pretty confident I'm looking at a bad/dirty injector or valve issue. I plan on doing a compression test next and hopefully nail it down to one or the other.
I'm asking for input on my diagnosis so far. And how difficult is it to replace the injector? Will I need to remove the upper intake?