Ford Brakes/Suspension :: 1999 F350 - Caliper Won't Release Fully
I have a 1999 F350 single rear wheel Superduty truck that will not allow the right rear caliper to fully release. I replaced the caliper/mounting hardware/pads/rotor. The problem continued so I replaced the rubber hose to the caliper. Problem continues. I'm thinking possibly the center rubber brake line at the differential (where it splits and goes right/left) but at this point I am guessing. Maybe proportionate valve but I know nothing about them.
View 11 RepliesPrius (2001-03) :: Rear Brakes Won't Release Properly?
I have a 2001 Prius, with disc brakes both rear and front.
View 1 RepliesIS F (2008-2014) :: Front Brakes On Driver Side Squeals On A Stop And Release
Front driver side brake squeals on a stop and release. This is the only side that produces this noise. Brake clearance is still very good and this noise has been off and on since i bought the car in December. Car has about 25k miles on it and will be replacing brakes at 30k.
Brake issue - YouTube .....
Ford Ranger / B-Series :: Rear Drum Brakes Not Working
Received the truck, 1989 Ranger XLT long bed single cab from my mom. It had been used by my younger brothers for some years, and then sat at mom's for a couple years.
It needed new front brakes badly, so replaced rotors, and pads. No unexpected problems there.
Looked at replacing the rear. Both adjuster cables were initially broken, so they obviously weren't adjusting, or braking. Replaced with a hardware kit, and shoes, and drums. Its the 9" drums, BTW.
Still not actually braking. I can tell this, when at a stop sign in the winter, with the brake pedal held down, and the backs will still spin, with the tranny in D. Even on gravel or grass, this'll happen.
One shop told me this is because the axle seals are leaking. THey've never leaked badly, and the axle fluid isn't low, by and shade of the imagination. Also, this theory falls apart, when the parking brake works just fine, right? Its just hydraulically that they don't work.
I've since replaced the wheel cylinders, the brake line from the frame to the rear axle, and the master cylinder. No change. Bleeding them doesn't seem to be a problem; i.e. no lack of or little fluid witnessed, it seem fine.
Also have bypassed the RABS valve for about a year or so, and its made no difference. Last fall I pulled the drums off, and manually adjusted them, and it didn't seem much better either.
Ford Ranger / B-Series :: 1998 - Rear Brakes Locking Up Very Easily
I just had new shoes, hardware, wheel cylinders, drums, leaf springs, rear shocks, and shackles put on. The brakes were done about 4 or 5 months ago and the springs and shocks just a few weeks ago. The rear brakes were locking up after I had the work done, but I thought they were just too tight. I loosened them a little but it only worked a little.
Now it's starting to lock up pretty much every time I apply the brakes. The ABS kicks on and the rear tires skid. I took the drums off today and didn't see any leakage or anything out of the ordinary. They weren't too tight and I readjusted them but they weren't out of adjustment much if at all. I looked at the Ford symptom chart and it says for brakes that lock up easily there could be sticking or binding components. I didn't see any. Then it says check parking brake components.
Now I see they didn't hook up the equalizer bracket that goes to the front leaf spring hanger when they changed my springs so I assume thats why my parking brake pedal goes to the floor. Then it says check the shoes and linings, which are fine. The last thing it says is to check the fluid control valve. Which I'm guessing is the prop valve.
The only way to check it according to Ford is swap it for a known working valve. One person told me that it could actually be a bad brake booster check valve. Is that possible? Anything else that's common? It's got 272,000 miles on the frame but everything's been changed that typically wears out at least once.
Ford Ranger / B-Series :: 2004 - Rear Brakes Howling And Locking Up
I have a 2004 Ranger 4x4, 4.0, auto and have trouble with the back brakes howling, locking up and generally driving me nuts. I've replaced the drums, shoes, cylinders, emergency brake cables and all the hardware. We've bled all 4 numerous times, blown out the lines, looked for leaks and done all we can think of. What am I missing?
View 1 RepliesFord Ranger / B-Series :: 1999 - ABS Warning Light / Rear Brakes Locking Up
I have a '99 Ford Ranger XLT 2WD. I've been having this problem with my rear brakes locking up on me while slowing down and pressing the pedal to stop the forward movement. There are four components which could cause the problem. My OEM Ranger Repair Manual suggested to replace the Proportional Control Valve which I did however that did not correct the problem. I don't have the Brake nor the ABS Warning light coming on and they check out OK during the start up. I have no problems braking from any speed except when coming to a stop. I inspected my front disk and the rear shoe brakes and they seemed to look OK. The other components which could cause the problem are the Control Module, RABS valve and the Speed Sensor. My question is: If any of these components malfunction, shouldn't the ABS Warning Light come on?
View 2 RepliesFord Ranger / B-Series :: 1990 - Rear Brakes Locked Up When Hit The Brake Pedal Hard
I have a 1990 4x4 ford Ranger, the little truck was purchased in early 2008 as a work truck but has ended up becoming my main vehicle, it has been a good truck for the most part but know I am having some brake issues, well have been having for some time but they seem to come and go. Usually it happens when I have to hit the brakes hard, the rear brakes lock up, I replaced the master cylinder months ago and thought that fixed it, then a month later it happened again. The last time it happened was friday, the time before that was in march 09'.
