Ford Ranger / B-Series :: Instrument Cluster Lights Won't Turn On?
I have 87 Ford Ranger. 2.9L 4x4. Before any tips, I have checked the fuses, I have changed the Switch for the lights and the instrument cluster. Still no luck. I don't know if there is something wrong with the wiring. But what I was plan on doing is finding out on one of the Wiring Harnesses on the back of the Cluster which wire turns on the back lights on the cluster. Everything else on the cluster works (Gauges, Highbeam indicator, all the warning sign lights). What wires are what on the wiring harnesses. I was going to just run the wire to its own switch.
View 1 RepliesFord Ranger / B-Series :: Instrument Cluster Bulb Sometimes Does Not Came On When Turn Lights On
One of my bulbs sometimes doesn't come on when I turn my lights on. I actually have to hit the dashboard to get it to come on. Does it randomly. Ironically, it's been doing this ever since I pulled the instrument cluster out to change a different bulb. I don't know if I did something when taking it out or putting it back in. Anyway, what I can check to see why it's doing this? It's just one bulb that illuminates the right portion of the tachometer.
View 1 RepliesFord Ranger / B-Series :: Parking Brake Instrument Cluster Lamp Always On
The parking brake instrument cluster lamp is enabled by a small switch at the foot operated park brake mechanism. The switch is attached to chassis electrical ground. The switch has one wire attached to it. So when the switch is enabled it connects chassis ground to the wire therein turning on the cluster lamp. With the wire disconnected from the switch the lamp stays on. This tells me the wire is grounded somewhere. Brilliant deduction eh?
So here's my question. How/where that wire is routed? I lose sight of it approx. 2-inches from the switch where it disappears behind the brake mechanism mounting bracket. I plan to unbolt that bracket to see if that might be where the wire is being shorted to ground. But if it's not pinched there, where do I go from there?
(2001 Ranger, 4liter-2wd)
Ford Ranger / B-Series :: 1997 - Instrument Panel Light Bulb Replacement
I just finished replacing the instrument panel light bulbs on my 1997 Ranger XL, 2.3L, 2WD pickup. I wanted to share how I did this. First of all, if you never have done this before, go slow and take your time removing the dash panels as they are plastic molding and break easily. Allow yourself about an hour to complete the task. You will need smaller sized hand sockets to remove the screws. The very first thing you should do is remove the negative battery cable from the battery. This way you will not risk shorting out anything electrical as well as possibly triggering the airbag in the steering wheel column.
The key piece in starting the process is to remove the radio first and then central console panel that houses the radio. It pops out very easily by gently prying it out in the four corners. Once you get that piece out remove the screws the support the lower knee panel. In order to get that piece off you will have to remove the two screws the hold the hood release lever in place. Get under the dashboard and look up as you lay looking upward near the brake pedal. Pull the hood release lever and you will see the two gold screws. Remove them. This will free up the panel on the under side. The top side of the panel will pop out if you pry it gently on the top two corners.
Next, you will see a metal panel underneath the knee panel. Remove this metal panel as well. Now you will be able to remove the instrument cluster panel piece. There are some visible screws holding this in place, remove them and gently pry the cluster panel out. Once the cluster panel cover is out you will have to actually remove the gauge cluster itself by removing the the four screw bolts that secure it in place. After the screws are out, gently work it out of the dash slowly as you will need to disconnect three electric plug harnesses in the back.
After it is unplugged and out, on the backside of the instrument cluster you will see some round, black colored thumb screw bulb housings that house the light bulb. Just twist them and turn making sure to go in the right direction. Feel it out for the direction, I cannot remember which way it turns. The bulb housings are labeled "ILL" on the circuit overlay. I recommend you replace all the bulbs as you might not want to have to do this again in the near future. Once all the bulbs are tightly seated and installed just reverse the above process for installation. This is a fairly easy job and like I said it takes about an hour. Make sure you test the lights after finishing.
Ford Ranger / B-Series :: Fuel Filter Removal / Replacement
I know where the filter is, i know how to bleed off the pressure. Im wondering if those clips are easy to slide off to remove the filter from the lines?
