Ford - Mountaineer :: 1998 V8 5.0 - Shaking At 40 MPH / Slightly Rough At Idle
A couple of days ago (Friday, Sept 14th), I noticed my 98 V8 5.0 liter Mountaineer was idling rough. I had the codes pulled and got P1401, P0455 and P0308. I did find a vacuum leak and fixed it (changed the air filter and cleaned the MAF while I was in there). I also replaced all the plugs (based on the P0308 misfire). I cleared the codes after that with a neg battery pull.
I'm still running slightly rough at idle, but not as bad. However, I have found that when I get up to about 45MPH (1500 RPMs) I started to get a worrisome shaking/ vibration. It's difficult to tell where it is coming from. If I let off the gas, or give it more and go up to about 50 mph, the shaking stops. It is only when I'm pressing the pedal in this range (like it is having trouble switching gears, perhaps?). Over the past two days of driving it and testing, I have been to autozone and had the codes checked. Nothing comes up, and no CEL.
I just had a new trans put on about 6 months ago. The only thing that preceded this issue was I got an oil change the day before this started at a place I don't normally go to (unlikely, but since they didn't write the type of oil they used on my window tag, I figured I'd mention it). I've read some suggest it to be a tire issue; but that strokes me as odd, since the shaking only happens when applying gas.
Ford - Mountaineer :: 2004 - Running Rough - CEL On - Ticking?
Mountaineer started running rough couple of weeks ago with engine flashing. Had codes read, got codes P0306 and P0316. I changed the coil pack of cylinder 6, engine light went away but still running rough. Decided to change all plugs. Found cylinders 2 and 3 filled with oil so I changed the valve cover gasket. Put back together, still running rough and ticking. Pulled every coil pack and metered them.
Every one reads .6 ohms across terminals and 5.6k from each terminal to spring. I'm assuming this indicates a good coil pack. I also metered the one that I took out and it reads the same. I've also looked for vacuum line leaks and listened but found none. The engine is rocking pretty bad and the exhaust comes out in the pattern of the "misfiring". Went to see if Autozone could read a code without the engine light on but they read "no codes".
Ford Ranger / B-Series :: 2003 3.0 - Misfire On Cylinder Six / Running Rough And Check Engine Light On
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 RepliesPassat (B6) :: Engine Running Rough And CEL On - Misfire On Cylinder 2 And 4
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
Lumina :: 1990 3.1 L Engine Misfire When Cold - Running Rough
I have a 1990 3.1L, multiport fuel injection (NOT sequential FI), which runs very well most of the time. However, when I cold start it runs rough (misfire) for about 1 minute (no throttle) or until acclerated. The is no misfire when running normal, but it might be running a little rough when stopped at a traffic light (in Drive, foot on brake).
I put new plugs and wires on, but it did not affect this problem.
I am not using coolant, or oil, the plugs that were removed were somewhat worn, enough that I expected to notice a difference after they were changed.
I have not yet (1) cleaned the MAF, (2) checked carefully for vacuum leaks, (3) checked for leaking injectors.
Since this is a 1990, OBDI, I can't say which cylinder is misfiring or how the fuel trims look etc.
Avalon 2005-12 :: Misfire And Check Engine Light Came On - Car Is Running Little Rough
My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.
View 1 RepliesCelica :: 2000 1zzfe Engine Was Running Rough - Cylinder 1 Misfire
Okay so last year i bought a 2000 celica gt manual with 50,000 miles, and currently has 67,000 miles. A few days ago I started to notice the engine was running rough and then about 10 miles later the chack engine light came on. I promptly went to the auto parts store to read the code. I was informed I have a cylinder 1 misfire. Naturally i replaced the spark plugs with NGK iridium, reset and rechecked engine code. Same code. Next i swapped the coils from 1 and 2, reset and rechecked. same code. I then swapped fuel injectors from 1 and 3, rest and rechecked. Same code. So now i am a bit stumped.
Only faulty equipment prior to this incident would be 2nd gear synchronizer. Only applicable above 5,800 RPM.
Elantra MD (2010-15) :: Running Rough / Check Engine Light Came On And Misfire Code
In the last month, my car has had an awful time starting on 2 different occasions. The first time it ran really rough for about 1 minute then was ok. The second time was the same but the engine light came on. Took it to an out of town dealer and he said it showed a misfire code but could never find anything else and all looked OK. Spark plugs?
View 4 RepliesDodge - Durango :: 2003 - Code P0300 Random Misfire / Engine Running Rough
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 RepliesSubaru - Legacy :: Slight Rough Running With Cold Engine And Stumble Below 2000 Rpm / CEL Misfire Code
I have had some slight rough running with a cold engine and stumble <2000rpm. Finally it tripped a CEL which was read as a misfire code.
The mechanic swapped the coil and plug(recent) and no change. He did a compression test and air blew out the exhaust. So.......the car needs a valve job which entails motor removal and fixing the head and reinstall. He rough estimates this at $2000 and rate is $65/hr.
He mentioned looking at pistons and may be a bit more if rough.
