Ford Ranger / B-Series :: Hard To Get Out Of 2nd Gear / Engine Surges Then Starts To Lose Power
My surging/running down issue has returned on my '86 2.3l Ranger. I thought it was electrical, when things improved with the new ignition switch, but lately it's hard to get out of 2nd gear before the engine surges then starts to lose power. a poke of the gas pedal starts the who cycle over again. I pulled codes but it's hard to tell what the reader is saying either 33 and 34 or 334. The good thing is all the codes point to the EGR system. Looking for a diagnosis tree to determine if the valve is bad or the sensor is shot? They are both not cheap so I don't want to just throw parts at the problem.
View 14 RepliesFord Ranger / B-Series :: 1999 Cranked Up But Starts To Die Out
1999 ranger 2.5L.. I cranked it up. but it starts to die out. so when i give it some gas it stays on but it runs really rough (obviously). it shakes pretty nice. but as soon as i let off the gas it dies out. I am guessing its either air or fuel related. Any takers? Where should i start?
View 4 RepliesFord Ranger / B-Series :: 1999 - Trans Won't Shift Into Any Gear
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
Ford Ranger / B-Series :: 1999 - Shaking When At Idle In Gear
I just got a 99 2.5 rwd auto and it shakes when it's at idle in gear. I'm pretty sure its because the AC pulley is engaging drawing power. I was thinking about turning the idle screw up a blonde-one because when I hold the brake and give it slight gas it goes away.
View 3 RepliesFord Ranger / B-Series :: 1999 - Trans Slipping In 1st And 2nd Gear?
I have a 99 Ranger 3.0L automatic, ext cab, 2 wheel drive. Door sticker show code "T" which I looked up as the 4R44E. The trans seems to be slipping in 1st and 2nd. Thought it was "reared shudder", from a "limited slip" differential but mine is not limited slip. just the regular 8.8 with 373 gears.
Wanting to know what if any options I have for buying a new / rebuilt tranny? I've seen where depending upon the year and motor, Ranger can have 4r44e, 4r55e, 5r55e, etc.
Ford Ranger / B-Series :: 1999 - Hard To Shift Smoothly Into Third Gear
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 RepliesFord Ranger / B-Series :: 1999 - M5OD Popping Out Of Third Gear Occasionally
My M5OD in my 1999 Ranger 4x4 with 3.0 occasionally pops out of 3rd gear. I think it does it only under light throttle or coasting. Also some vibration, especially in 3rd gear. Once in a while the gears grind when shifting into third. Truck has 145,000 mostly highway miles. Frequent fluid changes with Redline D4ATF.
What could be the cause, bad synchros ? How hard is it to remove the transmission and make a repair for something like this, what kind of special tools, etc. I assume a transmission jack would be real useful, what else would I need other than the normal wrenches and sockets ? Is there a good shop manual recommended for doing this repair ?
Ford Ranger / B-Series :: 1988 - Won't Idle - Starts Right Away Then Die?
88 ranger. 2.9L manual. Just bought this truck. It ran great when I bought it. After a day or 2 it would idle rough. Almost die but it wouldn't. No check engine light. It seemed to do this intermittently. Some times I'd start it and it be fine. Other times I'd start it and I'd expect it to die at each stop light.
Now for the last couple days it dies on every start up. It won't idle. It'll start right away and then die. I can keep it going by keeping the engine rev'd but the check engine light is one. If I keep it running and start driving down the road it'll drive with the check engine light on for about 5 minutes. Then the light goes out and it runs like normal, even at idle, until I shut it off. Then it's the same story at next start whether it's right after I shut it off or hours later.
It doesn't seem to matter whether the engine is hot or cold. When the check engine light is out, it runs great the rest of the time whether at speed or at idle. To me it sounds like a sensor is on it way out. I figure if it was vacuum, it happen at every idle, and if it was fuel it happen all the time or at least every idle. Tried to get a code at parts store but the reader wouldn't work. It couldn't tell it was plugged in the the truck for some reason.
Ford Ranger / B-Series :: 1997 XL Won't Run / Starts But Will Not Idle
i have a 97 ranger xl with 2.3. it was recently crashed in the front, air bags deployed. i fixed the bodywork but couldn't get it to run properly. it starts but will not idle. i have replaced the iac , evr , maf. fuel pressure holds 35-40 psi running does not leak down after engine stops
View 9 RepliesFord Ranger / B-Series :: Starts Then Dies After Few Seconds
I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?
View 14 RepliesFord Ranger / B-Series :: 1995 - After Warm Up Starts Idling - MAF?