I have searched this online and found numerous try this but the original poster never comes back to say if the problem is fixed or what fixed it. My ABS light DOES NOT come on when this happens, it does function properly, it illuminates when the key is turned on then goes off. My parking brake no longer works either but I think that is from me "driving thru" the locked up rear brakes. I plan on replacign both drums and shoes within the next week but would like an option to repair the locking up issue.
Ford Ranger / B-Series :: 1996 - Turns Over But Just Doesn't Want To Fully Start Up
So I just finished redoing my head gasket. Everything is hooked back up the way it was prior to the tear down. I'm getting spark, fuel, compression, timing was set correctly according to Haynes, turns over but just doesn't want to fully start up.
View 3 RepliesFord F-150 - 1997-2003 :: 1999 4x4 - Brakes Grab A Bit Then Release When Going To Stop
On said truck, when you go to stop, the brakes grab a bit, then release , then the pedal goes to about 2 inches off the floor, then they grab and hold. Pumping does nothing. No abs light on the dash. Today we put the truck in 4high and while back up I had full brake pressure from the top. Also when you take off, either in the mornings or during the day, it has a slight vibration, kinda like a brake grabbing, then all is fine. The brake grabbing isn't there 100% of the time, I would say 95%. I haven't changed the brake pads, rotors, or anything yet. Just didn't want to throw money at it and still not fix the problem.
View 4 RepliesFord Brakes/Suspension :: 1997 F150 - Converting Drum Brakes To Rear Disc Brakes?
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
Ford Ranger / B-Series :: Opening The Hood Without Using Release Cable?
My battery went flat and to compound my misery, when I went to open the hood, the cable was snapped. How I can open the hood without using the release cable ? I'd rather not have to pay for it to be taken to the mechanic and then also pay to have the battery changed !
View 3 RepliesFord Ranger / B-Series :: 2008 FX4 - Rear Leaf Spring Squeak
I've got an '08 FX4 that has developed quite a loud and annoying squeak from the rear leaf springs. It happens when I'm slowly applying power and going over bumps such as speed bumps or similar. More so when I'm going up hill.
I initially thought it was a u-joint going bad, and had my driveline mechanic take a look at it. He discovered it was the rear leafs making the noise. He sprayed them with an aerosol light grease and the noise was instantly gone. The problem is, the noise comes back after the grease spray has worn off (usually after driving in the rain) which happens a lot in the Vancouver area.
This is my 3rd Ranger and I have never had this problem. I don't drive in unusual places (beach, sandy, dusty areas) so I don't know why this is happening. It does look rusty in the areas that I can see in between the individual leafs. Is this a common problem for this vintage of Ranger?
Ford Ranger / B-Series :: 1993 - Clutch Release Bearing Install
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
Ford Ranger / B-Series :: Cruise Control Stuck On And Wouldn't Release
So I'm motoring along a country road with the cruise set at 50 mph and the truck starts to increase speed.
Tap the brake - nothing happens. I'm up to 65 mph! Knock it into neutral and it revs to around 3,500 rpms and then it unsticks.
What in the world is going on with that? After thinking on it, a few miles farther on and I set the cruise again.
It began immediately picking up speed. I hit the brake and nothing happened. Then I hit the off button and nothing happened.
So again I bumped it up into neutral and it did the same thing - revved for a moment and then kicked off.
The dealership where I get my service done can't get to it for several days. So I'm checking in the meanwhile to see possibilities to identify a cause.
Ford Super Duty (1999-2016) :: 2008 F350 - Rear Brakes Got Quite Hot After Driving For About 15 Minutes
I just changed all the pads and rotors on my 08 F350. The brakes are much better now, only the rear brakes got quite hot after driving it for about 15 min. Turns out the rear parking brakes are dragging on the back brakes. I adjusted the parking brake on both sides so they no longer drag and the heat issue is gone. The problem now it the parking brake does not engage until the pedal runs out of travel. Any tips to get this just right? Will the parking brake self adjust like the old drum brakes and shoes use to do years ago?
View 7 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Left Rear Brakes Hanging Up
Took truck out for a ride and stopped for gas. I smelled Brakes and upon inspection found the left rear brake pads were not releasing. Any take on what could be holding it? 2008 F-250.
View 10 RepliesFord Brakes/Suspension :: 1989 F150 - Park Brake Won't Disengage When Release Lever Pulled?
my park brake will work when pushed to the floor but when i pull the release lever it will not disengaged.
View 1 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Brakes Burning Smell / Wheels And Right Rear Was Very Hot
I have had the truck just under a year. It has 104k on it i only drive it on weekends. Last weekend going to Home Depot about 15 miles got out and could smell brakes burning. Felt the wheels and the right rear was very hot. Got back home no smell but still hot not as hot as earlier. Pulled the wheel off it looks as if the pads and calipers are fairly new paint is still on them caliper is a TRW. The pads were stuck in the carrier even the stainless clip ends look rusted.
Cleaned it all up both sides lubed the pad carrier with pin lube. Pushed the calipers back in some both sides went in easy. The right rotor has definitley been hot. Put it all back together and went for a test drive. Came back no problems checked the temperature with a laser type heat thermometer all wheels were around 140 f. Went out yesterday morning stopped and could smell the brakes again. Drove it back home and the right rear was 300 f. others 150 to 160 f.
Jacked it up put it in neutral and the you can spin the wheels by hand. Started the truck had the wife get in put it in drive wheels turning applied the brakes they stopped let go they turn freely again tried the parking brake it works fine also. So do I buy new calipers and brakes or maybe is the wheel bearing going bad causing the brakes to heat up?ied.