This car well maintained (170,000 miles 2005 Legacy turbo wagon with manual)...
Nissan - Maxima :: 1998 - Check Engine Light Come On And Car Started Running Very Rough
1998 Nissan Maxima had a check engine light come on and started running very rough. I took it to get a code read and came up with P0320 and P0325. I'm not worried about the 0325 since that's a knock sensor. 0320 is a misfire on cylinder 2.
With the car idling, I pulled the power connector from coil pack 2 to see if it made a difference in the idle - nope. I did the same for the other cylinders, and each responded with a noticeable change in the idle, which was remedied when it was reconnected.
I moved the coil pack from #2 to #4 (swapping them) and the same problem existed - idle was rough and didn't make a difference when I pulled the power on 2, but it did on all other coil packs. So, it seems the coil pack ins't the problem since multiple packs don't seem to make 2 work, but they work on other 4 and 6.
I then pulled the spark plug from cylinder 2, it was very black and looked in bad shape. I replaced it. Still no love.
I then put a spare plug in the coil and was able to see spark as the engine ran, so it seems that the coil pack at 2 is getting juice.
So, I have gas (big odor when the car is running - seems super rich) I have spark. Still running very rough and the 0320 code remains.
Ford F-150 (2004-2008) :: Running Very Rough / Shaking At Low RPMs - Truck Died
On my way into work this morning, my 06 with the 5.4 started running very rough/shaking at low rpms. I could kick it out of overdrive and it would smooth out and seemingly be fine at higher rpms.
This worked out for a couple of miles until the truck just died on me completely. The Edge is showing po351, 352, 353......358 codes. Ignition coil Primary/Secondary circuit fault on every cylinder.
I'm thinking its unlikely that every coil failed simultaneously....computer? When I try to start the truck, it will try to hit on a cylinder or two, but will not run.
Ford Excursion :: 2000 V10 Running Rough - Tug Or Misfire At Low RPM
I have a 2000 excursion 4x4 v10 with 90k. The past few months I've noticed a tug or miss fire at low RPM (2000 AN UNDER) the past week its gotten worse, some occasional rough idol and the missing is getting worse. Whats wrong?? I don't want to take it to ford yet! No Check Engine Light yet...
View 14 RepliesFord Ranger / B-Series :: 2003 - Misfire And Rough Running / Flashing CEL
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
Ford F-150 (2004-2008) :: Misfire / Running Rough And Knocks Like A Diesel
I just bought a 2007 F150 XLT with a Triton 5.4 with 80,000 miles on it. My problem is this, the engine seems to run ok ( a bit rough) until it gets up to running temp and I have driven about 10- 20 miles then most of the time, it starts to act up.
When I am driving it is fine, but when I slow down and come to an idle about 500rpms, it sometimes runs very rough, sounds like a diesel and shakes violently. It feels like it is doing damage. Sometimes it stalls. If I rev it back up immediately it will smooth out.
In speaking to some friends they've suggested things from plugged oil channels, (affecting the cam phasers? All the way to it needing new chains, phasers and guides. I don't want to spend a ton of money doing an improper service repair only to have the issue show up later . But there seems to be a lot of different answers to the same problem. Is the dealer going to be able to diagnose something like this fairly well? Or should I try to narrow it down a bit first?
BMW :: 2006 Shaking And Running Rough After Valve Job
I had a valve job on my 2006 Bmw 750 li, when I picked the car up from the shop the engine was loud ,before the job it was quiet couldn't tell the car was on , it also shakes back and forth while idling at every stop light,and when I take my foot off the gas the engine kind of jerks I have taking it back to the shop several times and they seem to not know what it could be they have recalibrated the valves and it seems to not shake soon after I leave but right when I'm a mile or so away it starts to shake again, what could be causing this? I'm pxxxed I paid them close to 4000 to replace the valves and now the car is running rough.
View 15 RepliesBmw - 325 :: 2005 - Car Running Very Rough / Shaking Intermittently
I have a 2005 325xi BMW with 31,000 miles I get regular oil changes. Recently the engine seems to be running a little rough. The other day, after driving about 15 miles, the car started shaking and getting progressively worse. At first it seemed like the tires, but later it seemed like the engine. Also, when I accelerate, it seemed to get more rough, but again, not all the time. Last night, it was the worse yet. After I left the car for 2 hours, it didn't happen right away. Then it did again, but with 2 more miles to go til home, it stopped! Not sure if it's the fuel pump, fuel filter or even something with the wheels (sway bar?)?
View 10 RepliesFord - Taurus :: 2005 Started Running Rough - CEL Came On / Cylinder 5 Misfire Detected
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 RepliesFord Aerostar :: 1990 4.0 Liter - Running Rough / Exhaust Smells Like Gas And Has A Misfire
1990 Ford Aerostar. When I start runs really rough and has excessive fuel consumption and the exhaust smells like gas and has a misfire my friend says its the coil pack going bad im not sure. I love my ford aerostar dont wanna get rid of it.
View 5 Replies