View 7 RepliesFord Ranger / B-Series :: 1996 - Power Steering Replacement
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 RepliesFord Super Duty (1999-2016) :: Changing Instrument Cluster - Removal And Installation Of Needle?
I will change the cluster lights to blue LEDs.
Some "leftover" questions:
How do I get the needles "clear" instead of red?
How to remove and reinstall the needles the "right way" (e.g. calibration)
Everything else I could find here in different posts.
Golf IV / Jetta IV :: 1999 - Instrument Cluster Removal Affect Immobilizer?
I am going to remove my Instrument Cluster for an illumination LED changing, to convert them to the white colour. I found out that Immobiliser is located on Instrument Cluster, is there anything I have to be careful?
It's 1999 Bora. I think Immo 2 on it.
I found one Thread that someone had the problem with Immobiliser after cluster removal (it was also for LED job), a car was not starting, he suffered some time tried lots of things, but then everything went OK, even though he wasn't sure what was wrong.
So, do you think there is a high potential risk to take it out? Do you think I have to cut battery connection beforehand?
Prius (Gen 2) :: Instrument Cluster Panel Replacement?
My instrument cluster panel went out. I bought one on ebay and I would like to replace it myself. Is there a step by step video or a diagram that will show me how to take the dashboard off?
View 1 RepliesGolf IV / Jetta IV :: 2003 - Instrument Cluster Replacement
Currently my gas & temp gauges do not work, so I assume the cluster is shot or needs fixed etc. my question is can I simply replace it with a used one from eBay, or do I need to send this one back to be programmed? I was reading about the immobilizer which I assume the 2003 is subject to as well?
View 1 RepliesFord Super Duty (1999-2016) :: F250 - Instrument Cluster And Steering Wheel Bulb Replacement
I found one thread in FTE regarding replacing instrument cluster bulbs but the solution was to contact Circuit Board Medics. I have one dark area on the right side of the tach and another dark area on the left side of the speedo. Probably the same bulb that's out. Also, can attempt to replace the bulbs (assuming its a bulb and not a fiber optic of some sort) in the steering wheel volume and fan controls?
View 3 RepliesBuick - Skylark :: Anti-theft Light Will Not Go Off After Instrument Cluster Replacement
We just replaced instrument cluster and turned the key to on position for 10 minutes. We waited for the anti-theft light to quit flashing and the car runs great but the anti-theft light will not go off. How can I fix this problem?
View 4 RepliesFord Super Duty (1999-2016) :: 2012 F350 - Change Out Instrument Cluster With Mph Cluster?
I have a 2012 F350 XLT that came out of Canada. So of course the speedometer is in KM. (Large numbers are km and smaller numbers are mph). I am trying to find out if I can simply change out my cluster with a mph cluster???
View 4 RepliesFord Ranger / B-Series :: 1997 - Speedo / Cluster Diagram?
I have a 97 ranger 2.3L (manual transmission) and want to change the cluster to one with a tach... I have a 2000 cluster but I would like to compare the actual wiring between the two (1997/2000)... I have looked in the Ranger technical area of these forums and also did a search for "dash cluster wiring" and found no info...
View 4 RepliesFord Ranger / B-Series :: Top 2 Bolts Removal Of Transmission?
How in the heck do you get the top 2 bolts off of the transmission housing? They seem to be positioned in such a way that they are impossible to remove.
View 14 RepliesFord Ranger / B-Series :: 2000 - Codes PO500 - Cluster And ABS Module Faults
I am looking for the part number for the ABS speed sensor mounted on the rear differential for my 2000 Ranger XL 4x4 3.0 flex fuel model. I am also looking for the name of the part so I can look it up on the ford parts site. while looking I have found these names ABS speed sensor
Powertrain Control Module Speed Control Sensor
I had my truck in the shop and they did a health check, they found these codes po500 - cluster fault and the abs module fault
Ford Ranger / B-Series :: 1993 - Wiper Motor Removal?
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 RepliesFord Ranger / B-Series :: 2000 - Harmonic Balancer Removal?
I have a 2000 2.5 and need to remove the harmonic balancer. Are the threads righty tighty or lefty loosey.I'm replacing the timing belt and pulley
View 1 RepliesFord Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?
I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.
View 1 Replies