I have a 95 4.0 EFI inside of my 83 Ranger. Once the motor warms up, it starts to have an idle issue. I have to press the gas, in order for it not to cut off. Here is a video I posted a while back. A person suggested that it could be the MAF needed to be cleaned. I did that, and it did not work.
View 9 RepliesFord Ranger / B-Series :: 1992 - Starts And Stalls / Won't Run More Than 3 Seconds
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 RepliesFord Ranger / B-Series :: 1994 4.0L - Starts / Stumbles And Dies Soon After
Ole girl finally let me down, or I let it down at 224,000mi. Started just fine one early cold morning and in about 30 seconds started stumbling and down for the count she went. Acts like it wants to run but will only stumble.
Checked inertia switch (ok) and all vacuum lines/caps appear to be fine. I was kind of due for new set of plugs/wires and a fuel filter. Replaced all didn't see any problems with the old when pulling. She will run for a few seconds, but stumbles and not smooth while running. Checked fuel pressure KOEO 40psi steady. I can hear fuel pump charge system per as usual.
Seeing as it is super cab checked for chafing on wiring to fuel pump under cab. Looks fine. I've heard tell could be alternator, which seems odd to me. Wondering if it would be worth pulling it off and taking it in for a bench test? Maybe I missed something. I know the intake gasket is suspect.
Ford Ranger / B-Series :: Gear Shifter Does Not Go Into 1st Gear But Changes To Other Ones
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
Ford Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesFord Ranger / B-Series :: Starts But Pressure Would Immediately Go Back To Zero When Shut Off
Got a 1986 Ranger 2.3 EFI 5 speed that I have owned since it was almost new and will never let it go. 290,000 mls and still running strong "except". Noticed the last couple of months that when I start it cold it fires right off. If I start it hot it always takes 3 tries and always goes on the third try except....on occasion it will not start at all. It is random and after I let it cool a bit (about 30 min) it will start. Over the years I have replace many of the fuel system components (fuel tank pump, high press. pump, inline filter and canister filter, fuel press regulator) but wondering what else might be the problem.
I put a pressure tester on it the other day and when I selected the key to start the pump would spool up to build pressure and shut off. The press gauge would register that but the pressure would immediately go back to zero. After start up it would hold a constant 30psi at all rpm,s. Shut the engine off and pressure drops right down to zero. Shouldn't the system hold pressure for at least a while after shut down? Could this be the problem with my sluggish starts? What would be the normal fuel pressure? Can't seem to find it in my Haynes manual. Once running it runs great.
Ford Ranger / B-Series :: AC Compressor Starts Seizing Up And Burning The Clutch
So I just got done with my first 2 problems of the month with this truck last week. Front end and emissions along with spark plugs. Now, 4 days later this morning, I'm driving the truck trying enjoy the investment, and the AC compressor starts seizing up and burning the clutch. Unrelated but also worth noting, about an hour later the brake pedal gets real soft and the brakes get really sloppy at stopping the truck. The truck also stalled (auto trans) crossing a highway, luckily it was 5am and no traffic was coming.
I'm at $6k invested on a truck with 116,000 miles, and I've only put 6,000 on it. The repairs don't stop, and I've got many more ahead. Like rear suspension, axle, trans, and radiator fluids, and paint, to name a few. Any suggestions on fixing the AC before I drive this truck into a lake?
Ford Ranger / B-Series :: Engine Starts To Race Without Coming Back To Idle
2000, 2.5L standard transmission. IAC replaced about 2 years ago, DPFE sensor and vacuum hoses replaced early last summer. Truck has been running just fine until I washed it last night. Went to work, and when coming to a stop and pressing in the clutch, engine starts to race without coming back to idle. Had to turn the truck off in order to get the engine from racing. Same thing on the way home. What else can/should I be looking at? I did not open the hood to wash the engine off, so it can't be water from the wash.
View 7 RepliesFord Ranger / B-Series :: Hop In The Truck And Belt Starts Squealing - Harmonic Balancer Came Apart
Couple days ago, hop in the truck to go to work and belt starts squealing. Belt was old and it had been raining, so I figured it was a little wet. Turned on the defrost, and squeal gets worse. I then smell a burning. Opened the hood and saw the belt dragging on the a/c pulley, so I figure the compressor clutch is shot.
Looked at it today. I was wrong. Took off the belt and the a/c pulley spins fine. I can turn it's front hub by hand as well. I look around and see the crankshaft pulley isn't lined up. It looks like the outer pulley portion separated from the rubber. This caused the belt the jump and ride on the rubber part, cutting grooves in it.
Here's some pics:
From top driver's side:
From top passenger's side:
From bottom passenger's side: